similar to: mge-shut don't reboot ups by default

Hello, looking for replacements for some older Powerware equipment I found the MGE Pulsar Extreme 1000C and I'm currently testing one with nut-2.0.3 on a self-brewn i386-linux. Upto now everything seems to work fine - except I can't get the power outlets switching on again after mains returns. As this works with Personal Solution-Pac 2 on W2k I thought that there might be a way to

I have an Ellipse USBS connected via serial cable to a CentOS 3 box. Do I need to turn off the UPS as the final stage of shutdown, or will the UPS power itself off, before the battery reaches a level to low to safely recharge from? I notice there is the option for the UPS to turn itself off (and on again) unattended if power is restored during shutdown, but there doesn't seem to be an option

Hi there, I've replaced yesterday my old UPS with a brand new "Eaton Ellipse MAX 600 USBS". I've choosed the Eaton (previously MGE) both because I've always been extremely satisfied with MGE UPSes of all kinds at work, and because of the involvement of MGE (with Arnaud) in nut development, which made me quite sure that I would have no trouble with an Eaton (MGE) UPS and

I'm struggling to configuring nut for MGE Pulsar Ellipse 800 (at least Ellipse 800) for two boxes - home firewall and file server. I'm using Debian 4.0 Etch, every one of them. I'm built (after some dangerouse experiments) a testing configuration, where boxes are plugged to line, server playing as a master, firewall as a slave, and UPS connected to an electric heater about 300 Wats (no

Thanks for suggetions and keep me indumb about making of Debian packages:D I will try this package "nut_2.2.0-2_i386.deb" One little questionm, shoud I use newmge-shut driver? - my ups is quite old - more then 3 years, connected through serial cable. >> PS: Arjen de Korte suspected something was wrong around my "heater" load, >> for now I have used two 150W lamps

Hi all, I just bought a Trust 1000VA PW-4105 UPS. I installed the UPS on FreeBSD 6.1, and installed NUT 2.0.3 via the FreeBSD port. I had no problems installing and configuring nut and the UPS to run with the PowerMust driver. My problem however is when I test the powerdown function by issuing the command: 'upsmon -c fsd' The UPS is cutting the power before the shutdown procedure

Dears, I finally resolve my problem, I just make symbolic link: [test at box var/run/]# ln -s -T /var/state/ups/ nut Now I finally got services online: # /sbin/service ups start Starting UPS driver controller: [ OK ] Starting upsd: [ OK ] Starting UPS monitor (master): [ OK ] BUT, on upsc I

Hello nuters, FreeBSD, Ellipse USBS 800, serial line, nut 2.02 everything works fine. But I'm only able to get an automatic shutdown when reaching the built-in 30% level. I the "lowbatt parameter" is set to anything, it's simply ignored. This is a problem as I want to shutdown around 90% to avoid the battery to drain out when multiple shutdowns occur. Any idea ?

Hi, I am trying to talk to an MGE Pulsar Extreme UPS over RS232 with the mge-shut driver but I'm having some problems. It appears to init OK but I can't, say, turn the outlets off, eg.. harrow:~>upsc mge@localhost battery.charge: 78 battery.charge.low: 20 battery.runtime: 05760 driver.name: mge-shut driver.parameter.port: /dev/cuad1 driver.version: 2.0.3 driver.version.internal: 0.65

On Tue, Oct 2, 2018 at 3:59 PM Charles Lepple <clepple at gmail.com> wrote: > > On Sep 27, 2018, at 6:59 PM, Gabriel <jarod125 at gmail.com> wrote: > > > > Hi, > > > > I'm struggling with a peculiar issue with my UPS. After a power > > outage, the devices powered by it properly shut down via nut. > > Eventually, the UPS also goes down.

Hello, Ren?. > You can change the parameter > ups.delay.start into your UPS to set the "Interval to wait before > (re)starting the load (seconds)" > > use upsset to change the value. So far, the ups.delay.start parameter in my MGE Protection Center 675 has always been equal to the driver.parameter.ondelay parameter (which equals the ondelay argument in ups.conf).

Hi! We have two MGE Evolution 1100 here, and I want to make use of the powershare outlets to force a particular boot sequence on the machines powered by them. However I'm not sure how to set those variables upon NUT starting, without having to change the init scripts to call "upsrw". Is there some place where I can set them, where they can be read automatically on startup? One of

Hi, I'm struggling with a peculiar issue with my UPS. After a power outage, the devices powered by it properly shut down via nut. Eventually, the UPS also goes down. Power is still out, however, roughly 40 seconds after the UPS shut down, it turns back on and it starts supplying power to the load, thus turning back on the devices attached to it. This is obviously not something I want. In

Hi, thanks for your reply. >> The Unit is new, the battery drains because it went down to about 15 >> percent before NUT shuts it down. >> >> Yes, I can here a "clac". The problem is not the shutdown procedure, >> it works quite good. After the Unit reaches 20 percent the NUT-Server >> on the pi shuts down the system and the ups is turned off as

2018-02-28 21:11 GMT+01:00 Jairo Rotava <jairo.rotava at gmail.com>: > Hello, > > I think that on this file nutdrv_qx_megatec.c the definition for > shutdown.stayoff may be wrong. In the file the definition is "S%sR0000\r"m > while on the megatec protocol description ( > http://networkupstools.org/protocols/megatec.html) the command is just > "S%s\r".

Hello there. Have been experimenting with an APC Smart-UPS 1500 RM and would like to share the results of my research. I hope this could be of help to people having this kind of units. I would also like to give something back to the NUT community. :) Here are the details of the unit in question (a 1500 VA rack mountable one): Model: Smart-UPS 1500 RM Firmware revision: 617.3.I USB firmware

>> [Roger wrote:] >>> By the way, do you have offdelay and ondelay values in your ups.conf ? >> >> No, I haven’t. I just added. Should I add more lines here? >> >> maxretry = 3 >> >> [ups] >> driver = usbhid-ups >> port = auto >> desc = "CPS" >> pollinterval = 15 >Yes, ondelay

Hi, I own one a MGE Protection Center 675. You can change the parameter ups.delay.start into your UPS to set the "Interval to wait before (re)starting the load (seconds)" use upsset to change the value. Regards, Ren? Le 2013-12-06 15:14, Angel Tsankov a ?crit : > Hello. > > I am faced with a configuration where the OS (Debian 6.0.8) and the PC > shut down before

Hello. I am faced with a configuration where the OS (Debian 6.0.8) and the PC shut down before the UPS (MGE Protection Center 675). Also, the UPS restores power to attached devices as soon as main power is back but the PC does not detect power restorations that occur less than a couple of seconds, say 10, after its power supply has been cut. As a result, if main power comes back within 10

Thanks for help! Are you happy with your Eaton Elipse ECO 1600? Does it work well with ondelay? I will need some UPS that supports the ondelay parameter. Bartosz śr., 10 kwi 2019 o 13:06 Roger Price <roger at rogerprice.org> napisał(a): > On Wed, 10 Apr 2019, Bartosz wrote: > > > I don't see ups.delay.start anywhere. Here is the output of upsrw: > > > > upsrw