similar to: Blazer_usb Permissions problem: Input/output error

Merry Christmas to you all and best wishes! I ran into exactly the same problem as described. OS: FreeBSD 9.0-Rel UPS: Eaton E-Series NV 600H NUT: from Ports, nut-2.6.5_1 driver: blazer_usb I am sure the problem is not permission-related as it occurs even when the driver runs as root. My tested recipe for USB permissions is: 1. run usbconfig to find where the device is connected. In my case:

I'm running Ubuntu 14.04.1 with nut 2.7.1-1ubuntu1, using a Powerwalker/INNO TECH ups. It used to working fine, but lately blazer_usb just executes a few commands and then terminates with a "Got disconnected by another driver" message. Any suggestions? Example output from blazer_usb with loads of debug: # /lib/nut/blazer_usb -DDDDDDDDDDDDDDDDDDDDDD -a nasups Network UPS Tools -

I am using R.2.4.1 on Windows XP 5.1 (SP 2). I have the following line in my R code. Analysis=anova(lm(PM ~ x)) It works the first 60 or so times it is called but then I get the following error message. Error in lm.fit(x, y, offset = offset, singular.ok = singular.ok, ...) : 0 (non-NA) cases In order to examine the input, I preceeded the call with the following. print(PM) print(x) This gave

Hi Team, I've been experimenting with getting the PowerShield Defender 1200VA UPS working and it appears to be supported by the blazer_usb driver, although it did not have the correct permissions within udev to load the driver as the non-root user after an RPM install on Fedora Core 16. [root at localhost ~]# lsusb ... Bus 006 Device 005: ID 0665:5161 Cypress Semiconductor USB to Serial

2009/4/6 Nick Jenkins > Hi, > Hi Nick, > > Just one extra entry for the > http://eu1.networkupstools.org/compat/dev.html list: > > -------------------------- > [UPSONIC-DS800] > driver = megatec_usb > port = auto > desc = "UPSONIC DS-800" > -------------------------- > > This UPS connects with a standard USB cable, and seems to works great

Gabor: note, these HCL reports go to the nut-upsdev list. Begin forwarded message: > From: Gabor Tjong A Hung > Subject: Re: Network UPS Tools - Compatibility List > Date: September 3, 2013 2:18:31 PM EDT > > Sorry, > I just noticed the "If your device isn?t listed" part: > > [HCL] Forza FX-1500LCD supported by blazer_usb > > > [root at freenas] ~#

Syndome Era Series *upsc output* * *battery.charge: 100 battery.runtime: 1000 <-- not reported by UPS (guesstimate) battery.voltage: 13.60 battery.voltage.high: 13.00 battery.voltage.low: 10.40 battery.voltage.nominal: 12.0 device.type: ups driver.flag.novendor: enabled driver.name: blazer_usb driver.parameter.chargetime: 43200 driver.parameter.idleload: 30 driver.parameter.pollinterval: 5

Use the name from ups.conf in front of "@localhost". ?The re?sult is quite different ;) root at artu:~# upsc Elit at artu Init SSL without certificate database Error: Driver not connected > What if you try nutdrv_qx without specifying megatec? (It should > autodetect.) > ?Here is the result: ? root at artu:~# upsdrvctl start Network UPS Tools - UPS driver controller

2008/4/10, David Erosa <david.erosa at gmail.com>: > Public bug reported: > > Binary package hint: nut > > After updating to last nut package (2.2.1-2.1ubuntu6), the megatec_usb > driver seems to be working, except for the charge percentage: > > $ /lib/nut/megatec_usb -DDDDD -a SAI > ... > Checking device (0665/5161) (001/007) > - VendorID: 0665 >

Hello, I have a Salicru UPS in a Debian Wheezy connected with a USB HUB: # lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub ... Bus 001 Device 003: ID 1a40:0201 Terminus Technology Inc. FE 2.1 7-port Hub Bus 001 Device 005: ID 0665:5161 Cypress Semiconductor USB to Serial The problem is that I have some failed messages: # dmesg ... [90941.136274] usb 1-3.7: usbfs:

On Nov 25, 2013, at 4:56 PM, Fabio Cecamore wrote: > Hi all, > after a change of UPS (to Atlantis Host Power 851) I began to use the new driver blazer_usb and compared to old one (blazer used with serial connection) I noted more CPU use and errors in dmesg: > > [...] > [256712.584370] usb 4-5: usbfs: USBDEVFS_CONTROL failed cmd blazer_usb rqt 33 rq 9 len 8 ret -110 "ret

Hello, I am trying to make my UPS system working with NUT but with no success. I got "No supported UPS detected" message. I use the blazer_usb driver since it was proposed to me by the web site. My NUT version is : 2.7.1 (installed from standard RPM), release 2.41 The UPS identification: INFOSEC X4 RM PLUS linux-2qya:~ # /usr/lib/ups/driver/blazer_usb -a infosec Network UPS Tools -

Hi, another UPS piece supported by blazer_usb: ALLSAI model LV 2K upsc output: battery.voltage: 82.08 battery.voltage.nominal: 72.0 beeper.status: enabled device.mfr: device.model: LV 2K device.type: ups driver.name: blazer_usb driver.parameter.pollinterval: 2 driver.parameter.port: auto driver.version: 2.4.3 driver.version.internal: 0.03 input.current.nominal: 18.0 input.frequency: 59.9

On Mar 7, 2014, at 4:12 PM, Josu Lazkano <josu.lazkano at gmail.com> wrote: > Are the messages a problem? Or could I ignore? Since they aren't happening on each poll interval, they are not a big problem. The driver should recognize -110 as a timeout, and retry the query.

2014-03-08 14:26 GMT+01:00 Charles Lepple <clepple at gmail.com>: > On Mar 7, 2014, at 4:12 PM, Josu Lazkano <josu.lazkano at gmail.com> wrote: > >> Are the messages a problem? Or could I ignore? > > Since they aren't happening on each poll interval, they are not a big problem. The driver should recognize -110 as a timeout, and retry the query. Thanks for the

On Apr 3, 2015, at 1:54 PM, Humberto M?ckel <hamberthm at gmail.com> wrote: > I've successfully configured UPSMON to monitor the UPS status, and do the shutdown procedure by calling the SHUTDOWNCMD on a simple bat file I've made. This bat file is as follows: > > cd C:\Program Files (x86)\NUT\bin > blazer_usb -a HAMUPS -k > pause > > So this should send the

Hello I am using Freenas 11.3 (freebsd like) with a GREENCELL usb ups. with nut 2.7.4_13 pre installed But, this ups is not detected as "blazer_usb" on port "auto" neither "ugen0.4"! Network UPS Tools - UPS driver controller 2.7.4 Network UPS Tools - Megatec/Q1 protocol USB driver 0.12 (2.7.4) No supported devices found. detail below. Another info : This

(please use reply-all - this list does not alter reply-to headers) On Sep 10, 2015, at 6:23 AM, Thomas Aichinger <taich at qpl.at> wrote: > > Hi, > > I am using a ALLNET 91500 UPS with blazer_usb driver > > /usr/lib/ups/driver/blazer_usb -a ups91500 -L > Network UPS Tools - Megatec/Q1 protocol USB driver 0.10 (2.7.1) [...] > I set delay.shutdown to 600 sec but UPS

Device web page http://www.samurai-power.com/samurai-smart-1000-lcd UPS is marked as Micropower LCD 1000, but in Slovenia is remarked as Samurai LCD 1000 [ups] driver = blazer_usb port = auto vendorid = 0001 productid = 0000 upsc ups Init SSL without certificate database battery.charge: 100 battery.voltage: 27.40 battery.voltage.high: 26.00 battery.voltage.low: 20.80 battery.voltage.nominal:

Lyonn CTB-1200 root at frambuesa:~# upsc lyonn at localhost battery.voltage: 27.20 battery.voltage.nominal: 24.0 beeper.status: enabled device.type: ups driver.name: blazer_usb driver.parameter.pollinterval: 2 driver.parameter.port: auto driver.version: 2.4.3 driver.version.internal: 0.03 input.current.nominal: 5.0 input.frequency: 49.9 input.frequency.nominal: 50 input.voltage: 213.3