similar to: AHC Panic

After compiling the kernel 4.9RC1 dmesg gives the following error lpt0: Interrupt-driven port ppi0: <Parallel I/O> on ppbus0 ed1: <Realtek Plug & Play Ethernet Card> at port 0x220-0x23f irq 5 on isa0 ed1: address 52:54:40:28:83:9a, type NE2000 (16 bit) ad0: 4112MB <WDC AC24300L> [8912/15/63] at ata0-master WDMA2 Mounting root from ufs:/dev/ad0s1a module_register: module

[ Asked on -questions on Friday; re-asking now on -stable without cross-post] I recently upgraded a 4.11-REL machine to 6.0-REL and have run into some snags. While the installation from CD went fine, after configuring and enabling my ed0 NIC, bad things start to happen. FWIW, this machine is an ancient (hardware circa 1991, BIOS circa 1994) dual-Pentium 133 MHz machine, with EISA/PCI and

Hi I have a quad processor Compaq Proliant 5500. The output from dmesg seems strange (I have also sent a copy to freebsd-smp to ask about smp issues) and there are also some performance issues which I suspect are smp related. Could anyone who fels so inclined please take a look at the output and let me have any comments. Thanks _______________________________ Copyright (c) 1992-2002 The

I put this to the smp list and to stable but have had no takers from wither. nThere are both smp and other system issues and I am just wondering if anyoe would be willing to take a look at this output from dmesg and let me have some advice Thanks david ----- Original Message ----- From: "vizion communication" <vizion@ixpres.com> To: <freebsd-smp@freebsd.org> Sent:

Hi, After kernel panic I couldn't get gdb work properly. msi$ uname -sr FreeBSD 4.7-RELEASE msi$ gdb -k /usr/src/sys/compile/MSINW/kernel.debug vmcore.0 GNU gdb 4.18 (FreeBSD) Copyright 1998 Free Software Foundation, Inc. GDB is free software, covered by the GNU General Public License, and you are welcome to change it and/or distribute copies of it under certain conditions. Type "show

Graham Bentley wrote: > Recently swapped out my Sony for a HP DAT and > got this first time in dmesg > > (sa0:ahc0:0:6:0): PREVENT ALLOW MEDIUM REMOVAL. CDB: 1e 0 0 0 0 0 > (sa0:ahc0:0:6:0): CAM Status: SCSI Status Error > (sa0:ahc0:0:6:0): SCSI Status: Check Condition > (sa0:ahc0:0:6:0): UNIT ATTENTION asc:28,0 > (sa0:ahc0:0:6:0): Not ready to ready change, medium may

Hi, All. I'm trying to use HP Suresore 24e on FreeBSD 4.8-STABLE (Mon May 12 09:32:15 YEKST 2003). The system is installed on Asus P2b-DS motherboard with Adaptec aic7890 onboard scsi-controller. I have 2 SCSI-3 HDDs attached to it: da0: <IBM DDYS-T18350N S96H> Fixed Direct Access SCSI-3 device da1: <IBM DDYS-T09170N S80D> Fixed Direct Access SCSI-3 device and I'trying to

Hi all, is there a known issue with health monitoring on supermicro SuperServer 6010H? (Im primarily interested in temeperature monitoring) I have tried both mbmon and lmmon with the following results: stats# mbmon -d SMBus[ServerWorks(ServerSet Chipset)] found, but No HWM available on it!! No Hardware Monitor found!! InitMBInfo: Unknown error: 0 stats# lmmon IOCTL: Operation not supported by

Hi all, I have some problems with my gvinum setup after the system panic'ed. Afterwards the system fails finding the plexes to the subdisks (or at least that is what I can understand after having searched the gvinum source code for the error string in the DMESG log..) The machine is an IBM Netfinity 5000 and the internal HW self tests does not find any errors in the hw. Luckily my root is

I am getting these messages every 30 seconds or so. I searched around and found a few other post about this problem with other devices, but no answers to the problem. I didn't notice any of these message until I upgrade to 4.8-RELEASE the other day. This is a dual processor machine. It happens on all my machines that have em devices, which all happen to be dual processor machines. I

Hello, My server is experiencing occasional kernel panics when under moderate load. I'm attaching a crash dump and the dmesg output. I'm not sure how to read the kernel backtrace but it looks like the Intel NIC (em0) caused the problem. Occasionally, I used to get a "em0: watchdog timeout -- resetting" error message, but I never had a kernel panic. The problem started last

Hi, Can someone please help me with this? I have just upgraded from 4.7 to 4.8-STABLE and this is what I am getting when I try a tape backup. Please CC as I am not in the list. It was working well before the upgrade (dump -0ua -f - / | gzip -c -9 | dd of=/dev/nsa0). Thank you, Lefteris Tsintjelis Jul 3 22:55:18 ene /kernel:

Well, 4 days after previous upgrade i cvs'ed RELENG_4 from local cvs tree (updated hourly), made buildworld buildkernel installkernel, rebooted into single user, made installworld and mergemaster. Mergemaster updated newsyslog.conf, syslogd.conf, ok, rebooted... Wow... All scripts from /usr/local/etc/rc.d refused to load. And the system is in "Amnesiac" mode Attempt to run

FreeBSD 4.1.1-RELEASE #1: Tue Oct 10 18:09:51 CDT 2000 root@test-drive.tamu.edu:/usr/src/sys/compile/TEST-DRIVE Timecounter "i8254" frequency 1193182 Hz CPU: Pentium III/Pentium III Xeon/Celeron (501.14-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0x683 Stepping = 3 Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CM

I've search the archives & found several requests for help with configuring Samba for 2 ethernet interfaces, but can't seem to find any answers posted. So, I'll try asking! I've got a FreeBSD server running samba (version 1.9 something I think, definitely not version 2). It has 2 ethernet interfaces which are configured correctly for tcp/ip - I can telnet the server from

One of our FreeBSD boxes has a SCSI controller and disk, which showed problems earlier this week. There was a lot of of chatter from the SCSI driver in /var/log/messages and to the console. However, the console is unattended and we only discovered the problem subsequently because /var/log/console.log didn't show any of the chatter. console.log is otherwise working, and very helpful (e.g. it

Hello lists, I,ve compaq ML350 with 2 Xeon 2.4 GHZ and FreeBSD 5.0 RELEASE installed and working very fine about 4 mounts. The machine running GENERIC kernel samba and firebird database server with no problems until at begining of this week, in morning machine freezes with no responce iven in conconsole, no responce from network (pinging) no responce on console (key pressing) the only way to get

currently i'm trying to setup diskless client, which netboots 6.1-PRERELEASE kernel with help of etherboot. i've built custom kernel with `sudo make -j4 buildkernel KERNCONF=DISKLESS CPUTYPE=pentium-mmx -DNO_MODULES' and attached config. kernell loads off tftp server fine, detecting devices, but traps, when trying to mount root fs from nfs server. i've managed to get copy of

With FreeBSD 4.8-20030731-STABLE #0, dmesg messages indicate: module_register: module miibus/ukphy already exists! linker_file_sysinit "miibus.ko" failed to register! 17 module_register: module pccard/ed already exists! linker_file_sysinit "if_ed.ko" failed to register! 17 This doesn't look dangerous but the rl0 ethernet card just stopped recieving packets suddenly and

hi! I'm experiencing troubles with $(subj). What I actually had before is an NT box. Now it's been replaced by FreeBSD box with 2 network interfaces: ed0 has real ip address & ed1 has local ip 10.0.0.1. NT box is now assigned ip 10.0.0.2 & is connected to FreeBSD's ed1. After this change NT box doesn't see its workgroup. Workgroup has WINS server (functioning on