similar to: Physical Network Devices table empty

Hi all, I am running fedora 11 with kernel 2.6.30.9-102.fc11.x86_64 #1 SMP Fri Dec 4 00:18:53 EST 2009 x86_64 x86_64 x86_64 GNU/Linux. I am noticing a partition on my drive is reporting incorrect size with "df", the partition is ext3 size 204GB with about 79GB actual usage, the "df" result show the partition size to be 111GB, 93GB is missing. Please advice on what

Hello All, I have one CentOS 6 KVM virtualization server that I built around a year ago (best I can tell it was in October 2012) at which time I would have been installing 6.3 [0]. That particular install used the Consistent Network Device Naming [1] conventions (PCIe NICs are p1p1, p1p2). I started to build out a new KVM virt server (kickstarting a 6.4 install now as compared to 6.3 back then)

Does anyone have some tips for setting up Broadcom's 802.3AD support or just getting their driver compiled / installed? First off, I noticed redhat claims the broadcom bcm5708 driver has been added to the rhel4 kernel. But I don't see /proc/net/nicinfo which broadcom claims the driver creates when it's successfully initialized. So, I'm trying to build the driver based on the

Hi all, I have a problem when from domU I need to configure a network interface. My system configuration is the next: dom0: xen 3.4.3 with 2.6.18-238.9.1.el5xen kernel, making pci back from a network card. All ok. This is the result from "lspci -v -s 09:00.0" 09:00.0 Ethernet controller: Broadcom Corporation NetXtreme II BCM5708 Gigabit Ethernet (rev 12) Subsystem: Broadcom

Hi, I have a Dell PowerEdge 1950 with two NICs Broadcom NetXtreme II BCM5708 1000Base-T. I installed CentOS 5.1 and Xen 3.0.3 (RPM). One of my virtual machines has Windows 2003 Server. In this virtual machine my NICs appears like "Realtek RTL8139 Family PCI Fast Ethernet NIC". The problem is that when I ping to other machines sometimes the reply time value is very high: C:>

I am trying to install 64 bit R on Linux. But I got the following error - rpm -i R-core-2.10.0-2.fc11.x86_64.rpm warning: R-core-2.10.0-2.fc11.x86_64.rpm: Header V3 DSA signature: NOKEY, key ID 97d3544e error: Failed dependencies: /bin/bash is needed by R-core-2.10.0-2.fc11.x86_64 /bin/sh is needed by R-core-2.10.0-2.fc11.x86_64 /sbin/ldconfig is needed by

Hi all I'm trying to setup second ethernet on Dell 2950 server but there isn't any eth1 device (in the bios are ON) # dmesg |grep eth eth0: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz found at mem f8000000, IRQ 169, node addr 001c23d878bb eth1: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz found at mem f4000000, IRQ 169, node addr 001c23d878bd

Hi, After changing cables,switches,ports, I came to the conclusion that bce is reporting input errors that are not there, or creating them. I checked this with 3 different boxes, all Dell-2950/Broadcom NetXtreme II BCM5708 1000Base-T (B2), and one of them, while running Solaris, reported 0 errors after a week, and freebsd after a few minutes its count was > 100. The errors appear under

I am posting the message below again because it did not go through last night. Help! Steve Timm -- ------------------------------------------------------------------ Steven C. Timm, Ph.D (630) 840-8525 timm@fnal.gov http://home.fnal.gov/~timm/ Fermilab Computing Division, Scientific Computing Facilities, Grid Facilities Department, FermiGrid Services Group, Assistant Group Leader.

I installed 64-bit xen 3.1.0 (from xensource.com tarballs) on three new machines today, using a configuration setup that I''ve used successfully many times before. However, I encountered a new problem. These are Dell Poweredge 1950 servers, by the way. >From lspci 04:00.0 Ethernet controller: Broadcom Corporation NetXtreme II BCM5708 Gigabit Ethernet (rev 12) 08:00.0 Ethernet

Hi, I''ve run into the same issue as: http://lists.xensource.com/archives/html/xen-users/2006-07/msg00599.html In that, running the network bridge script kills networking completely, trying to ping the gateway gives me destination host unreachable. The card is: 09:00.0 Ethernet controller: Broadcom Corporation NetXtreme II BCM5708 Gigabit Ethernet (rev 11) Using the bnx2 module:

host and guest both centos 5.5 network is 192.168.62.40 host is setup as follows [root at cloud2 ~]# ifconfig br0 Link encap:Ethernet HWaddr 00:1A:64:12:10:D9 inet addr:192.168.62.199 Bcast:192.168.63.255 Mask:255.255.254.0 inet6 addr: fe80::21a:64ff:fe12:10d9/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1705488

Hello list, I have two differents installation Xen Hypervisor on two identical physical server, on the same switch : The problem is on my new server (Xen 4.0.1 with pvops kernel 2.6.32.24), I have bad performance on bandwidth I have test with a files copy and "iperf". Result iperf average: Transfert Bandwidth XEN-A -> Windows

http://bugs.freedesktop.org/show_bug.cgi?id=24328 Summary: swfdec crashing in both firefox and epiphany Product: swfdec Version: unspecified Platform: Other OS/Version: All Status: NEW Severity: normal Priority: medium Component: plugin AssignedTo: swfdec at lists.freedesktop.org

Hi, I have been playing this weekend with bonding on PCI netcards and found that all of netcards I have, but old 3com, do not support MII. So bonding is not going to happen with them. Do you have some pci netcards supporting MII successfully running on bonging? Thanks, David Hrb??

> -----Original Message----- > From: Gordon Messmer > Sent: Monday, August 31, 2015 12:15 PM > > On 08/31/2015 03:51 AM, Jason Pyeron wrote: > > I feel like this is an issue of libvirt starting before networking, > > but I am a fish out of water with systemd. > > Are you using the "network" or "NetworkManager" service to > configure your

Hello, I''ve this strange problem. When Xen kernel start and it try to start eth devices, network doesn''t work. It seems to be a problem with NICs firmware. Anyone had this problem? Do you know where I can download firmware upgrade? (on DELL''s site I''ve just searched...) Thanks, Carlo No virus found in this outgoing message. Checked by AVG Free Edition.

I am having the same problem. But, I cannot access to the following link for solution http://wiki.ncsa.uiuc.edu/wiki/Dell_PE1950_NIC_Firmware_Workaround Can someone send me the content of this link? Thanks. Pete, This may be relevant: http://wiki.ncsa.uiuc.edu/wiki/Dell_PE1950_NIC_Firmware_Workaround - Mike At 8/18/2006 09:40 AM Friday, Peter McEvoy wrote: Hi, I''ve run

Hi, I don't have ifcfg-eth1 in my /etc/sysconfig/network-scripts. But when I do ifconfig eth1 I can see output as below. If I do ifconfig eth12 , I don't see anything which i am assume is normal. eth1 Link encap:Ethernet HWaddr 00:24:E8:44:DB:CC BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0

Hi, Boris! i have installed and run virt-manager successfully. After i boot into my xen paravirt kernel I got, [root@Server1-FC11 init.d]# xm info host                   : Server1-FC11 release                : 2.6.30-rc6-tip version                : #1 SMP Thu Oct 22 12:48:59 PKST 2009 machine                : x86_64 nr_cpus                : 8 nr_nodes               : 1 cores_per_socket       :