similar to: KINGSTON SOHO Hub

Hello, A client of mine has this ancient software called VideoPrinter (working on Win98) and an ancient hardware that connects to the PC through both LAN cable and serial (COM) cable. I decided to give this software a try with wine 0.9.60 running on Slackware 12, kernel 2.6.23.4. The software installs without problems and after adding the appropriate registry keys the COM is recognized. But the

I have recently upgraded my firmware from v6.3 to v7.4. Now when the phone is booted or rebooted, the initial screen "Initializing Vlan" takes forever to initialize before it initializes IP. Any ideas/Thoughts? (Trying not to Revert back to v6.3). -C -------------- next part -------------- An HTML attachment was scrubbed... URL:

I am using RHEL4 with kernel 2.6.9. I can load this on my hardware by passing the following kernel parameter: memmap=496M at 16M, and it loads up and runs OK. If I do not use this parameter, I get a kernel panic. When I try to load the same software onto the same hardware using PXE, I add the same parameter on the server's tftpboot/pxelinux/pxelinux.cfg/default file: append

Just a reminder, the Cambridge LLVM Social is this week on the Kingston Arms. http://www.kingston-arms.co.uk/ cheers, --renato -------------- next part -------------- An HTML attachment was scrubbed... URL: <http://lists.llvm.org/pipermail/llvm-dev/attachments/20130218/bf47bf37/attachment.html>

Hi folks, As the temperature begins to warm up, I expect more people to show up in February. Since the 13th is half-term, the proposed date is 20th Feb. We're changing the pub again: http://www.kingston-arms.co.uk/ It's very close to The Blue, even closer to the station, and also a very good pub. Please let me know if you're coming, so I can arrange a big enough table. cheers,

All Probably teaching you all to suck eggs but. My provider is Kingston Comms ( UK ) and I have had a bit of a struggle to get the * system setup on their cct's. Just thought I would let you all know what I had to do. Firstly order ISDN 110 they will try to provide ISDN 85 as standard. Make sure these settings are correctly defined. [zapata.conf] signalling=pri_cpe switchtype=euroisdn

All I have just been told by GS support .... BTW, the attendant transfer is OK now and under QA test, will be released in next 2 or 3 weeks. Please keep tuned. Sounds like good news. Also if anyone wants the new firmware it's at http://voip.orbital.net/gs11 As for Kingston Comm's if anyone in the UK is connecting ( E1 ) with them you could do worse than seek the advice of Darren

> I've recently got a new flash drive (Kingston DT Micro 3.1 64GB) and > found my existing SYSLINUX 6.02 fails to load on it, it just shows the > version info and hangs forever. > > I've tried 6.03 as well as the latest git revision (currently > 5483860), they both give me "Failed to load ldlinux.c32" > The same builds and config work on my Kingston DT 101

I wish to change the ownership and access permissions of files and directories contained on this device. The device is immediately recognized and mounted when plugged in and I can create and move files on it. However, I cannot change either the permissions or the owner of any file or directory on this device, nor of the device mount itself, whether logged in as the owner or as root. Why is this

Any recommendations on an economical layer 3 switch? Preferably something that you have hands on experience with connecting to IP phones with attached PCs? Specifically I need the ability to set the VLAN in the phone to tag voice packets and to set a native VLAN on a per port basis on the switch to put the untagged packets from the attached PC into a separate VLAN. POE is not a requirement

http://homie.homelinux.net/wordpress/?p=11 _______________________________________________ Xen-users mailing list Xen-users@lists.xensource.com http://lists.xensource.com/xen-users

I work with a SoHo based design firm and we are looking to hire another rails programmer for 2-3 days per week. We work with large non-profits and most of the work involves content management systems, event registrations systems, contact management etc... (nothing out of this world). If you are in the New York Metro area, can make it to a SoHo office a 2-3 days a week and know your way around

Hi, I'm looking to backup a small network (Hughes DW7000 satellite modem, small consumer grade Internet Broadband router+wireless, Soekris NET4801 single board computer + 4 port lan card, Cisco 2900 switch) and want a small form factor (This is sitting on a small shelf) and light. The main thing I'm running into is that it *HAS* to be serial. (The Soekris only has 1 USB port and I

After scouring the list archive and not finding the answer I decided to post to the list. I'm sure the answer is glaringly obvious but please bear with me. Using Asterisk, I'm tasked with setting up a SOHO with 5 analogue (FXS?) lines and a number of soft-phones for internal extensions. I'm confused by the telephony hardware needed for this exercise - 1) I need the equivalent of two

Does any one know of an accounting app that will run properly under wine, must be for USA, must have inventory and payroll. Must not require accounting degree to operate. Something that will actually work...............

Hello, I wanted to send an email to the administrator of the web to update an information, I do not know if this mailing list is appropriate. I just wanted to say that I have a UPS SALICRU SOHO + 1600VA and after several days trying to configure it I found out the problem. This UPS has usb 1.0 HID, so it does not work with the driver usb blazer if you have to use the driver usbhid-ups. I think

Hi What is the best way to setup a Samba server as a file server in a small SOHO. I have to connect 2 windows XP machine and one XP home notebook to a small SOHO network. I want to use a Samba server. I have got it working except I cannot get XP to write to the Samba server. I can read but not write. From the Samba server I can read and write the XP machines. I have set the Samba server up

Hi all, My name is Sergio Penen and I'd like to contribute to the project by developing a new driver for TS SHARA SOHO II usb ups. I'm almost done decoding the protocol and already have some basic functionality working with NUT. However I've some doubts on how to integrate this driver with NUT and I wonder if you could give me some guidance in that sense. To be more specific: In order

I hope the subject isn't too buzzword compliant :) I'm just curious: What have people done with Asterisk? I'm particularly interested in DIY projects and things that can be done on a small/home office (or even hobbiest's) budget. If you have clever hacks or creative functionality you've implemented, I'd love to hear what a few people have come up with. Thanks! -Brian

I've recently got a new flash drive (Kingston DT Micro 3.1 64GB) and found my existing SYSLINUX 6.02 fails to load on it, it just shows the version info and hangs forever. I've tried 6.03 as well as the latest git revision (currently 5483860), they both give me "Failed to load ldlinux.c32" The same builds and config work on my Kingston DT 101 G3 32GB. Both are formatted as NTFS