similar to: snmp ups Status: Not supported

Hi, I am running samba and lprng for 4 hp laserjets. Sometimes a samba print job goes to the wrong printer. Normally everything works just fine. Shown below is the lprng acct log file enries for the concerned print job. Please notice that the print job was supposed to go to hp4050-mail, but ended up in hp8100. Any suggestions are much appreciated. Thanks Balagopal jobstart

Thanks Alan! On Mon, Jun 11, 2018 at 4:54 PM, Alan Bartlett <ajb at elrepo.org> wrote: > On 11 June 2018 at 20:21, Ricardo Martinelli Oliveira > <ricardo.martinelli.oliveira at gmail.com> wrote: >> Thanks, I got access now. >> >> One question: how can I create a page for my username? e.g. >> https://wiki.centos.org/KaranbirSingh >> >> I see a

Thanks, I got access now. One question: how can I create a page for my username? e.g. https://wiki.centos.org/KaranbirSingh I see a create page link, but it also says I'm not allowed. On Mon, Jun 11, 2018 at 4:10 PM, Akemi Yagi <amyagi at gmail.com> wrote: > On Mon, Jun 11, 2018 at 11:16 AM, Ricardo Martinelli Oliveira > <ricardo.martinelli.oliveira at gmail.com> wrote:

Hi, Being part of the CentOS PaaS SIG committee i'd like to request access to the PaaS wiki page and all its child pages so i can start editing the content and keep it up to date. My Wiki user name is RicardoOliveira. Please let me know if you need any other information. Thank you, Ricardo Oliveira

On Mon, Jun 11, 2018 at 1:24 PM, Ricardo Martinelli Oliveira <ricardo.martinelli.oliveira at gmail.com> wrote: > ah, but there is still that thing that I cannot edit the page. I > promise it will be my last request. =D >>> I have now initialised a Wiki Homepage for you -- >>> >>> https://wiki.centos.org/RicardoOliveira Please try again :) Akemi

Has anyone out there compiled R for the Umbutu Linux* (ne? Debian) v. 5.04 distribution for Intel-type platforms (32 and 64 bit) ? Thank you, Derek Eder * Umbutu, a popular new Linux distribution, not a Nigerian scam, I promise! http://www.ubuntulinux.org/ -- Derek Eder SDS KLINIKEN Vasaplatsen 8 SE 411 34 G?teborg (Gothenburg) Sweden phone: +46 (31)* - 10 77 80 fax: +46 (31)* - 10 77

Ok, I installed the ups, and installed nut, and /proc/bus/usb/devices says this T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=1.5 MxCh= 0 D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=06da ProdID=0002 Rev= 0.01 S: Manufacturer=POWERWARE S: Product=Powerware UPS C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr= 20mA I: If#= 0 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=00 Prot=00

Hello, I am trying to setup a pxe server, I have a debian box with tftp-hda install, the image in place, and the pxeserver.0 in place. I have a router with udhcpc and I would like to use that as the DHCP server for the pxe server... I have been searching for some sort of document or hint as how to set this up, I could not find anything. Does any one know where a good document on this is located

Adam: Thanks for putting up this page. But something is wrong. In particular, our Powerware 9135 is a three phase UPS system with THREE 480 volt outputs. So the displayed voltage is not correct -- in fact there should really be THREE voltages displayed, all around 480v. Nut developers: I am copying the NUT mailing list to see if anyone can suggest how to fix this. NUT developers, see the

Hi, Made a test build of the Testing branch. The problem is that upsmon and upsc is not respecting the revision change of libupsclient.so. It is now libupsclient.so.1, but i get this. /usr/sbin/upsmon: error while loading shared libraries: libupsclient.so.0: cannot open shared object file: No such file or directory and: upsc: error while loading shared libraries: libupsclient.so.0: cannot

Hi, I have an HP R5500XR and a Compaq R3000XR that I would like to use with nut. I searched the compatibility lists and the mail list archives but couldn't find anything. They both have 9 pin serial ports. Can anyone give me any information about them, and if they are supported by nut? Thanks, Denny Fox

Hi Arnaud, Any luck with the latest subversion trunk? From: Greg Sent: Wednesday, May 13, 2009 10:34 PM To: Greg ; Arnaud Quette Cc: Kjell Claesson ; nut-upsuser at lists.alioth.debian.org Subject: Re: [Nut-upsuser] Nut and PowerWare 5115 Hi Arnaud, Some more testing on Ubuntu 9.04. Here is the output of bcmxcp_usb and lsusb ============================================ root at

Hi, Need to get an answer to the following. I find the naming to be little redundant regarding the 'input.transfer.boost.low - hige'. The same goes for input.transfer.trim.low - high. As I find it, there is only one point where the boost or buck (trim) kicks in. Let's say that the nominal voltage is 230 volt, then we have a input.transfer.boost point on say 220 volt. If the

Hello all, I have obtained a Compaq T700 H UPS sans-cable. My research indicates it would've come with a HP #201092-001 cable, and from previous posts on this list, it speaks upscode2, possibly being a rebadged Eaton unit. Any suggestions for cable pinouts I can try? Regards, Mathew McBride

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Has anyone used nut with a XPCC UPS, in particular one of the XVRT units? Their supplied monitoring tool "works", but I'd really prefer to use nut if possible. I've systematically gone through each of the drivers in /lib/nut and none seem to talk with the unit properly. I'll be talking with a XPCC support person tomorrow, though

All, I have a Cyberpower UPS that I have been working with for about a year. I have used NUT in the past with good results, but as of late have been seeing issues with nut talking to the UPS. I will start with the information on the server that is running NUT, and has the UPS connected VIA an RS232 cable. O/S : Fedora 9 Kernal (uname -a): Linux haruhi 2.6.26.5-45.fc9.x86_64 #1 SMP Sat

All, I have a Cyberpower UPS that I have been working with for about a year. I have used NUT in the past with good results, but as of late have been seeing issues with nut talking to the UPS. I will start with the information on the server that is running NUT, and has the UPS connected VIA an RS232 cable. O/S : Fedora 9 Kernal (uname -a): Linux haruhi 2.6.26.5-45.fc9.x86_64 #1 SMP Sat

Hi. Have back-ported the bcmxcp and bcmxcp_usb driver from Development. I hope it's done right. Tested a clean cvs fetch after commit and it build and install ok. Regards Kjell

tisdagen den 16 december 2014 15.36.29 skrev Frantz de Germain: > Hello, Hi Frantz, > > I'm testing an APC SMT3000RMI2U connected to an USB port with Nut 2.7.2. > I've got the message : > > "interrupt pipe disabled (add 'pollonly' flag to 'ups.conf' to get rid of > this message)" > > I've been looking for "pollonly" in

I ran into a portability issue with drivers/bcmxcp.c in nut-2.4.1 on my UnixWare 7.1.4 machine. The error I get is ..... UX:acomp: ERROR: "/opt/src/utils/nut-2.4.1/drivers/bcmxcp.c", line 835: integral constant expression expected ..... Looking at the code we see ..... int init_outlet(unsigned char len) { unsigned char answer[len]; ..... Although gcc can handle it, it's not