similar to: OT Problem seeing slave drives.

Hi folks, I inherited a very old computer (I guess about 8 years old) which I'd like to use for some training on CentOS. I downloaded images for CentOS 6.4 i386 (DVD 1 and 2) and burned them onto discs. After inserting DVD 1 into drive and booting, on the "Welcome to CentOS 6.4!" screen I select "Install or upgrade an existing system". I then skip the media test and

I am unable to make quadbri board to work in NT mode, in TE mode it works OK. I have set 5 jumpers to NT mode. Dmesg shows everything OK: qozap: Junghanns.NET quadBRI card configured at mem 0xd084e000 IRQ 9 HZ 100 CardID 1 qozap: S/T ports: 4 [ TE TE TE NT ] qozap: 1 multiBRI card(s) in this box, 4 BRI ports total. from Asterisk side seems to be ok. pri show span 4 Primary D-channel: 12 Status:

I am trying to install a TE405P which is to be connected to E1 trunks. I have set the jumpers to E1 (closed), but modprobe wct4xxp still fails with the message: ZT_CHANCONFIG failed for channel 97 - which obviously means the card is still in T1 mode. I have tried everything I can think of, any ideas? TIA

Hi , I'm disperated I've recently installed FreeBSD 4.8 ,and all at the first look was ok , this was only a try in a small partition , and now I have decided to install it in a bigger partition , so I've downloaded the 5.1 ISO (to give it a try too) and I've tried to BURN it with "burncd" . Now, I've noticed that in the DEV directory there are the devices

Hi all, I've got a Junghanns QuadBRI card which I'm going to install on a system in Germany Anyone give me some tips on the Jumper settings? I'm guessing it's going to be NT mode with p2p? I haven't used ISDN before. I'm going to also put a Digium TDM400P card in there to plug the analog phones into. I'm just worried about the jumpers and modes. Suggestions

Hello, I've got a (P)ATA disk in a special frame. The disk itself supports UDMA-100 (and has an 80-ribbon cable), but the frame isn't compatible with that. By default, FreeBSD negotiates UDMA-100, and the console starts to fill with ICRC errors. In the past, I used a patch to ata-all.c that enabled the following entry in loader.conf to force the disk to UDMA-33, so it worked fine:

------ Original Message ------ From: "Tony Kasule" <timotsmith at gmail.com> To: "Asterisk Users Mailing List - Non-Commercial Discussion" <asterisk-users at lists.digium.com> Sent: 30/06/2015 8:34:47 p.m. Subject: Re: [asterisk-users] Help With Physical Layer >Hello, > >Anyone to help me with this issue? It has never worked :( Hi Tony I'm not

?Hola! torisa.c (from zaptel 0.50) says: #define MASTERVAL 0x41 /* Enable E1 master clock on Rev. B board */ Does that mean that there is a torisa revB? If so, are the schematics downloadable from somewhere? (www.zapatatelephony.org only has Rev. A ones) Does the Rev. A support E1? (just changing the DS2151 for DS2153, the DS crystal and closing the E1 jumpers, or something else is

Hi all, I dont know why, but if I plug my PC inside the 'PC' slot on my polycom, this is not working. (Polycom IP600 is online on the net.) I'm using normal network cables. (I see jumpers behind the phone... do I need to play arround with that?) Any help would be appreciated. -- Alexandre Leclerc

I have successfully placed a call into and out of the card from Asterisk using vISDN. The current vISDN snapshot now contains the PCI id's for the card so no patching should be required. Most of the initial testing failure was due to misconfiguration of vISDN by me and a bad entry in my sip.conf resulting in one way audio. So I have established that at least 1 channel of 1 port works in TE

hi All, its probably very simple but i can't find the way to it. i have some b410p cards and use them to connect to ISDN2, this works OK for calling but i need to have 1 line to be send to the fax machine. the fax machine is a modem connected on another machine with hylafax. as far as i can figure out i need to set 1 of the slots, the one leading to the fax, in the b410p in NT mode by

I am looking at having a read only box, it will not use a swap partition. Any recommendations? Well, i tried two possibilities years ago.. 1.) : There are SCSI-Disks with jumpers for "Write Protect" , so you have a real Hardware write-protection. 2.) : Have a look at (Open)BSD's "Immutable Flag"-Feature. (Well, i hope you all love OpenBSD?) ;-) But....don't get

I am having problems with silent data corruption on (some) drives connected to an MCP55 SATA controller. I have two servers, both running RELENG_7_0/amd64. One has the 570 Ultra chipset, the other has 570 SLI. Both chipsets have the MCP55 SATA controller. The server with 570 Ultra chipset has a bunch of older 250GB SATA-150 drives hooked up to the MCP55 controller and it is working just fine.

Hi I've installed CentOS 5.2 (i386) in a computer with a DG33BU motherboard ... When I installed it it crashed because of ACPI issues. Searching Google I found that I need to turn ACPI off in order to successfully install CentOS, which I did. After a while I noticed that because of ACPI is off the Linux kernel finds, initializes and uses only 1 CPU core in the Q6600 quad core CPU that is

Does anyone have any experience ith configureing the sangoma A102 card for testing using a e1 cross cable i've configured and installed the cards properly even the lights on the card are green which proves that my cross cable is properly built too. my problem is with asterisk which gives me these errors PRI got event: HDLC Abort (6)on Primary D-channel of span 1 PRI got event: HDLC Bad FCS

I've just encountered an odd problem with our Digium TE410P card and was wondering if anyone has experienced something similar before. We utilize all 4 ports with 2 of them connected to the PSTN as E1 with the second 2 ports connecting to a device which accepts T1. We are essentially acting as an E1 to T1 converter. This machine has been operational for close to 6 months without a problem.

Hi all, I have a box running asterisk with T410 connected to a Nortel DMS 100 switch and another box running SER with grandstream phones on it So if there is a call from the pstn it goes from the Nortel to the asterisk and then to the SER box and finally to the phones.if the phone is busy or the number is invalid the * box will first send an ALERT message to the Nortel and say the call is going on

I've googled / voip-info'd / searched until my eyes are blurry, but couldn't see the info I was looking for. I've turned here for help! Asterisk CVS head (9/7/04) Fedora Core 2 (updated to 2.6.6 kernel) DE405P (jumpers set to E1) I want to put asterisk in the middle of our current pbx (Meridian Option11) Currently the meridian has a 2MB pri EuroISDN card linked via a rj-45 into

Hello: Will Digital Audio (via EIDE ribbon cables) be supported in the Kernel in CentOS 5.0? I'm now using CentOS 4.4 on a Dell Dimension 2400 box (Celeron 2.6 GHz CPU). This is a dual boot box, rarely booted into Windows XP, but when I do use Windows, and I place an Audio CD into the DVD drive or CD-RW drive, I can hear the music. Using CentOS 4.4, I can see that the software and hardware are

Hi list! I'm trying to setup Digium TE205P E1 card to work with my provider (and Ericsson BP 250 - this comes later). When I execute "pri show span 1" this is what I get. pbxzg1*CLI> zap show status Description Alarms IRQ bpviol CRC4 T2XXP (PCI) Card 0 Span 1 OK 0 0 0 T2XXP (PCI) Card 0 Span 2 UNCONFIGUR 0 0 0 pbxzg1*CLI> pri show span 1 Primary D-channel: 16 Status: