similar to: newmge-shut warning (was: MGE Ellipse 800 shutdown problems)

upsmon.conf using NOTIFCMD and NOTIFYFLG is working well, it is calling my script "notify" on requested events (ONBATTERY,LOWBATTERY and ONLINE). Command #upsmon -c fsd -u monmaster myups at localhost gracefully shutdown my box and after several seconds switch off the ups's load. Two problems: - notify script is called and executed as user "nut" (as it used to be

Thanks for suggetions and keep me indumb about making of Debian packages:D I will try this package "nut_2.2.0-2_i386.deb" One little questionm, shoud I use newmge-shut driver? - my ups is quite old - more then 3 years, connected through serial cable. >> PS: Arjen de Korte suspected something was wrong around my "heater" load, >> for now I have used two 150W lamps

I'm struggling to configuring nut for MGE Pulsar Ellipse 800 (at least Ellipse 800) for two boxes - home firewall and file server. I'm using Debian 4.0 Etch, every one of them. I'm built (after some dangerouse experiments) a testing configuration, where boxes are plugged to line, server playing as a master, firewall as a slave, and UPS connected to an electric heater about 300 Wats (no

> If you set lowbatt=70 then the behaviour you are seeing is normal. Don't > set lowbatt and you'll get the default manufacturer settings which is > LOWBATTERY at 30% charge level. > > Philippe Thanks for quick response! I realized this and forget this setting! For now I think that my box does not recognize signal about low battery - I'm only started to read SHUT

Hello all, I wonder if the improvements to a driver called "newmge-shut" which have been mentioned in October 06 got it to the 2.0.5 release? I tried my setup again with this release and still get this "communication lost -> established -> lost -> established" cycle. USB was not working because of the Solaris 8 installation. Regards, Ingo -------------- next part

Hello. Battery, battery, battery. I am only thinking at worn batteries. I recently had the same symptoms with an hp/eaton g3 1500va. One of the 3 batteries was reading a healthy 12.8v, but when put under load it would quickly drain. I would measure each battery and test them under load, like with a car headlight bulb switched on both fillaments. On Thu, 23 Apr 2020, 16:54 Marc Franquesa,

Hi, recently I observed that during a power outage, my NUT setup doesn't shutdown properly. Indeed it never reaches the LowBattery state to notify and initiate shutdown on clients. Reviewing my setup and logs I think I'm facing multiple problems and I'm unable to point to real root cause. First, let me focus on my scenario and current setup: In normal status (ONLINE, fully charged)

Hello all, I've got an MGE Pulsar Ellipse Premium 800 powering a couple of FreeBSD systems. Driver used is mge-shut, I don't know what the new mge-shut driver offers, but I follow the "if it works, don't fix it" dogma here. :) I also had a nut server installed on the master, with the /usr/local/etc/rc.d/nut script slightly modified to include a couple of upsrw commands

Hi Mutlu, 2009/8/7 Mutlu T. <cmtunc at gmail.com> > Redirecting to debian.org domain due to being rejected as spam by free.fr > > > ------- Forwarded message ------- > From: "Mutlu T." <cmtunc at gmail.com> > To: arnaud.quette at free.fr > Cc: > Subject: New NUT HCL entry / (brand)Inform (series)Informer Compact > Date: Fri, 07 Aug 2009 15:31:04

Dear users, This mail is to announce the beta availability of the mge-xml driver in NUT's trunk. This (overdue) driver allows to support MGE* (UPS Systems and Office Protection Systems) Network Management Cards. This development is sponsored by MGE Office Protection Systems, which is also the NUT sponsor, web hoster and (new) benefactor in general. This driver offers similar services to the

Hi again, As a followup to my previous post, just a couple words to add a comment on the numerous tests I did the past days. It was necessary to increase the waiting time in the /etc/ rc.shutdown, to wipe out the remaining problems (ups didn't shut down). # a rather large sleep to insure the ups stop babbling sleep 20 It appears the ups needs more than 20 seconds to

[fwded to the list] Hi Fran?ois, > I didn't post this on the list as it seems a little bit more MGE > stuff than nut. Anyway feel free to post it if you consider it's > relevant. > > This is the trace you were asking for. The Ellipse 800 correctly shut > down in this test : > > This was running on a i386 recent hardware, the cpu load is under 5%, > 360MB out of

Hi, I recently purchased a Tripp Lite SMART1000RM2U UPS (http://www.tripplite.com/en/products/model.cfm?txtSeriesID=744&txtModelID=2657) and tried to configure the NUT with tripplite_usb driver and encounter the following problems: 1. battery.charge doesn't report correct charge level when the UPS is On Batter. It just reports 0. Even though it will report 100 when on line power. 2. I

Hi there, I've replaced yesterday my old UPS with a brand new "Eaton Ellipse MAX 600 USBS". I've choosed the Eaton (previously MGE) both because I've always been extremely satisfied with MGE UPSes of all kinds at work, and because of the involvement of MGE (with Arnaud) in nut development, which made me quite sure that I would have no trouble with an Eaton (MGE) UPS and

Hello happy nuters, Some complementary words about making nut 2.02 successfully run on FreeBSD with MGE Ellipse. With the usefull information Arnaud sent, it's rather obvious that the erratic response of the ups to the shutdown script is linked to its difficulty to handle large traffic on the serial line. These are the final tweak I made to have this configuration satisfyingly

Hi all, First of all thanks for the great work on nut ! (despite it's not fully functional yet overhere). Everything seemed to go fine until the final test : shutdown the UPS ! The system is running FreeBSD 5.3, the UPS is MGE Ellipse 800 USBS both linked with the MGE serial cable. The system is a remote server, only running some file services and large disks. The porting,

Hello, I'll be back with my MGE Evolution 2200 connected with RS232 I upgrade nut 2.0.1 in nut 2.2 + psp as you ask me PSP autodetect my UPS and autoconfigure NUT. not really diffcult ! So I didn't change anything but I always have in my syslog these event Nov 13 11:09:22 mezenc upsmon[3865]: Poll UPS [mgeups at localhost] failed - Data stale Nov 13 11:09:27 mezenc upsmon[3865]: Poll

Hi I have Pulsar 1000 (MGE) and mge-shut 2.0.5-3. By default mge-shut don;t reboot ups after upsmoc -c fsd, only permanent powerdown. After I add ondelay=30 in config, all nice, ups restarted after 10 sec. But according man mge-shut ondelay measured in tens of seconds and by default equal 3. -- Olleg Samoylov

Hi, I've got two MGE Ellipse 1500 UPS connected via usb to an ubuntu jaunty system with nut and libupsclient1 2.4.1-2ubuntu4. As soon as I start the driver for the second one, they start fighting each other and I get no data. I found an older post to this list that said: If you want to monitor multiple UPSes through usbhid-ups, you *must* make sure that each one can be uniquely identified

I'll be back one more time perhaps I found the reason of these errors Nov 13 11:09:22 mezenc upsmon[3865]: Poll UPS [mgeups at localhost] failed - Data stale it happens when daemon upsd et upsmon are started after the boot obviously, there isn't any errors when upsd and upsmon are started at boot following later ... -----Message d'origine----- De : goudard sabine Envoy? : mardi