similar to: load balancing: per route or per interface?

hi all, i am setting up a load balancing netwrok with failover, i have applied julian patch, but whenever i try to traceroute from any client node, it gives me two entries for that destination, but i get different interface for that entries, so it doesn''t forward my requests, i have done masquerading for client nodes, the ip rule/route are as follows, ip rule add prio 222 table

Hi list! I have a LAN server with Gentoo Linux. It''s a Pentium III at 1000 MHz with 256 MB SDRAM. I''ve implemented a QoS solution with HTB and SFQ. Here is the diagram: _______________________________________________________________________ 1:--+----1:1 - [ counter-strike & icmp ] rate=1Mbit; ceil=1Mbit; | prio 0; (u32 filter

Hi! I''ve 5 DSL routers and a linux router in a switch. The linux router is doing NAT for a LAN network, but it freezes when I set up load balancing with this command: ip route add default proto static\ nexthop via 192.168.1.10 dev eth1\ nexthop via 192.168.1.20 dev eth1\ nexthop via 192.168.1.30 dev eth1\ nexthop via 192.168.1.40 dev eth1\ nexthop

hi i''m using htb + u32 filters, and i was wondering if there is something one can optimize at this stage. i have a lot of filters (~ 50.000 / interface, and there are two interfaces), and around 4500 classes / interface. the traffic going through this machine is something around 210-230mbit/s at 50kpps. as you can imagine, the load is pretty high. in fact (as it''s a dual xeon at

I''m currently trying to optimize a linux machine which acts as a Layer 3 router of RTP H.263 video. Occassionally I''ll get delays related to layer 2 wireless retries, thus rendering the video on the recieving end stale/useless. Is there way to optimize a linux machine to route realtime video? In my case, losing a few frames of H.263 is better than having the video delayed

Has anyone had successfully installed more then two digium wildcards in the same machine? I'm going for four. thanks Shoval Tomer, IT Manager, SofTov Advanced Systems, Ltd. Office: +972-3-9230686 ext. 179 Fax: +972-3-9216642 Mobile: +972-54-8000200

Dear all Lartc, I try to split my Internet access to my 2 ISP with 1 linux (GNU/Debian sarge) 3 NIC router, I want all my users conneted with ISP1 and just some IP connected with ISP2 Here is my configuration: Internal network: 10.117.71.0/24 Interface eth0 ISP1: IP for my linux box: 1.2.3.4/29 Interface: eth1 Gateway: 1.2.3.5 ISP2: IP for my

Hello everybody, After going through multiple posts on Internet and trying different things I can't seems get zaptel wcfxo loaded on the server correctly. I run dual P3 500 Mhz box. After reading README.udev I put a file 60-zaptel.rules /etc/udev/rules.d # Section for zaptel device KERNEL="zapctl", NAME="zap/ctl" KERNEL="zaptimer",

Hi, my company have just bought new network and I have question about one problem. As in topic we must use few completely different dsl''s and balance traffic between them. 2M/0,5M 4Mb/0,5M 8M/0,5M M=Mb/s I''ve never done such thing before so I have doubts how it will work. If the links are symmetric 2/2 4/4 8/8 there is no problem because with weights I can compensate the

Hi All, This is out of the topic question, but I''m hoping that you can help me. If for example I''m going to install a Fedora 4 64-bit with 8 to 12 Gig of physical memory, how much swap file of directory do I need to create? Thank you very much, Wennie

I ran some iperf tests today and it looks like the etherbridge is the limiting factor on throughput. In the beforetime, I saw great throughput to the VMs; over 800 Mbps. With the bridge, the numbers are in the 400s somewhere. Is this the speed I can expect from the bridge? Is there some tuning I should try, or another way to get more bandwidth into the VMs? This is with xen-2.0, 2.4.27-xen0

Recent SUP. Installed on Dell PowerEdge 4600. Getting tons of: Sep 30 12:23:16 zige /kernel: bge0: gigabit link up Sep 30 12:23:46 zige last message repeated 98 times Also getting some TCP retransmits. This causes noticable delays in pretty much everything I do now. Not a problem prior to the SUP. I was on 4.8-STABLE before. When pulling/replacing cables, it went into a mode where it would

Hi. I gave up with the IBM NetFinity, so I'm going to buy new hardware. I'm going to install: 1-)One X100P (1 FXO module) 2-)One TDM03B (3 FXO modules) I'll have the 4 FXO channels busy almost all the time, and I would like quality to be as good as possible without going to the high-level hardware. I would like to learn of some tested configurations (I've heard of problems

Can anybody tell me the difference between a TE410P and a TE405P? Is it JUST the 5v vs 3.3v pcis slot spec, or is there some thing else? </edg>

Hello! Has anyone gotten 4.9R to recognize the "ServerWorks CSB6" ATA controller on a Dell 600SC? How about installing 5.2R on a 600SC? 5.2R recognizes the said controller, but it corrupts data. -- eof

Hi, I received a bug report against BerkeleyDB 4 that may not be BerkeleyDB related, but a problem with FreeBSD or specific hardware in general. Jie Song (CC'd) reported that writing files with BerkeleyDB (no threading or something) on his ServerWorks machine causes data corruption (detected by BerkeleyDB 4.0 library functions) when the file sizes grow beyond 350 MB. For details, see PR

I have a new device that takes measurements anywhere from every second, to every 15 minutes (depending on changes). The matrix has a date, time and Y column (Y is the measurement). For three days it is 25,000 rows. How do I average the measurements by every 30 minutes so my matrix is 48 rows per day? I have been working on this and cannot figure out a simple method. Any ideas? Thank you. ----- In

Hi! I am trying to export a PCI device (an AVM Fritzcard PCI ISDN card...) to a domU but when starting my domU I am getting this error: "pciback pci-4-0: 22 Couldn''t locate PCI device (0000:00:06.0)! perhaps already in-use?" My system is running both debian etch in dom0 and domU... Below you can find (hopefully) all important information... Sincerely, Gaubatz Patrick

Hello lists, I,ve compaq ML350 with 2 Xeon 2.4 GHZ and FreeBSD 5.0 RELEASE installed and working very fine about 4 mounts. The machine running GENERIC kernel samba and firebird database server with no problems until at begining of this week, in morning machine freezes with no responce iven in conconsole, no responce from network (pinging) no responce on console (key pressing) the only way to get

Hi, Thanks to everyone involved in the Xen project. I think it is great and can''t wait to get my hands dirty with it. In the meantime, I cannot boot Dom0 on an ibm x335 and I am not sure what the problem is. Any insights are welcome. Here is what my grub.conf file looks like: title Fedora Core (2.6.8-1.521) root (hd0,0) kernel /vmlinuz-2.6.8-1.521 ro root=/dev/sda9