similar to: Can't match DSCP CS6 and CS7

what are these error messages: Unknown IE 40 (cs6, Unknown Information Element)

Greetings, I am porting the openssh-portable 6.8 release to the HP NonStop (NSE) platform. Prior versions were no real problem, with minor tweeks. However, with the inclusion of regress/netcat.c, which depends on arpa/telnet.h, we have an issue. Unfortunately, the platform does not have this file, nor anything like it - telnet is done rather differently. We do have a version of netcat (0.7.1

I have a new APC Smart-UPS SUA2200RM2U. I've had no success with the manufacturer's PowerChute software and smart signaling, so I have decided to try NUT. The smartups driver can't make contact through the serial port. Since this is rack-mounted, it comes with a 940-1524 serial cable. As far as I can tell, this is supposed to work with smart signaling. Here's my ups.conf:

root at cs6:~# zpool import pool: content3 id: 14184872052409584084 state: FAULTED status: The pool metadata is corrupted. action: The pool cannot be imported due to damaged devices or data. The pool may be active on another system, but can be imported using the ''-f'' flag. see: http://www.sun.com/msg/ZFS-8000-72 config: content3

Hello, Several people report that outgoing phone calls to our clients sound muffled, like they are talking underwater. Reported for both the Snom 870, and the polycom ip650. Incoming calls sound ok. Could this be a codec problem? My dialplan looks like: [general] port = 5060 bindaddr = 0.0.0.0 srvlookup = no tos_sip = cs7 tos_audio = ef registertimeout = 1 relaxdtmf = yes context =

I am hoping someone could shed some light and point me in the right direction? I'm attempting to get callerid work between an Avaya Definity PBX and Asterisk via TE110P connected via T1/PRI Crossover PRI. From the Definity side I've searched endlessly and came with an example which we modeled as close as we can, but still no luck. While doing PRI intense debug span 1 in I see a couple

You should run the 4ESS protocol ("a" on the Definity command "change DS1 board#) as the Definity may not send Display Name for the NI-2 protocol (settings "b" or "d") Remember to make the Asterisk zapata settings consistent with the Definity. On the Definity trunk group form Page 1, change "Codeset to send Display" to "0 (zero)", also make

Hi, I have this setup: E1 PRI PSTN -- Asterisk -- Alcatel PBX - analog phones Can someone tell me what's wrong with this call initiating from an analog phone connected to Alcatel PBX? It dies with NOANSWER but all works if I call other destination numbers. Dialplan is a simple Dial(zap/g1/0984465691) statement. At the end you'll find also zapata.conf.

Hi all, after a half day searching for an error, sniffing and upgrading to the newest shorewall version I give up and the problem to you. I have following configuration in my /etc/shorewall/masq: #INTERFACE SOURCE ADDRESS vlan7::10.231.0.0/16 192.168.222.0/24 10.231.113.30 vlan7 192.168.222.0/24 10.1.0.38 Towards a

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 As I pointed out to Wilson in a private message, this appears to show that no other connection requests (other than port 3000) are being sent from the client to the server (or at least no other connection requests are being received by the Shorewall box). Wilson: Are you sure that the client is supposed to open port 3001 on the server and not the

As i can see, if i use Shorewall tools for blocking client traffic ('blacklist' file, 'shorewall drop') it has effect only for new connections but existed don't blocks. Can i with Shorewall stop ALL traffic for definite clients? Alex ----------- IRR.BY ('Из рук в руки – Онлайн') – крупнейший в Беларуси сайт частных объявлений. http://irr.by

Thanks to some of the guys on #samba-technical (obnox in particular!), I now have a working samba configuration. The environment: In our setup each user has an entry in both openldap (no samba schemes) and AD. Each account has the same name and even has a Unix UID entry in AD. Our users ssh into Linux boxes, authenticating off of openldap. Files are shared via samba. Due to the account

I can use DSMARK to mark on the Egress side. Is there a way to mark/change the DSCP value of an incoming packet on the ingress side? Thanks. Jon Flechsenhaar Boeing WNW Team Network Services (714)-762-1231 202-E7

I have this setup: (PSTN E1 PRI) -- Asterisk -- (crosscable) -- Alcatel PBX --- analog phones and a few of VoIP phones directly connected to Asterisk. Calling a number (just one!) - an automatic responder (IVR) - from VoIP phones works, from analog phones doesn't work: NOANSWER after a few seconds. I'm using no 'r' in dial options (this caused a problem with an IVR some time

I'm not a big fan of Line Side for Asterisk applications.... the individual channels have to be reserved (reminds me of the "old" days in telephony) and I don't like that... rather make it a tie trunk and use ARS/AAR routing in the Definity... much more general application. This also makes routing on the Asterisk a lot simpler. Easy to make the changes.... will advise if

The Wine development release 1.7.41 is now available. What's new in this release (see below for details): - More Known Folders supported in the shell. - Some more support for kernel job objects. - More MSI patches improvements. - Some theming fixes. - Various bug fixes. The source is available from the following locations:

The Wine development release 2.15 is now available. What's new in this release (see below for details): - Support for AES encryption. - Improved Bezier support in Direct2D. - Chunked transfer improvements in WinInet. - Various bug fixes. The source is available from the following locations: http://dl.winehq.org/wine/source/2.x/wine-2.15.tar.xz

The Wine development release 2.16 is now available. What's new in this release (see below for details): - Support for pasting metafiles in RichEdit. - Better support for grayscale PNG images. - Support for safety features in library loading. - Better handling of transforms in GdiPlus. - Rendering improvements in DirectWrite. - Various bug fixes. The source is available from the

The Wine development release 1.9.10 is now available. What's new in this release (see below for details): - High resolution ("Retina") rendering option on Mac OS X. - More compatible directory enumeration. - A number of C++ runtime fixes. - Video output improvements. - Various bug fixes. The source is available from the following locations:

The Wine development release 1.7.35 is now available. What's new in this release (see below for details): - Beginnings of support for OpenGL core contexts. - Initial support for glyph placement in DirectWrite. - Some more WBEM objects. - Various bug fixes. The source is available from the following locations: http://prdownloads.sourceforge.net/wine/wine-1.7.35.tar.bz2