similar to: apcupsd, odd behavior

Ok, so another apc UPS 3000 complained about bad batteries, and I changed them out from the same order that I'd gotten in a couple of months ago. The APC SmartUPS 3000 started connecting and disconnecting the USB connection. I brought down and up the service, no joy. Finally, after googling, I found a *completely* undocumented way to start apcupsd, that a few years ago someone was told to

Well, here's the tale: we got a "replacement kit" for some APC SmartUPS 3000 - rackmount UPSs. The "kit", costing about half of what APC is asking, is just the batteries, and you pull the tray out, open it up, and swap out the batteries. Except, I did this on one... and the replace battery light never went out. Not using apcupsd's apctest, not pushing the button. The

Anyone else around using apcupsd? I seem to be seeing a problem, and I'd like someone to check me on it: I edit /etc/apcupsd/apccontrol to replace the value of SHUTDOWN from /sbin/shutdown to /bin/false (we don't want 3 or 6 servers shutting down over a 2 second or so blip, which it really wants to do). What's happened is that a machine shut down the other day, and looking at it, I

On 2/20/2014 6:55 AM, Charles Lepple wrote: > On Feb 19, 2014, at 12:50 PM, Ted Mittelstaedt wrote: > >> Worse, however, is if there's a power failure right near the end of >> the 2-days-off cycle. That happened to me last week - it was a >> short duration 15 second loss - and the upscode2 driver decided it >> needed to issue a forced shutdown. >> >>

2009/5/3 Thomas Juerges > -----BEGIN PGP SIGNED MESSAGE----- > Hash: SHA1 > > Hi Arnaud, > Hi Thomas, > I just checked the 2.4.1 version of nut and found that you forgot to add > my old UPS model (APC Smart-UPS 900). I guess it is because you were > busy at the time when I sent you the patch. So here it goes again. :) > uh, right sorry. I was pretty sure I applied

I need a little help on this problem, please? I include my /etc/apcupsd/apcupsd.conf file is attached. port 3551 udp/tcp has been added to the (running) firewall. My APC is recognized as: APC Back-UPS 450 FW:844.Kld.D USB FW:Kld This from the hardware browser. PS says: root 2419 0.0 0.0 4196 584 ? Ss Mar23 0:09 /sbin/apcupsd -f /etc/apcupsd/apcupsd.conf Is group 2419 the

Using nut v2.2.2, and the APC serial cable. I have a client who's APC SMART-UPS 1500 (circa 2000) is always reporting LB. The batteries were old so they were replaced two weeks ago with brand new batteries. UPS still reported low batteries... I ran a calibration and a test on the unit (using the nut upscmd utility) During those tests, the battery charge on the unit goes to zero and slowly

Here's an odd one: I installed apcupsd, and it works with most of our UPSs. I'd swear it worked on this one. Then I replaced the Gin-u-wine APC batteries, which were dead, with new ones, non-APC. They're just dumb batteries, no chips or whatever on them. If I hook it up using a serial cable, I can get info. If I hook it up the way I had it, with APC's weird USB cable - and this is

Hej! Hope nut-upsuser is an appropriate place to post additional info about the smartups protocol, please tell me if not. I got an APC Smartups 2200 (5U Rack Mount, European/230V version, 48V batteries) a couple of days ago, was very happy to find the protocol description at http://www.networkupstools.org/protocols/apcsmart.html, and started to play. At the point when everything was working

Hello, This may be a really stupid question, but can a gel type marine battery be used in a UPS? Thanks

Hello, Looking for a apcupsd 3.14.14 rpm. Been getting communication lost errors. I read there was a problem with the 3.14.12 version regarding a usb connection which I'm using, but has been corrected in 3.14.14. I found a Fedora 25 Rawhide src version, but the link must be bad. Was hoping I could rebuild it for Cento 6. Looks like apcupsd no longer producing the rpms. I could build one

Hi, I have an IVR that sounds just fine and dandy over ZAP. However, when I dial in through an 800 number from a provider that I connect to via IAX I get this 'blip' in the sound file. At first I thought it was just packet loss, but it happens at the exact same spot every single time. There are several parts to the IVR menu and several places where this blip happens every single time

We got replacement battery "kits" for some of our APC UPS' (Smart-UPS, rackmount). I put them into one tray (it's for an RBC 43, which takes 8, and weighs a ton), and put it in, and let it charge. Idiot "change battery" led stays on. So I hit the test button, it discharges very rapidly (a good number of servers on this), and the led stays on. For some reason,

On Feb 19, 2014, at 12:50 PM, Ted Mittelstaedt wrote: > Worse, however, is if there's a power failure right near the end > of the 2-days-off cycle. That happened to me last week - it was a > short duration 15 second loss - and the upscode2 driver decided it needed to issue a forced shutdown. > > Very likely this was because upscode2 had decided the batteries > were

Hello. Trouble to communicate with APC SmartUPS via serial port. UPS connected to the com1 port on windows host. Communication witch hyperterm works well. There is a log: YSM ^ASmart-UPS SC1000 n5S0713T63247 m03/29/07 L240.0 B27.10 apcupsd also can communicate with the UPS and works well. running apcsmart -a ups gives the following: com1: device reports different attributes than what were set

> -----Original Message----- > From: CentOS [mailto:centos-bounces at centos.org] On Behalf Of John R > Pierce > Sent: Saturday, December 24, 2016 7:44 PM > To: centos at centos.org > Subject: Re: [CentOS] apcupsd-3.14.14 > > On 12/24/2016 4:33 PM, TE Dukes wrote: > > Looking for a apcupsd 3.14.14 rpm. > > > > Been getting communication lost errors. I

On 7/25/19 4:07 PM, Giles Coochey wrote: > > On 25/07/2019 13:51, hw wrote: >> Hi, >> >> how can DNS reliability, as experienced by clients on the LAN who are >> sending queries, be increased? >> >> Would I have to set up some sort of cluster consisting of several >> servers all providing DNS services which is reachable under a single >> IP

On 2014-01-14 10:12, dstrr wrote: > Hello. > Trouble to communicate with APC SmartUPS via serial port. > UPS connected to the com1 port on windows host. > Communication witch hyperterm works well. > There is a log: > > YSM > ^ASmart-UPS SC1000 > n5S0713T63247 > m03/29/07 > L240.0 > B27.10 > > apcupsd also can communicate with the UPS and works well. >

We have about 4 servers connected to an APC UPS. The UPS only has one UPS connection. So my question is, in a power outage how do i get all my servers to safely shutdown? Do i run a USB hub? Do i write a script on the one machine connected to turn off all the other machines? I'm confused. Jamie

Hello, On Fri, 17 Nov 2017 10:34:53 -0500 Digimer <lists at alteeve.ca> wrote: > On 2017-11-17 10:16 AM, m.roth at 5-cent.us wrote: > > I can't seem to find apcupsd for C 6. Just went to epel's website, and not > > visible. Anyone have a clue? > > > > mark > > I can't speak to epel, but we have copies of it if that helps you; >