similar to: problem with Mustek UPS - Freebsd

Arnaud Quette wrote: > Anyhow, I would more see this as a merge of all these drivers, with > some autodetection or flag/param to switch the mfr/model and maybe > capabilities... Whatever the driver name is, a good thing would be the > name of the protocol or something generic enough, though powermust is > fine. Ok, I made some minor changes to powermust, to make it less

Hi, I'm not the maintainter for the "megatec_usb" driver (in fact, I'm no longer maintainer for the base "megatec" either), so I don't really know the status for that particular UPS. I'm forwarding this to the NUT mailing-list though. Regards, -- Carlos Rodrigues On Fri, Dec 5, 2008 at 10:30 AM, Adrian Czerniak <adrian.czerniak at becomo.com> wrote:

Hi, I'm not the maintainter for the "megatec_usb" driver (in fact, I'm no longer maintainer for the base "megatec" either), so I don't really know the status for that particular UPS. I'm forwarding this to the NUT mailing-list though. Regards, -- Carlos Rodrigues On Fri, Dec 5, 2008 at 10:30 AM, Adrian Czerniak <adrian.czerniak at becomo.com> wrote:

"mustek" is all but deprecated, so the effort should be to get powermust/megatec working. Since you have the latest development code installed, can you please run "/path/to/megatec -DDDD -a the_name_for_your_ups" (this without starting NUT normally - i.e. without upsd, upsmon, etc) and send me the output? The output should help me figure out why you are getting data stale

Hello, I'm trying to setup my UPS using the "megatec" driver, but for now without success. from what I understood, the UPS should be connected to serial port (despite being an USB UPS), so I did i. sudo upsdrvctl start Network UPS Tools - UPS driver controller 2.0.5 Network UPS Tools - Megatec protocol driver 1.5 (2.0.5) Carlos Rodrigues (c) 2003-2006 Megatec protocol UPS not

Hi folks, has anyone been successful in getting a Mustek PowerMust 500 to talk to nut? All my attempts (tried "mustek" and "powermust" as drivers) have been unsuccessful so far. Thanks for any clues. Sascha -- http://yoyodyne.ath.cx

Hello, It looks like the nut-upsuser list is momentarily down. That's why I send it to nut-upsdev list too. I have recently bought a mustek Powermust 1000VA USB (sadly not the USB P version). I have done some tests with the latest nut 2.2.0 megatec and megatec_usb drivers. Here are my feedbacks. It works quite well but is extremely noisy in battery mode (and that is not the noise of the

Hello, It looks like the nut-upsuser list is momentarily down. That's why I send it to nut-upsdev list too. I have recently bought a mustek Powermust 1000VA USB (sadly not the USB P version). I have done some tests with the latest nut 2.2.0 megatec and megatec_usb drivers. Here are my feedbacks. It works quite well but is extremely noisy in battery mode (and that is not the noise of the

Hi! I am trying to install subj, on my Bubba miniserver, that runs Debian. I am stoped now with driver test: upsdrvctl start Network UPS Tools - UPS driver controller 2.0.4 Network UPS Tools - Megatec protocol driver 1.4 (2.0.4) Carlos Rodrigues (c) 2003-2006 Unable to open : No such file or directory Things to try: - Check 'port=' in ups.conf - Check owner/permissions of all

Disclaimer: I've setup APC UPS monitoring and it works... ... but when it comes to mustek powermust 600usb (connected via com-port), I can't make it work. Got NUT installed via aptitude in ubuntu feisty and a basic setup, exactly the same as for the apc, except for the name of the ups and the corresponding section of ups.conf -- [mustek] driver = megatec port = /dev/ttyS1

Hi Stefanos, you should mail to the NUT list, and try the megatec driver, which is only available from subversion for the moment (but should be included in the next stable release). Carlos might give you some help with this driver. Arnaud Quette -- Linux / Unix Expert - MGE UPS SYSTEMS - R&D Dpt Network UPS Tools (NUT) Project Leader - http://www.networkupstools.org/ Debian Developer -

Hi, a few days ago, I bought some of those Mustek UPSes that have both a serial and a USB connector. Currently only the serial port is supported by the megatec driver. This works fine so far. Now I have seen there is a megatec_usb driver, which currently only supports 2 other UPSes. How can I help to find out whether the PowerMust might actually work with the megatec_usb driver? -- Regards,

A non-text attachment was scrubbed... Name: not available Type: application/pgp-signature Size: 188 bytes Desc: not available Url : http://lists.alioth.debian.org/pipermail/nut-upsdev/attachments/20071124/3ceb35d2/attachment.pgp

I Carlos I'm troubleshooting this problem with the driver you wrote: My Ups is Powermust 800 The OB-LB status cames too late to shutdown my Suse 10 system, I searched to find out how to change the state to LB when battery is at almost 30%. Only in this way I'll be sure the pc will shutdown correctly Please tell me how to do so Thank You so much I'll be waiting Best Regards

NUT recently stopped working on my debian. I'm not sure which upgrade broke it. ups.conf: [mustek] driver = megatec port = /dev/ttyS0 desc = "mustek ups" # upsd -DDDD Network UPS Tools upsd 2.4.1 listen_add: added ::1:3493 listen_add: added 127.0.0.1:3493 setuptcp: try to bind to 127.0.0.1 port 3493 listening on 127.0.0.1 port 3493 setuptcp: try to bind

Hi all, Currently, the "megatec" driver only supports UPSes which have a serial (RS232) interface. However, I'm under the impression that most of the models that speak the megatec protocol, and have an USB interface, just have a standard serial-to-USB converter inside. This being the case, there should be a "/dev/ttyUSBx" device which the megatec driver could use just as

Hi all, Currently, the "megatec" driver only supports UPSes which have a serial (RS232) interface. However, I'm under the impression that most of the models that speak the megatec protocol, and have an USB interface, just have a standard serial-to-USB converter inside. This being the case, there should be a "/dev/ttyUSBx" device which the megatec driver could use just as

Hello, We are using the equipment "MUSTEK PowerMust 3000 NetGuard RM". That is using Megatec protocol. But unfortunately not all the data can be viewed correctly when dumping from utility "upsc". For example: upsbox# upsc mustek at localhost battery.voltage: 108.00 battery.voltage.nominal: 96.0 driver.name: megatec driver.parameter.pollinterval: 2 driver.parameter.port:

On Feb 11, 2008 5:30 PM, Marcio Gomes <mpg at microlink.com.br> wrote: > I change the if in [OFF] detect state to, in original way, if you send a > reset.watchdog, the UPS goes > to OFF state in clients, but it is not correct, because UPS is OL and > Shutdown are in progress, but > the power is not OFF First of all, thanks for the patch. But I have a few comments: Are you

I had some free time this weekend, and made some long overdue changes to "megatec". The thing is, these changes lead to a couple of questions that I must ask before I go on and "svn commit" them: 1) The blazer, fentonups, esupssmart, ippon, sms and mustek drivers are now completely covered and all of their functionality should now be present in megatec, and also every model