similar to: How does UDMA mode get set?

i cannot read or write any disk inserted in my acd0 <PIONEER DVD-RW DVR-111D/1.29> when this device in udma mode. kernel endlessly repeat that acd0: setting up DMA failed and I can access my data on dvd or cd only if I set atacontrol mode acd0 pio4 Does anybody have such a problem too? is there any ways to bring this device into udma mode again? dmesg: ... atapci1: <ATI IXP600

I'm trying to get stable booted on a little ITX board off of a CF card, but it hangs as it's trying to run init. Here's what the boot looks like. SMAP type=01 base=0000000000000000 len=000000000009fc00 SMAP type=01 base=000000000009fc00 len=0000000000000400 SMAP type=02 base=00000000000f0000 len=0000000000010000 SMAP type=02 base=00000000ffff0000 len=0000000000010000 SMAP type=01

Hi there, sorry for rather long mail. Two verbose dmesgs and `pciconf -vl` outputs attached. trying to set up new machine based on ASUS P4BGL-MX motherboard, I'd encountered hangs after detecting pcib1 (ICH2). MB has rl 8100 ethernet chip onboard. This is for 4.8-R; however, machine hangs in very similar way also with 4.4-R and 5.1-R. Matrix of hangs: Onboard Ether External Ether Result

Hello, I've got a (P)ATA disk in a special frame. The disk itself supports UDMA-100 (and has an 80-ribbon cable), but the frame isn't compatible with that. By default, FreeBSD negotiates UDMA-100, and the console starts to fill with ICRC errors. In the past, I used a patch to ata-all.c that enabled the following entry in loader.conf to force the disk to UDMA-33, so it worked fine:

Hi, I am using an ASUS CUV4X-E mother board with a scsi adapter Adaptec AIC-7881U, with one QUANTUM ATLAS_V_18_WLS and MAXTOR 4K040H2, ATA DISK drive connected with a VIA vt82c686a (rev 22) IDE UDMA66 controller. The instalation from original kernel 2.4.7 was ok, but when I upgrade to kernel 2.4.9-31, almost every day I got an error in many process, including apacha, qmail and many

Hi. There's a rescue cd at ftp://ftp.pld.org.pl/people/areq/RescueCD/ that uses isolinux that don't work in my configuration. All I get is: --8<-- ISOLINUX 1.75 2002-06-14 isolinux: loading spec packet failed, trying to wing it... isolinux: extremly broken bios detected, last ditch attempt with drive=9F isolinux: disk error 80, ax=432E, drive 9F --8<-- My configuration is: VP_IDE:

Hi After my previous email about the SETFEATURES SET TRANSFER MODE timeout on (msgid 441AA807.5090100@wfeet.za.net , 17 March 14:18 GMT + 2 on freebsd-stable), I installed FreeBSD 6.1 BETA 4 and upgraded to a 6-STABLE kernel, running the box in 'safe' mode to do so. I now, however, get a slightly different error message: ad4: WARNING - SETFEATURES SET TRANSFER MODE taskqueue timeout

Hi I have a newly installed FreeBSD 6.0 release machine on which I am getting the following error on the console: "ad4: req=0xc23bc258 SETFEATURES SET TRANSFER MODE semaphore timeout !! DANGER Will Robinson !!" This is generally associated with heightened disk activity, but it happens inevitably after a while (minutes or hours) if the machine is running. The atacontrol list shows:

Hello, I have the following hardware configuration. Tyan 2466N motherboard, 1.03 BIOS, 2 Athlon-MP 1800+ CPUs, 512MB registered ECC DRAM, Onboard 3Com NIC (xl type) Radeon 8500 AGP video card Adaptec 3210S SCSI RAID controller Comtrol RocketPort 8 port PCI serial card I have started to experience some odd system lockups in the past couple months, and it seems to be getting worse. I particular,

I had a sparc64 (Netra X1) running a stable/9 from late March 2013. Actually, the kernel may've been a bit newer than that as I was working with folks to diagnose and repair some Netra-X1 specific issues. But, ZFS worked fine. I have two pools, zroot as a RAID1 (using equally sized partitions at the front of two large disks), and a zdata that is a large pool of the remaining space of both

I sent a note about this a couple of weeks ago, but have not heard anything. I'm really getting a bit desperate. I have a system that I am trying to upgrade from 8.2 to 9.0. I have built it and installed the kernel, but it fails to boot. The boot freezes after probing for my hard drives during the probe of the CDROM. It just sits there, seemingly forever, though I have never waited longer

Hi there. OS version: FreeBSD 4.7-Stable FreeBSD #3 I just added a disk to my box and after playing with fdisk and disklabel with this configuration: fdisk: **************************************************************** g c16383 h16 s63 p 1 165 0 39102336 **************************************************************** disklabel

Hello! Has anyone gotten 4.9R to recognize the "ServerWorks CSB6" ATA controller on a Dell 600SC? How about installing 5.2R on a 600SC? 5.2R recognizes the said controller, but it corrupts data. -- eof

Hi there, from time to time my PC panics when I insert an empty DVD or CD-R. The kernel locks up instantly after the DVD writer's tray is closed. It seems burning the first DVD isn't critical but inserting the second one seems susceptible. I use k3b as software, which polls the hardware while the tray is open, maybe it's something with hald. Don't know, just use this. I

My wife's box has a very intermittent problem, when booting from the Maxtor IDE hard drive. This has been going on for about 2 1/2 years.... The box is a Compaq EVO D300v for the Enterprise. When it boots, there is a SMART advisory from the BIOS that says failure is immenient. Occasionally, it will not boot, because the BIOS does not see the hard drive. I replaced the EIDE cable, but the

All: I cvsup'ed earlier this evening and am still able to reproduce this panic at will. Command line, panic backtrace, dmesg, ldd output, and mplayer version follow. If more information is needed, just let me know. % mplayer foo.mov [a quicktime file] [plays for awhile, and then panics] # gdb -k -s /usr/obj/usr/src/sys/LICHEN/kernel.debug -e /var/crash/kernel.2 -c /var/crash/vmcore.2

Okay, I've been chasing performance for a while now. I have no idea if I should be trying to get better performance or if I'm getting all I can out of my hardware. Here is the information: /sbin/hdparm -I /dev/hdd /dev/hdd: ATA device, with non-removable media Model Number: ST328040A Serial Number: 7BY034XB Firmware Revision: 3.07 Standards:

Hello, Before a couple of days ago I started /usr/local/sbin/cupsd manualy from console. When I press CTRL+C to interrupt a program, the system change runlevel and going to reboot. This was on FreeBSD V5.3, today I installed fresh new 5.4 but the problem is the same. cups-base-1.1.23.0_3 -- Todor Dragnev <todor.dragnev@gmail.com>

Hey all, I''m not sure if this is a ZFS bug or a hardware issue I''m having - any pointers would be great! Following contents include: - high-level info about my system - my first thought to debugging this - stack trace - format output - zpool status output - dmesg output High-Level Info About My System --------------------------------------------- - fresh

https://bugs.freedesktop.org/show_bug.cgi?id=63481 Priority: medium Bug ID: 63481 Assignee: nouveau at lists.freedesktop.org Summary: Nouveau driver - No monitor signal on chipset NV1A (family NV10) since bisected bad commit ebb945a94bba2ce8dff7b0942ff2b3f2a52a0a69 in kernel 3.7.9 QA