similar to: Routing multiple conntections to the same ISP

helo again. I think this question i am asking is worth: we know that pppoe-server creates a pppX device on each connection done to it. So, when i have to shape, i have to shape each pppX connection device on itself alone. What i know is that the borrowing method on one device by itself, e.g. ppp0, alone using HTB or the like. this means that i have to create for another device, e.g. ppp1,

HI folks, I have a linux router connected to two separate internet connection from an ISP. There is a third interface ( ip -> 192.168.1.1 ) in the router connected to the local network. Configured the routing tables and added the rules and everything seems to be working fine from the routing box. Traceroute to external internet sites reveal that traffic is being routed correctly and

Hi, I have the following situation: 1 gateway box with 2 WAN interfaces (eth1 and eth2). 1 LAN interface eth0 default gateway is eth2 I want to route all traffic with destination protocol tcp 22 (ssh) NOT over the default gateway eth2 but force them to find it''s route over eth1. All other traffic must go the normal way over eth2. Is this possible with tc or an other tool? --

Hi Here is a short description of my network: ppp0 (adsl) ppp1 (adsl) | | | | --------------------- | Router | | Firewall | | MASQUERAD | | DNAT | | | | eth0 | --------------------- | | | ---------------------- |

I need basic PPPoE startup help. adsl-start DID bring up my PPPoE link (ppp0) to my ISP over eth0 via the DSL modem/bridge. My IPv4 CIDR block is routing and Shorewall is doing the firewalling. But shorewall has to be started after ppp0 is up and working. For now this means running shorewall restart (or start?). Shorewall 4.2 will have a way to restart shorewall without recompiling, I

I have two adsl lines on my linux firewall box and i want to do some load balance between them...i tried a lot of different things, but it isn´t working...Following the instructions of http://lartc.org/howto/lartc.rpdb.multiple-links.html i used the configuration above. using "iptraf" I can see some few packets using the ppp1 connection, but almost all the packets use ppp0 connection.

Hello Shorewall list, I''m a happy Shorewall user since a few years now and everything works fine for me except one thing that I try to implement since a week, the multi-isp. I''ve downloaded the 2.4.0 Stable release yesterday and tried the RC2 since a week. My config is a Debian running a kernel 2.4.27 home made with the CONNMARK.diff patch applied I''m using 2 ISP,

i''ve read your http://lartc.org/howto/lartc.rpdb.multiple-links.html article as well as Advanced IP Routing (esp. chapter 10.4) and still unable to make this thing work. am i that helpless? :) is there anyone to guide me through the multiple ISP setup? into details. i got 2 dsl connections from different ISPs (A and B), both connections use PPPoE, both got assigned with dynamic IPs

Hi, I currently connect to my ISP via my adsl modem in bridge mode and PPPoE. I am due to put a second PPPoE ISP onto my firewall box which will give me ppp0 (general) and ppp1 (static leased line). The static leased line will run a number of services on its static IP and it is therefore imperative to make sure rules defined for the static line are assigned to the correct interface. I need this to

Hello all, We have two ADSL lines configured on a single box, hence interfaces ppp0 & ppp1. Is there a way to route packets to ppp0, say based on destination port 80 & other traffic like voice through ppp1? Thanks.

Hi, Thanks for the reply. Thats where the problem starts. If I set ppp0 as the default gw the internet doesnt work anymore. This is how im doing it... route del default route add default gw 217.32.81.74 dev ppp0 if I put it back to ppp1... route del default route add default gw 217.32.68.73 dev ppp1 It works fine again. Whats up with that? Cheers, Chris ----- Original Message

Hi, I''ve set up a Linux box with redhat on to act as an internet gateway and I''m running into a few problems. Its got two adsl modems connected to it, both connected to seperate 512kbs lines. Now I''ve followed the simple source routing in the advanced routing howto to the letter but it doesnt work. I''ve got it autoconnecting on startup and redhat puts ppp1

Hi. The task: 1. There 3 servers and a router with 2 PPPoE connections (let call them: ppp0, ppp1). 2. There are several groups of Inet-clients to be served (Servers, Clients and Club). 3. The task is: - to route Club through the ppp1; - to Servers and Clients through ppp0; (Next is reproduced from memory and may be slightly incorrect) router # netstat -nr Kernel IP routing table

Hi ! Recently i switched my internet provider, to get more speed but another braindead setup regarding public ip addresses. I now have 4 PPTP Tunnel available, of which i''m using one as the gateway ip doing masquerading to other machines in my local lan, excluding three other machines, which i would like to use 1:1 nat to get them a direct access to one of the pptp tunnels. I was

Hi, I have a linux box with two dsl modems on it (connection is done via pppoe), I''m trying to route default traffic on the primary connection (ppp0) and mail traffic on another one (ppp1). This traffic will come from the localhost. I run Slackware 9.1 (Kernel 2.4.22), recompiled with necessary options for using iproute2. According to the advanced routing howto, I did the following

Hi, can anyone help me with this problem i''ve got! I have a problem with routing on my Mandrake 7.2 Linux Box i was wondering if you could help me with. I live in Australia and as broadband access isn''t very available at the moment, i have 2 modems to dialup to my isp (dynamic ips assigned) to increase my bandwidth at an affordable level. What currently happens is i have a

My Internet gateway is using ADSL PPPoE connection with dynamic public IP assigned by ISP. My Internet gateway is Redhat AS3 U2, shorewall 2.0.9 As my ISP provided 4 simultaneous pppoe dailup connection for the same physical adsl line. My linux server can be configured for multiple pppoe connection i.e. ppp0, ppp1, ppp2, ppp3 Is it possible of shorewall to assigned say ppp0''s IP is

Hello Lartc Mailing List: Been working on something the last week and a half and ALMOST have it working.., just need a few pointers from the wizards on this mailing list to nail it. Ok, my setup is a hub and spoke arrangement, hub is Cisco 2821 with IOS 12.4. Spokes are ruggencom RX1000 routers, Debian based with the following versions installed: rx1000test:~# uname -a Linux rx1000test

Hi folks, i spent my whole day trying to set up my linux router using load balancing with multiple uplinks. I mainly focused on the nano howto, but somewhere I have a big mistake within my head. Basically the load-balancing is working, but not on a per-connection basis - just on a per packet basis. Practically this is not usable of course <g> But as far as I understood it should work..

The current thread on the User''s List entitled "Multi-ISP in 2.4.0" includes the following tcrules file: ############################################################################ ## #MARK SOURCE DEST PROTO PORT(S) CLIENT USER TEST # PORT(S) 201:P eth2 ppp1