Displaying 15 results from an estimated 15 matches similar to: "No progress tones on transferred call"
2014 Mar 02
1
cisco spa phones and sal
Hi
?? I have been trying for several days get 3 Cisco spa508g phones
(firmware 7.5.5) to work with asterisk 11.6 cert1 and sla. I can get
the phones to all ring when an incoming call arrives, and I see the
slatrunk working. However the blf function does not work. If one
extension picks up the call the others do not show the trunk in use.?
And as you might expect the hold and outbound dialing does
2006 May 26
0
SIP call problem
Hello,
I have problem to make SIP calls, i have asterisk +
PC InterP4 + Digium TDM400P
here is the content of the sip.conf:
[SIP_PROVIDER]
type=peer
fromuser=testcomclient
username=testcomclient
secret=testr
host=IP_SIP_PROVIDER
;dtmfmode=rfc2833
context=interne
canreinvite=no
;allerid=Beer
disallow=all
allow=ulaw
allow=gsm
allow=g723.1 ; Asterisk only
2013 Apr 26
0
glibc detected crash
Hi
I have asterisk 1.8.18 with freepbx 2.10.1.9. I get an asterisk crash occasionally with the followingerror. It always seems to happen while paging.
16 spa508g phones
1 snom pa1 paging amp
Kelly
== Extension Changed 1101[ext-paging] new state Idle for Notify User 101
pbx*CLI> *** glibc detected *** /usr/sbin/asterisk: malloc(): smallbin
2006 Apr 14
0
[Bug 471] New: UDP stream DNAT problem
https://bugzilla.netfilter.org/bugzilla/show_bug.cgi?id=471
Summary: UDP stream DNAT problem
Product: netfilter/iptables
Version: linux-2.6.x
Platform: All
OS/Version: All
Status: NEW
Severity: normal
Priority: P2
Component: NAT
AssignedTo: laforge@netfilter.org
ReportedBy:
2005 Mar 07
0
SIP URI
Hello,
I try to append a URI to the SIP dial syntax, however the URI were not shown
in the sip debug message. I have read one of
the post in the list which actualy show the URI string in the debug message
(at the To: field). Is there any setting I need to set or turn on during
compilation of asterisk? I have the head version of asterisk and my
extension.conf setting is proveded below:
exten
2013 Nov 27
2
Permissions problems
Hi,
I have dovecot 2.0.20 running (its an old version, I know, it came from the
stable archive at OpenCSW) with Solaris SMF integration working fine. It
enables and disables okay.
However, I cantt connect to it, it is allowing the connection, but spewing on
permissions:
Nov 24 17:34:20 proliant-1 dovecot: [ID 583609 mail.info] master: Dovecot
v2.0.20 starting up
Nov 24 17:34:27 proliant-1
2014 Jun 03
2
director with multiple instances
I'm experiencing some problems similar to those described in
http://dovecot.org/list/dovecot/2012-July/137250.html
except with 2.0.9.
Adding http://dovecot.org/list/dovecot/2012-July/084906.html
to the main config didn't seem to help, nor did setting the list of
director and backend servers to just the system itself.
I get a banner connecting to port 143:
[root at retr01 log]# telnet
2005 Mar 08
1
samba WINS problem on 2 networked LANS using a VPN connection
Hello Samba experts,
Please read all email because i'm desperate!!!!!
I have problem on joining to LAN-s using Samba. Finally i got a solution to
"see" booth workgroups on "Entire Network", but i'm having problem with
stations located in LAN2. From any station located in LAN1, I can see LAN2
workgroup and the browse list with stations located in LAN2, but when
2011 Jan 26
3
missing vif.0 port after install xen4+centos5
Hi !
I have install the xen4+centos5 on my server following the post of
the kernel version is 2.6.32.27 which is download from
git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen.git
But after I reboot the server ,and run the "ifconfig", whose output likes
the following
[root@localhost scripts]# ifconfig
eth0 Link encap:Ethernet HWaddr 00:15:C5:EB:96:C3
2009 Jan 12
11
dedicated vnic IP zone not recieving unicast traffic
Hi Folks,
I have a snv_105 sxce host that I just can''t get to work as expected with crossbow + zones.
My test host persephone, is a virtual machine running under VMware ESXi 3.5, with 2 virtual network cards (e1000), all on the same flat network/subnet.
It started life just 2 days ago with a clean install of snv_95, and I LUed to 105 yesterday.
To rule out any sharing issue, the first
2014 Jan 10
1
Switch mode three-node routing problem
Dear tinc community,
I am using tinc in switch mode. I have three nodes. Two nodes reside on
routers, vpn-eth is bridged with internal lan, each router has several
machines connected to it's internal lan. Third node is the roadwarrior -
"endpoint" linux PC.
When the roadwarrior is off - everything works perfectly, machines on both
sides can communicate without a problem in any
2015 Jan 21
0
asterisk-users Digest, Vol 126, Issue 18 mtr
You could use MTR command.
Its a trace route improved.
Marlon Araujo
> On Jan 20, 2015, at 08:59, asterisk-users-request at lists.digium.com wrote:
>
> Send asterisk-users mailing list submissions to
> asterisk-users at lists.digium.com
>
> To subscribe or unsubscribe via the World Wide Web, visit
> http://lists.digium.com/mailman/listinfo/asterisk-users
> or,
2015 Jan 19
2
SEMI-OFFTOPIC openvox
Hi list, I write on the list looking for help, buy a openvox gw gsm
for four channels and I'm a little disappointed with the support
openvox, for some reason , The call doesn?t get trough
support tells me it was my asterisk server, but does not really work
me and my internal calls are working perfectly, I tested with another
sangoma FXO gateway and works perfectly.
the problem is that
2002 Jun 27
5
[Bug 306] ssh on Tru64 returns " Name does not resolv to supplied parameters"
http://bugzilla.mindrot.org/show_bug.cgi?id=306
------- Additional Comments From cmadams at hiwaay.net 2002-06-28 00:31 -------
I'm not seeing this on Tru64 4.0G or 5.1A with OpenSSH 3.4p1. What does
"rsh [server]" say? Are you using IPv6?
------- You are receiving this mail because: -------
You are the assignee for the bug, or are watching the assignee.
2004 Jan 23
3
Problem installing Asterisk with Mandrake 9.1
Hi All,
I am trying to get Asterisk up and running on my new Mandrake 9.1 install.
I've installed Linux in the "standard" mandrake security mode, and "su" to do
my attempts at install.
I managed to obtain the source from CVS, and have been able to compile Zaptel.
I then ran insmod zaptel, and also make config.
I think I have compiled and loaded Zaptel successfully as