similar to: Broadcom NetXtremeII and CentOS 6

Displaying 20 results from an estimated 1100 matches similar to: "Broadcom NetXtremeII and CentOS 6"

2009 Dec 14
4
bnx2 losing connectivity
Hoping someone else has seen this before. I have a few dozen Dell R610 systems with CentOS 5.2 that are using kernels from 5.3 and 5.4 (2.6.18-128.1.10.el5 & 2.6.18-164.6.1.el5), that at random lose layer 2 network connectivity either partially or totally. Running tcpdump on the interface reveals only ARP broadcasts, no responses. Switch reports no packets being received on the interface.
2013 Nov 04
0
Compiling Broadcom netxtreme2-7.6.62 drivers Xen4CentOS
Having problems compiling Broadcom netxtreme2-7.6.62 drivers using the Xen4CentOS (http://wiki.centos.org/QaWiki/Xen4) kernel: CentOS release 6.4 (Final) 3.4.61-9.el6.centos.alt.x86_64 I had to modify the Makefile's a little to get to pass the validation since it was referring to kernel 3.0 and 3.5 but not 3.4. But after doing this I still had the following problem: # make make -C bnx2/src
2006 Aug 18
2
Broadcom Corporation NetXtreme II BCM5708 bnx2 bridging problem
Hi, I''ve run into the same issue as: http://lists.xensource.com/archives/html/xen-users/2006-07/msg00599.html In that, running the network bridge script kills networking completely, trying to ping the gateway gives me destination host unreachable. The card is: 09:00.0 Ethernet controller: Broadcom Corporation NetXtreme II BCM5708 Gigabit Ethernet (rev 11) Using the bnx2 module:
2010 Sep 11
1
Network cards not recognised
Hi, We have a HP DL385 G6 server that is having an issue. Two of the 4 network cards are not being recognised by Linux. We have quite a few other servers with the same hardware and no issues but, before I call HP, I would like to make sure that I am not doing anything wrong :) I have tried with the kernel that came with CentOS 5.5 and the updated one kernel-2.6.18-194.11.3. I do an lspci
2012 May 31
0
iSCSI offload with Broadcom NetXtreme II BCM5709.
Hello all. We recently purchased HP Proliant DL380 G7 server and also a HP Lefthand P4500 G2 24TB iSCSI box. The server itself has Quad Ethernet based on the BCM5709 Chipset from Broadcom (NetXtreme II). My main question is about iSCSI offload mechanism, as iSCSI itself is pretty new to me but I have gotten a good hold on it tho. I have managed to setup and configured our Lefthand box into
2010 Nov 15
5
Poor performance on bandwidth, Xen 4.0.1 kernel pvops 2.6.32.24
Hello list, I have two differents installation Xen Hypervisor on two identical physical server, on the same switch : The problem is on my new server (Xen 4.0.1 with pvops kernel 2.6.32.24), I have bad performance on bandwidth I have test with a files copy and "iperf". Result iperf average: Transfert Bandwidth XEN-A -> Windows
2006 Nov 11
1
Broadcom Corporation NetXtreme II BCM5708 bnx2 bridging
I am having the same problem. But, I cannot access to the following link for solution http://wiki.ncsa.uiuc.edu/wiki/Dell_PE1950_NIC_Firmware_Workaround Can someone send me the content of this link? Thanks. Pete, This may be relevant: http://wiki.ncsa.uiuc.edu/wiki/Dell_PE1950_NIC_Firmware_Workaround - Mike At 8/18/2006 09:40 AM Friday, Peter McEvoy wrote: Hi, I''ve run
2011 Sep 09
3
CentOS5 with Dell Broadcom iSCSI Offload, does it work ?
Hi all, After finding multiples answers to this question via google, but without making it work on my servers. Has anybody iSCSI Offload working on a Dell Server with Broadcom NICs ? My environment: I'm running CentOS 5.6 CR, on a Dell PowerEdge R710 with Broadcom Corporation NetXtreme II BCM5709 conecting to an EMC CX4-120 SAN, via 2x Cisco 2960G-24TC-L switches. It's working
2010 Jul 07
2
Bug#588310: Xen enabled kernel cannot find the / partition
Package: xen-hypervisor-3.4-amd64 and linux-image-2.6.32-5-xen-amd64 Version: 3.4.3-1 and 2.6.32-15 Hello all, GRUB-PC does not automatically populate Xen related parameters in /boot/grub/grub.cfg so I added them manually (see below). All the packages involved on my Dell PowerEdge R710 running Debian GNU/Linux Squeeze AMD64 are from the Squeeze repository. There are four (4) 1TB SATA HDD
2009 Oct 23
0
Problems with BCM5709 network
I've just installed CentOS 5.4 on an IBM server with a BCM5709 network adapter, and can't get networking to work. It looks like an appropriate driver (bnx2) is installed, lspci and the system log return sensible info on the unit, there are no specific error message anywhere, but I get "no link present" when I try to activate the device. In other words, I see essentially the
2012 Oct 27
2
Network issue - Windows works but CentOS does not
I am having an extremely strange issue with a BL460c1 (G1) blade on a c7000 enclosure. I could not for the life of me get the machine to ping the gateway or any other blade on the same enclosure (yes, the subnet mask was correct & quadruple-checked); although pinging to the local IP works. I was almost convinced that it was a network or hardware issue; until I asked someone to try
2008 Jan 24
1
Dell 2950 and broadcom
Hi all I'm trying to setup second ethernet on Dell 2950 server but there isn't any eth1 device (in the bios are ON) # dmesg |grep eth eth0: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz found at mem f8000000, IRQ 169, node addr 001c23d878bb eth1: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz found at mem f4000000, IRQ 169, node addr 001c23d878bd
2016 Nov 16
1
BroadCom NIC not adding as PassThrough device
Hi Guys, I am trying to add a Broadcom Physical NIC to a virtual Machine as Passthrough device. However I am getting following error. Error starting domain: unsupported configuration: host doesn't support passthrough of host PCI devices Traceback (most recent call last): File "/usr/share/virt-manager/virtManager/asyncjob.py", line 88, in cb_wrapper
2007 Oct 07
9
RESOLVED: Debian Xen + Broadcom NetXtreme II (IBM x3655 7985-AC1)
I have a new x3655 IBM and whenever the /etc/xen/scripts/network-bridge script starts, the ethernet would no longer work. This post isn''t about the cause, but the fix. I did a lot of tcpdumps and Googling, but I''ll spare you that. All they do is prove that yes, there is an issue. :) I tried Debian 4.0 i386/amd64 and Ubuntu 7.04 Server i386/amd64 and they all exhibit the
2011 May 16
4
Xen enviroment consultation
Hi all, I were upgrading my system recently. But I met some difficult problems, the biggest one is described in http://permalink.gmane.org/gmane.comp.emulators.xen.user/66971, unfortunately I got no answer yet. My original environment is xen3.4.2(64bit) + dom0 kernel 2.6.18-xen, and 4 domus with kernel 2.6.18-xen, after first upgrade stage, I have Xen4.1.0(64bit)+dom0 kernel 2.6.32.39, and 4 domu
2011 May 16
4
Xen enviroment consultation
Hi all, I were upgrading my system recently. But I met some difficult problems, the biggest one is described in http://permalink.gmane.org/gmane.comp.emulators.xen.user/66971, unfortunately I got no answer yet. My original environment is xen3.4.2(64bit) + dom0 kernel 2.6.18-xen, and 4 domus with kernel 2.6.18-xen, after first upgrade stage, I have Xen4.1.0(64bit)+dom0 kernel 2.6.32.39, and 4 domu
2012 Apr 23
4
Latest 6.2 kernel is broken
I just kickstarted a new machine with the latest CentOS 6.2 files, including kernel 2.6.32-220.13.1.el6.x86_64. It came up without network interfaces. dmesg says: bnx2: Broadcom NetXtreme II Gigabit Ethernet Driver bnx2 v2.2.1 (Dec 18, 2011) alloc irq_desc for 36 on node -1 alloc kstat_irqs on node -1 bnx2 0000:01:00.0: PCI INT A -> GSI 36 (level, low) -> IRQ 36 bnx2 0000:01:00.0:
2013 Mar 19
5
Centos 6.3 Network bnx2 Problem on HP DL360
Hello Mailing List I got a severe network error message at a HP DL360 Server. The kernel log says: ----------------------------------- /var/log/messages ----------------------------------------------------------------- Mar 19 15:45:06 server kernel: do_IRQ: 2.168 No irq handler for vector (irq -1) Mar 19 15:45:17 server kernel: bnx2 0000:02:00.1: eth1: DEBUG: intr_sem[0] PCI_CMD[00100446] Mar 19
2007 Oct 26
4
BROADCOM 5708 ON POWER EDGE 1955
Hello, I''ve this strange problem. When Xen kernel start and it try to start eth devices, network doesn''t work. It seems to be a problem with NICs firmware. Anyone had this problem? Do you know where I can download firmware upgrade? (on DELL''s site I''ve just searched...) Thanks, Carlo No virus found in this outgoing message. Checked by AVG Free Edition.
2011 Jun 27
7
bnx2 FTQ issues on 2.6.32 + xen 4.0.1;
Hi Michael: Sorry to brother. But I''ve been suffered this issue quite a long time. My test environment is 2.6.32.36 + xen 4.0.1 + bnx2, 2.3. Also cpu idle is disabled in grub. Grub info: title Red Hat Enterprise Linux Server (2.6.32.36xen) kernel /xen-4.0.1.gz iommu=off x2apic=off console=com1,vga com1=115200,8n1 noreboot cpuidle=0 cpufreq=none