similar to: Messages related libvirtd and bond

Hi! Is it HTB fully compatible with BOND interface? I have this setup (mode= fault tolerance) : BOND0 -> ETH0 + ETH1 BOND1 -> ETH2 + ETH3 ( http://www.kernel.org/pub/linux/kernel/people/marcelo/linux-2.4/Documentation/networking/bonding.txt ) HTB work very well with Class over BOND0. If I add Class for BOND1 it generate balance errors. Also with HTB.init

# modinfo ixgbe filename: /lib/modules/2.6.32-431.el6.x86_64/kernel/drivers/net/ixgbe/ixgbe.ko version: 3.15.1-k license: GPL description: Intel(R) 10 Gigabit PCI Express Network Driver author: Intel Corporation, <linux.nics at intel.com> srcversion: B390E9D9904338B52C2E361 I have updated this to 3.18.7-1 as well, same results # ifconfig bond1 |grep error

Dear CentOS, I think i found a "bug" in the /etc/sysconfig/network-scripts/ifup-eth script of CentOS 5.2. i can post the my changed ifup-eth script if you want. Am I the first one with this problem? Situation: - eth2 and eth3 should be in bond1 interface - bond1 should be an interface of bridge named "iscsi" the problem is that the brctl addif command in ifup-eth gets

Hi, I've using linux bonding in active-backup mode to combine two pairs of GigE NICs (eth0/eth1, eth2/eth3) into two logical bonds (bond0/bond1). All is working fine. However, I would like to specify a primary interface for each bond. This means I need to specify different options to the bonding module for each bond. I have tried every conceivable incantation of options and cannot get the

Hi List, We're using bonding to create bond0 with 2 NICs, and noticing that CentOS 5 2.6.18-8.1.14.el5 (and presumably older) creates bond1 as well. I'd like to remove bond1 from the system, so that our monitoring scripts don't pick it up, except for those machines that actually do have a bond1. So... how does one remove bond1? Thanks! Misc info below of configuration and

Hi, Fedora got a bug report https://bugzilla.redhat.com/show_bug.cgi?id=1401612 In qemu with two virtio-net interfaces: $ ip l ... 5: ens14: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000 link/ether 52:54:00:e9:64:41 brd ff:ff:ff:ff:ff:ff 6: ens15: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000

Hi, Fedora got a bug report https://bugzilla.redhat.com/show_bug.cgi?id=1401612 In qemu with two virtio-net interfaces: $ ip l ... 5: ens14: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000 link/ether 52:54:00:e9:64:41 brd ff:ff:ff:ff:ff:ff 6: ens15: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000

Hi, Sometimes, I found one of my Mellanox NIC renamed to rename6, instead of eth1. The right names of NICs in my system should be: eth0 Mellanox NIC eth1 Mellanox NIC eth2 Intel NIC eth3 Intel NIC eth4 Intel NIC eth5 Intel NIC eth0 and eth1 will combined as bond1 with mode 4. However, the current names are: eth0 Mellanox

Hai, That bond0 interface, you might want to change that the interface name to bond1 Depending on the bonding settings, you might have hit a reserved name. I lots my docu on that but i know i configured a bond1 because bond0 didn work right. And then check these. wbinfo -pPt ( or wbinfo -p && wbinfo -P && wbinfo -t ) wbinfo --sids-to-unix-ids S-1-22-2-10513 wbinfo -D

Hi, I am facing issues after upgrading one of the server from rhel5.5. (86_64) to latest rhel5.7 (86_64). The server is under trunk configuraion. I have set the network bridge as follows: #!/bin/bash vconfig set_name_type DEV_PLUS_VID_NO_PAD dir=$(dirname " $0" /etc/xen/scripts/network-bridge $@ vifnum=1 bridge=xenbr2 netdev=bond0.10 /etc/xen/scripts/network-bridge $@

Hello, Could someone tell me, how can I select from a dataframe only those columns whose names contain a certain text? For example, if the column names are "Bond1.Creditclass","Bond1.Price","Bond2.Creditclass","Bond2.Price", how do I select only the columns corresponding to Bond1? Thanks a lot, Mihai [[alternative HTML version deleted]]

Hi All I have two bond interfaces namely, bond0 and bond1. bond0 has two ethernet interfaces associated with it and bond1 also has two ethernet interfaces associated with it. Now i create a bridge interface namely br20 (20 being the VLAN) and assign it a IP Address , subnet mask and the default gateway. I will use this IP to reach the server. So it is like a management bridge for me.

With kernel 2.6.13.4 linux bridge with traffic management for 4000users and 20.4 MB/s(tx)/22.4 MB/s(rx) data load of CPU is max 50% With kernel 2.6.15.1 the same linux bridge with the same traffic has 100% CPU load and in top I have ksoftirqd proccess. The machine is P4 3.2 GHz with 1GB of ram and 4 NetGear 620 cards The config is: /sbin/modprobe acenic link=0x0100,0x0100,0x0100,0x0100

Hai Marco, > -----Oorspronkelijk bericht----- > Van: Marco Gaiarin [mailto:gaio at sv.lnf.it] > Verzonden: donderdag 11 oktober 2018 14:15 > Aan: L.P.H. van Belle > Onderwerp: Re: [Samba] NFSv4, homes, Kerberos... > > Mandi! L.P.H. van Belle > In chel di` si favelave... > > > If you want to test the module, i have a set ready to test. > > Ahe,

Hi, Sorry for the broad distribution, I''m not sure who best can help me. I''m trying to add a new interface stanza to /etc/network/interfaces. With augtool, I can accomplish this with the following: set /files/etc/network/interfaces/iface[last()+1] bond1 set /files/etc/network/interfaces/iface[last()]/family inet set /files/etc/network/interfaces/iface[last()]/method dhcp set

On 28/01/17 05:21, Kevin Stange wrote: > On 01/27/2017 06:08 AM, Karel Hendrych wrote: >> Have you tried to eliminate all power management features all over? > > I've been trying to find and disable all power management features but > having relatively little luck with that solving the problems. Stabbing > the the dark I've tried different ACPI settings, including

Hi Everyone, I have Samba server 3.5.10 running on RHEL 5.8 platform and it has joined to our AD domain controller. Recently my Windows guys has done some changes to AD Security by stating " CIFS Null Session Vulnerability Fix via GPO - Security Requirement". After this change, my windows clients are not authenticating with domain credentials while accessing the shares, but nothing has

Hi all, I'm trying to setup a cluster of 2 machines with Centos 5.2 to host a postfix+spamassassin+clamav+mailscanner service. Below cluster software versions rgmanager.i386 2.0.38-2.el5_2.1 installed cman.i386 2.0.84-2.el5_2.2 installed Every machine (hp blade server ) has 4 interfaces, bounded in this way: Eth0, eth1

Hi all, Someone played with kickstart bonding with centos 6.4 ? CentOS 6.4, as upstream now support ifcae bonding in kickstart network section. I've an issue with configuring a second bonding iface in kicstart on CentOS 6.4. The first bonding (bond0) works as espected but the second is not configured during installation. I've a 6 nic server (two for "puclic" network, two for

Hello, Where can I find a link (or docs) to *working* network config for xen 4.1.2? My tests (s. below) were not successful. Thank you in advance for any hints. Regards, Mark # --- root@xen411dom0:~# cat /etc/network/interfaces # Used by ifup(8) and ifdown(8). See the interfaces(5) manpage or # /usr/share/doc/ifupdown/examples for more information. auto lo iface lo inet loopback auto bond0