similar to: Belkin F6C100-UNV and "-x wait"

Mr. Selinger, I'm CCing you directly since it appears (insofar as I can tell) that you are one of the delelopers for the newhidups driver. This is the third time I've submitted this (hence the CC this time). Hopefully mailman takes it. I've tweaked my SPF records, and I'm hoping that was the problem. My sincere apologies if this has gone through and I just haven't seen it

Greetings all; I pulled a Belkin F6C100-4 into the shop this afternoon, deader than a door nail. Out of service for about a year because (I'm assuming here) that the cooling fan stopped and cooked what little remaining life there may have been out of the batteries, which had swelled so badly I had to split its frame to get them out. They are also in the under 1 volt per 12 volt pack

All, I just bought a Belkin F6C1100-UNV and am trying to get it to work with NUT. I have tried many drivers ( "belkin", "belkinunv", "genericups upstype=4", and "genericups upstype=7", "bestups", "fentonups"). None of them seem to work. Does anyone have any experience with this device? If there is some utility that you all use to

I was getting: "Can't claim USB device [0764:0501]: could not detach kernel driver from interface 0: Operation not permitted" so I manually installed the udev rules the source (I installed the Gentoo ebuild). I am now getting: # upsdrvctl start Network UPS Tools - UPS driver controller 2.4.3 Network UPS Tools - Generic HID driver 0.34 (2.4.3) USB communication driver 0.31 Using

All, I just had a power failure that caused me a little drama. This spurred me into trying to get NUT up on my cyberpower 1500 again. For about 6 months I tried to get it to work with the new power panel drive with no luck. Today I removed all the old files for NUT and installed the newest version I could find (2.4.3) and it works perfectly now with my UPS. Hopefully now I

Hi, I've been fighting with trying to get a Belkin Universal model F6C800-UNV to work with NUT. The error I am getting is as follows: ---------------------------------------------- * Starting UPS drivers ... Network UPS Tools - UPS driver controller 2.0.0 Network UPS Tools - Belkin 'Universal UPS' driver 0.06 (2.0.0) tcgetattr(/dev/ups): Inappropriate ioctl for device Driver failed

Hi, it'd be great if you could update the documentation on the website that some models of the Belkin -UNV series will only work with the megatec(_usb) drivers. I wasted a lot of time on trying to get it to work with the wrong drivers, and would like to spare others the pain :-). Thanks, ~David P.S. Some forum post said that the stable megatec drivers don't work 100% with the belkin UPS,

Hi, it'd be great if you could update the documentation on the website that some models of the Belkin -UNV series will only work with the megatec(_usb) drivers. I wasted a lot of time on trying to get it to work with the wrong drivers, and would like to spare others the pain :-). Thanks, ~David P.S. Some forum post said that the stable megatec drivers don't work 100% with the belkin UPS,

I'm trying to set up a belkin f6c1100-unv UPS to work with nuts. From reading the mailing list, it sounds like the belkinunv serial driver should work and that the USB driver is potentially troublesome. Is this a correct impression? Also I may have missed this but if I do go with the serial (or USB port) is there any simple command line method for verifying basic connectivity? The

Zaid, I have a Belkin F6C800-UNV which has both a serial and USB connector. The serial connection is already working with the Belkinunv driver. I will connect via the USB and then compare both sets of variables. This should allow me to correlate and shed some light on the meaning of many of Belkin's non-standard "Usage" descriptors. With this information, it should be very easy

For the record, I was able to get the following working: Device: Belkin F6C1500-TW-RK Driver: belkin I tried the "belkinunv", which I use for my F6C1100-UNV, but it didn't work. At least there was a driver that worked! :-) Feel free to add it to the list of "tested" configs. Thanks, Dave ---------------------------------------------------------- Are Your Friends

Hi Arjen My apologies fro drifting off topic in the other mailing list...:-) On the bottom of the Belkin UPS unit - is the model number: F6C120auUNV The "au" is for Australia I think. "man belkinunv" states that F6C120-UNV is supported - and I assumed that the "au" would not prevent this. I plugged in the USB to gather the information you requested. My intention

Is anyone besides me using gcc 4.*.*? I noticed that NUT generates an enormous amount of warning noise with that compiler, mostly due to implicit casts between signed/unsigned pointer types. Any volunteers to de-noise the code a bit? The easy way is to insert typecasts; the better way is to actually take care about signedness. -- Peter gcc -I../include -O -Wall -Wsign-compare -c -o everups.o

I have a new Belkin F6C900-UNV. I see that it's not listed in belkin-hid.c The VendorID is 0x050d like all the Belkin UPSes, and the ProductID is 0x0900. I haven't had a chance to actually test the development version of nut yet, since I'm running Fedora Core 6, which still has nut 2.0.3. `newhidups -DD -a myups` gives the error of: Checking device (050D/0900) (001/002) - VendorID:

I just moved my UPS over from serial to USB and found that I needed to add it to the hotplug USB list to make things work. Belkin F6C120-UNV - Bus 002 Device 004: ID 050d:0912 Belkin Components It seems to be working OK on 2.0.4 with newhidups. Attached is a patch which I think should add the appropriate device id's in the right places to the trunk code. Jon -------------- next part

Hello, all, I had been using NUT's Ubuntu package (64 bit) with no problems until upgrading to Ubuntu 11.04. Now, I get the following message when I try usbhid-ups: $ sudo /lib/nut/usbhid-ups -a mybelkin Network UPS Tools - Generic HID driver 0.35 (2.6.0) USB communication driver 0.31 Can't claim USB device [050d:1100]: could not detach kernel driver from interface 0: Operation not

Oh oops, I see you already did. -- Peter selinger wrote: > > You could send it without "submitting" it. That's the advantage of > patches - they can be discussed. There are lots of eyeballs here that > might see what's wrong. Thanks, -- Peter > > Eric S. Raymond wrote: > > > > Peter Selinger <selinger at mathstat.dal.ca>: > > > I

This model is available in AU/NZ and can work as USB or serial. It uses the cutdown Bulldog software that comes with the cheaper serial based belkin models, and they don't officially support the USB mode under Linux. Anyone managed to get this working with NUT using either serial or USB? I'd really like to get the extra functionality of the NUT tools vs the very simple setup of the

Hi I'm sending this to you as it appears that you are the person who looks after and/or supervises the code for NUT's Belkin drivers. I'm using the address you use for the Nut-upsdev mailing list ( selinger at mathstat.dal.ca ). Anyway... I have a Belkin Universal UPS and, having just upgraded my Fedora Core system from 4 to 5 and had to go back through the system RC files

Greetings! Thanks to all the developers who have made this project so far. Searching for a Linux based Belkin UPS monitor led me straight to the Network UPS Tools. I have bought a Belkin F6C900-UNV (900VA) for use on a Slackware 10.2 server to replace an older APC model that died suddenly. So far I have successfully managed to get NUT 2.0.5 compiled and configured and found that this Belkin