similar to: KX-TDA console & Wine

Thank you for response. So a "standard" quad bri card can serve the KX-TD1232, no need for anyt special fxs similar equipment. Would like not to invest much more money into the Panasonic, I wan't it out :P BR Amund -----Opprinnelig melding----- Fra: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] P? vegne av Peter Svensson Sendt: 14. juni

I am not familiar with that phone. Is it single pair? -----Original Message----- From: broadbandvoice@comcast.net [mailto:broadbandvoice@comcast.net] Sent: Sat 4/22/2006 12:13 PM To: asterisk-users@lists.digium.com Cc: Subject: [Asterisk-Users] PANASONIC KX-TS208W - Speakerphone IncompatibleWith Asterisk 1.2.3 I'm using Asterisk 1.2.3 and PANASONIC KX-TS208W - Speakerphone does not work

Hello, Is it possible to connect the Panasonic KX-T7665 IP phone to Asterisk? Kind regards Michael Felder IT Medic Australia Pty. Ltd. P: 03 9557 2213 F: 03 9557 2214 M: 0419 568 217 E: Michael@ITMedic.com.au http://www.ITMedic.com.au Keeping your computer systems healthy.

Hi all, There is someone with some experience interconnecting a Panasonic digital PBX (KX-TD1232) with Asterisk? Thank you and best regards, Dan

I'm using Asterisk 1.2.3 and PANASONIC KX-TS208W - Speakerphone does not work with it. It works fine when you pick up the handset. Anyone experinced this problem before, the speaker works fine with Verizon line. The phone is behind a Linsys router RT31P2. -------------- next part -------------- An HTML attachment was scrubbed... URL:

Has anybody have any experience using the KX-TGP500 Cordless DEC 6.0 "System" with asterisk ? I run a small asterisk server at home using two SPA3102s, and thinking of upgrading my cordless analog phones to something a little newer. -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hello, We use Asterisk with PAP2 and today we connected the FXS ports of PAP2 to CO ports of our Panasonic KX-TD1232. Problem is that Panasonic doesn't ring - that is doesn't ring every time the PAP2 is ringing. When we reset either Asterisk or the PAP2 it usually rings, but after couple of minutes it stops and only the automatic operator is answering - after 2 rings. We tried changing

If Someone did that, How I connect extensions.conf with this type of Hybrid system to work with asterisk inside this schema: PSTN--->PANASONIC KX <------> Asterisk | |--------->send internal call Thanks.

hi everyone, Is it possible to serially connect my panasonic KX-TD1232 with a Linux box(Asterisk installed) and have it working? -- P. K. kakarizz@fastmail.fm

Anyone have any luck with connecting Asterisk to the Panasonic KX-TD500. I have Asterisk connected via crossover to the TE110P. We are able to make internal calls into the Asterisk Box but the PBX vendor (I know nothing about the KX-TD500) tells us it is not possible route DID over the trunk. I find this hard to believe. Anyone have any luck with this? Thanks! -------------- next part

Sorry someone screwing with permissions on my server bounced the 2 days worth of email after I posted this, any and all those lovely people who replied with suggestions from my post could you sent them again :-) James -----Original Message----- From: James Bean On Behalf Of Asterisk Mailing List Sent: Tuesday, 30 May 2006 12:54 PM To: 'Asterisk Users Mailing List - Non-Commercial

I know people have been having problems with Rift and wine after patch 1.2 but after looking at some of the error messages the ones I'm getting aren't the same but similar. After fighting to get wine past the direct X not up to date error for 3 days and finally succeeding in getting it to work. My game goes past the patch part and into 'start play' with out getting a direct x out

Panasonic PBX KX-TDA600 it doesn't support SIP protocol for VoIP technology it only support H323 Trunk through 4 or 16 channels gateway card and TDM technology with ISDN BRI and PRI card. Mc GRATH Ricardo

Hello Everyone... I work as a sys admin for a small college in North West PA. Recently, a group on campus has stareted an animation club, and are looking into purchasing MAYA for linux.... very expensive. I thought I might be able to help them out and set up MAYA PLE through wine... I get WINE setup and can run IE6, however when i run the maye.exe installer, the installer launches, hangs,

Hello We have around 50 phones in our company, and I am playing with the thought to gradually go over to using sip services and ip-phones internally. However at first I would liked the Asterisk just to sit between the phone line and the Panaosnic, so I can take out one lin/number at a time to use ip phones. I am new to Asterisk, and haven't done much configuring of the PBX either. So I also

Hi, I have noticed the 'ssl_cipher_list' directive in the 1.0-test snapshots which is not in 0.99. It's default value seems to be "all:!low". However, this would not be compatible with openssl's cipher listing format. Thus, I would vote to change it's format to be openssl compatible. To be compatible, it has to be changed to "ALL:!LOW" (just upercased in

Hi All, Just a quick one. Some turkey has bought a kyocera 680 and we have to set it up for samba print sharing. We have about 35 other HP, Lexmark, and other things working a treat on this server so I know it's all working. When I try to upload the driver for the kyocera it uploads fine from my windoze box and everything looks sweet, I apply and I get the extra tabs as expected for

Dear Jan, Thank you very much for your excellent description of the problem and the self-contained test code. This is a problem that I've been meaning to either document better or solve for some time. The root of the problem is with the builtin S-Plus terms.inner function: > attr(terms.inner(asthma ~ pol(age,kx) + smok),'variables') expression(age, kx, smok) You can see that

Hi When I run a program I've written with Delphi7, I get several of the following messages: fixme:imm:ImmReleaseContext (0x10020, 0x403b9e80): stub . . . The program works - but is there anything I can do to avoid these messages? Rainer -- Rainer M. Krug, Dipl. Phys. (Germany), MSc Conservation Biology (UCT) Department of Conservation Ecology and Entomology University of Stellenbosch

I am trying to get Spore to work under WINE. I have installed the game plus the Galactic Adventures expansion without any problems, but when I try to run it I get a black screen and an error box stating "The program SporeApp.exe has encountered a serious problem and need to exit" Below is the output from the terminal. Any ideas on what might be causing this. I have update the graphics