similar to: Configuring several route tables for the same network interface

-----Original Message----- From: Salim S I [mailto:salim.si@cipherium.com.tw] Sent: Thursday, May 10, 2007 5:22 PM To: ''Francis Brosnan Blazquez'' Subject: RE: [LARTC] Load balancing using connmark "I think the main advantage of shorewall solution is that it applies connmark to incoming packets from the wan as you point, leaving load balancing to outgoing connections to the

Hi, I''ve been implementing a load balancing solution using CONNMARK, based on solution described by Luciano Ruete at [1]. Gracias por el post y por apuntar en la dirección correcta Luciano! Once implemented, I''ve found that due to some reason packets aren''t properly marked (or improperly remarked) and sent out using the wrong interface. My topo setup is:

I''m working with LEAF boxes as gateway machines. I''m trying to implement Proxy-ARP to build a bandwidth manager for my network. I''ve gone as per the lartc howto to implement a transparent bridge in an existing network and plan to put in my tc script after this. I''m configuring the box as a standalone one before plugging it into the network. I''m getting

I am sharing out ZFS ISCSI luns to my Mac. When copying large files, the network will hang in the middle of the transfer and the LUN will become unavailable until I plumb the NIC. This issue appears to only occur only when I am reading files (ie..syncing an ipod) and not writing (I''m not 100% sure though). When I snoop the interface I notice a bunch of ARP lookups. Any ideas? Thanks in

Hello all, I do not read C very well (especially kernel C). Though I have tried to muddle my way through an understanding of what''s going on in fib_hash.c, fib_rules.c, and route.c, I have not succeeded to my satisfaction, hence my post. I''m trying to document the general process of route selection, and have come up with the following overview. Could somebody point out any

Hello all, Basically my problem is how can i access a virtual machine from local network. I am able to do so from the host PC put not from other PC's on the same network. here is my what i did so far (http://wiki.libvirt.org/page/Networking#NAT_forwarding_.28aka_.22virtual_networks.22.29) cat '/etc/libvirt/qemu/networks/default.xml' <network>

Hi folks, Sorry to trouble you all - I'm having some trouble getting tincd up and running - I suspect I'm having problems with subnets. Any help would relaly be appreciated! At the moment I'm trying to get two linux boxes, both of which are running as NAT routers for their respective networks to talk. My goal is to allow staff to connect to the corporate network from their laptops

Hello i resolve the installation of the package rimage following the indications by Andy Jacobson in the list osx@tazman.princeton.edu the trick is using R CMD INSTALL --configure-vars='LDFLAGS=-L/sw/lib CPPFLAGS=-I/sw/include' rimage_0.5-7.tar.gz the packages fftw2.1.5 and libjpeg were installed via Fink. Thanks for Prof. Brian Ripley for ththe response and hope this can help

Hello all, I am going through the LARTC howto to understand how the iproute2 works. But some concepts like Policy Routing, RPDB etc are not clear to me. I am pretty new to iproute, beeing using route command for long... From what I understand 1. rules (ip rule) tell how to select packets for routing and route (ip route) tell where to route the selected packets. 2. A collection of rules is

Hi, I''m sorry for "novice"-level question, but I hope your expert advice will save me many painful hours running after my own tail... Let assume I have Linux box with eth0, eth1 and eth2 interfaces. Each one has IP assigned from different network. By default, IP address associated with eth0 is chosen as default routing. My application creates thee TCP sockets and explicitly

Hi! In our students'' hostel we have 6 DSL lines (dialups to different providers); we have set up a linux box (currently running 2.6.11-rc2-mm2, but the problem described hereafter also applies to previous 2.6-series kernels) with help from http://lartc.org/howto/lartc.rpdb.multiple-links.html#AEN298 Our Setup looks like this: 10.0.0.0/8 10.70.255.1 +----------+ +-----------+ |

OK I have sufficient evidence now that my split route ( multipath routing ) is inducing kernel panic and also frequent connection lost. The split route may not be the culprit but I can safely say that without using the split route, my system is perfectly stable. I have set up the split route according to http://www.tldp.org/HOWTO/Adv-Routing-HOWTO/lartc.rpdb.multiple-links.html I could use

Hi, I''ve set up a Linux box with redhat on to act as an internet gateway and I''m running into a few problems. Its got two adsl modems connected to it, both connected to seperate 512kbs lines. Now I''ve followed the simple source routing in the advanced routing howto to the letter but it doesnt work. I''ve got it autoconnecting on startup and redhat puts ppp1

Hello, I have been failing to configure the pware compiled version of SAMBA 3.5.11, prepared for AIX 6.1, upon an AIX 7.1 system to work in an ADS domain and I wondered if anyone might be able to advise on what I should do next. I am trying to setup the AIX server as a file server within the ADS domain so that users can be recognised in an SSO configuration. I am pretty confident that the krb

Hi list, I''m new to this list, I just subscribed because I have some ackward about IPRoute2. First, while playing with NetFilter'' "MARK" target, I met a weird behaviour once I tried to use this marks in the RPDB : the packets where successfully marked, but it seemed that RPDB didn''t succed in matching them (for those who already know the answer, I only used

https://bugzilla.netfilter.org/bugzilla/show_bug.cgi?id=452 Summary: DNAT to internal network don't work with source routing and 2 uplinks Product: netfilter/iptables Version: linux-2.6.x Platform: i386 OS/Version: Debian GNU/Linux Status: NEW Severity: normal Priority: P2

Dear all, In my understanding of Shorewall, I''ve tryied a setup in order to dynamicaly allow/prohibit internet access for a subset of system located on the LAN side. i.e: shorewall.conf: DYNAMIC_ZONES=Yes zones: test Testing Tests on going (dynamic) users Users Users on the LAN lan LAN Local Area Network net Inet Internet interfaces: net eth0 detect lan eth1 detect hosts:

I have two adsl lines on my linux firewall box and i want to do some load balance between them...i tried a lot of different things, but it isn´t working...Following the instructions of http://lartc.org/howto/lartc.rpdb.multiple-links.html i used the configuration above. using "iptraf" I can see some few packets using the ppp1 connection, but almost all the packets use ppp0 connection.

Hello, Where can I find a link (or docs) to *working* network config for xen 4.1.2? My tests (s. below) were not successful. Thank you in advance for any hints. Regards, Mark # --- root@xen411dom0:~# cat /etc/network/interfaces # Used by ifup(8) and ifdown(8). See the interfaces(5) manpage or # /usr/share/doc/ifupdown/examples for more information. auto lo iface lo inet loopback auto bond0

Hello All, I have a linux box running with three NIC''s, I have used brctl tool to configure this box as a bridge, i have given it ONE logical ipaddres, Every thing is working fine, but now i am required to configure the same bridge as a LOAD BALANCER.... On some googling i found the following link http://lartc.org/howto/lartc.rpdb.multiple-links.html This HOWTO requires me to have one