similar to: libpri / ISDN feature ECT (explicit call transfer)

I'd be grateful if anyone here could comment knowledgeably on an idea that I have had, as to whether it should be possible or not. Consider two Asterisk boxes, each with one or more E1s on EuroISDN. Each box has a different telephone number that hunts across all its E1 channels. In addition there is another number that hunts across all the channels on all the boxes. A call comes in to one of

Hi I installed Asterisk 1.8.7 with CD ISO(Elastix 2.2) I want to use DAHDISendCallreroutingFacility Application on a PRI link(LIBPRI Already installed). according to https://wiki.asterisk.org/wiki/display/AST/New+in+1.8 Asterisk 1.8 include this application but I cannot see it with "core show applications" Do I need to install mISDN or other modules for using that ? Regards M.Shirazi

Hi, I have the following setup: Ubuntu 12.04.02 LTS (64 bit) Asterisk 11.2.1 Sangoma 4-Port-Card (A104d) with firmware 43 (german e1-ports connected) WANPIPE Release: 3.5.28 DAHDI Version: 2.6.1 Echo Canceller: HWEC libpri version: 1.4.12 I call via sip into the dialplan. Then I do a "Dial(DAHDI/g1/voicenumber,r)". The call is bridged and everything is fine. "dahdi show

hello:I used libpri 1.4.12 version with asterisk 1.8.7, after the pcap files, i found thatin wireshark setup message, the number type always changed from subscriber to national number.i have set pridialplan= local and prilocaldialplan=local in chan_dahdi.conf already. because that, the systemsometimes can not make outgoing calls. anyone can clarify that? Best regards, James.zhu Doing

Hi, I am using: Asterisk 11.2.0 libpri 1.4.12 Dahdi: 2.6.1 Sangoma E1-Card with Wanpipe-Drivers 3.5.28 I call my asterisk box via SIP and connect the call to an AGI-Script. Within the script I do EXEC SetCallerPres prohib or EXEC SetCallerPres prohib_not_screened But I get the following error: ast*CLI> == Using SIP RTP CoS mark 5 -- Executing [100 at sip:1]

hi, i have the problem that i'm not able to set and receive the Service Indication (SIN) from our E1-PRI and from our ericsson BP250. The problem is, that the Bearer Capability (BC) together with the High Level Compatibility (HLC) and Low Level Compatibility (LLC) forms the Service Indicator (SIN). The SIN is used to determine if the call is voice, fax or data. It's essential to set

Hi, I'm facing a strange problem. My setup is: Alice cellphone <--GSM--><--ISDN--> Asterisk <-- ISDN --><--GSM--> Bob cellphone When Alice calls Asterisk which forwards the incoming call to Bob, sometimes Bob sees Alice's number, sometimes he sees a default CallerID (which happens to match the dialed number and the ANI). For various reasons, Bob really needs to

Hi, After an upgrade, I discovered yesterday strange things I would like to share here. Basically, I'me comparing platforms: The first one is a 2.6.26 (Debian Lenny) platform, with Asterisk 1.6.1.18, Libpri 1.4.10.2, Dahdi revision 8853 (must be between 2.3 and 2.5, I think). The second one is a 2.6.32 (Debian Squeeze) platform, with Asterisk 10.5.1, Libpri 1.4.12, Dahdi 2.6.1. Both are

Hi, Is libpri rpm version 1.4.12 for CentOS 5.6 made available ? [root@ ~]# rpm -qa | grep libpri libpri-1.4.11.5-1_centos5 [root@ ~]# cat /etc/redhat-release CentOS release 5.6 (Final) [root@ ~]# [root@ ~]# yum list updates | grep libpri [root@ ~]# Please suggest/guide further. Regards, Kaushal

Hello, Limiting the call duration with the L-option of the Dial()-command is working fine, however the announcement is not played. Dialplan : exten => _367,n,Set(LIMIT_PLAYAUDIO_CALLER=yes) exten => _367,n,Dial(SIP/test6,,L(11000,5000,5000)) The call lasts for 11 seconds, but 5 minutes before time runs out an announcement should come. I hear no announcement, not on caller-side nor on

Hi, I would appreciate some advice on the following: how does one use a single BRI port HFC chipset based ISDN cards with the latest DAHDI, libpri and Asterisk 1.8? For Asterisk 1.4 I would first install mISDN & mISDNuser and then build Asterisk 1.4. Now I noticed that Digium's HFC chipset based B410P is supported by the latest DAHDI & libpri but reading the source of the

I just updated libpri 1.4 on my system to the latest from that branch and my QSIG connection to an NEC SV8300 stopped working. The trace showing the problem is below: q931.c:5640 q931_connect: Call 7168 enters state 10 (Active). Hold state: Idle > DL-DATA request > Protocol Discriminator: Q.931 (8) len=21 > TEI=0 Call Ref: len= 2 (reference 7168/0x1C00) (Sent to originator) >

Hi All; I have an E1 card with two ports for ISDN PRI. Do I need to install DAHDI in addition to LIBPRI? For placing outside calls (outgoing) via the PRI, then in the extension.exe file, I will use the Dial function? But how can I determine that I need to use the PRI channels and not the analoge channels? Last point: how can I know that asterisk is containing libpri? In other words, how can I

hi folks. recently some of our customers complained about bad voice quality on the phone system. i looked at the logs and found a lot of these: [2012-11-03 08:26:38] NOTICE[11305] chan_dahdi.c: PRI got event: HDLC Abort (6) on D-channel of span 1 [2012-11-03 08:26:45] NOTICE[11305] chan_dahdi.c: PRI got event: HDLC Abort (6) on D-channel of span 1 [2012-11-03 08:26:54] NOTICE[11305]

Hey Guys Im trying to find out how to transfer a call with ECT (explicit call transfer) ? Im currently transferring a call as following: exten=>2,1,Dial(capi/720****:078888****,18) exten => 2,2,Goto(2-${DIALSTATUS},1) exten => 2-NOANSWER,1,Dial(capi/720****:07979****) exten => 2-CHANUNAVAIL,1,Goto(1,1) exten => 2-BUSY,1,Dial(capi/720****:07979****) If I wanna transfer a call with

After working fine for a week or so my new Quad E1 asterisk 1.8 system has started rejecting outbound calls from the Nortel BMC 450 it is connected to. The cli fills up with these: sig_pri.c: Ring requested on unconfigured channel 255/255 span 3 Is this likely to be a 1) config error 2) cable issue (I made them) 3) hardware problem with the Digium card 4) software (lib pri) Any clues?

Hi I have done everything richard told to do ECT . below is my trace, anyone can help ? -- DAHDI/i1/09123278669-4 answered DAHDI/i1/88050048-3 -- Native bridging DAHDI/i1/88050048-3 and DAHDI/i1/09123278669-4 PRI Span: 1 Adding facility ie contents to send in FACILITY message: PRI Span: 1 ASN.1 dump PRI Span: 1 Context Specific/C [1 0x01] <A1> Len:11 <0B> PRI Span: 1

Hi All, I've bought a R2Adapter to convert R2Digital to ISDN. I am trying to config E100P card but D-Channel is down. I know R2Adapter uses ETSI ISDN Protocol so I tried unsucessfully setup switchtype to EuroISDN. Any clue? Daniel

We've got a EuroISDN (32 channels) with a TE405p, running cvs head as of 5 days ago. In the past couple of days, we've hit a scenario where incoming calls to the * pbx from the PSTN are being marked as busy, but outgoing calls work just fine. When we reboot *, the problem goes away. Has anyone else had this ? I've attached a PRI debug below. I've changed the phone numbers (x

Hi, As you may know, these ISDN BRI features are very important here in Europe as ISDN Basic Rate Access is very popular among Small & Medium Entreprises. I don't really know why but it seems that in many countries, default is to install small PBX using Point-to-Multipoint (PtMP) mode as opposed to Point-to-Point (PtP) which is the norm for PRI. So basically, in several countries, SME