similar to: Adaptec SCSI Card 2930LP supported by CentOS 5.x?

Hi all, I am trying to boot Xen on a Adaptec 7892 SCSI controller and it isn''t even going into the check routines for the disk! (Ie, no disks are found and I can''t boot into Xen...)... It works fine on FC3 and the drivers are compiled into the kernel (I tried both new and old...). The machine is an IBM eSeries 330. Anyone else have it running on a 7892? Thanks, David

Hi. I''ve used ghost for change the ide disk for an array of scsi in raid using an adaptec controller 2110s. Now when I boot it didn''t boot correctly. Looking for in Internet (http://kbase.redhat.com/faq/FAQ_46_4969.shtm) I guest that I have to rebuild the initial ramdisk to contain the proper kernel modules for the adaptec controller. But what is the kernel module for

Hi people I am new to Xen and having some trouble getting it up and running. I am trying to install it on a Dell Poweredge SC420 that has CentOS (RHEL3 clone) installed. The error that I am getting when I first try to boot into the Xen kernel, after having installed the binary and adding the necessary lines to grub.conf is : ---snip--- md: Autodetecting RAID arrays md: autorun ... md: ...

Ravi Srivastava submitted the following Information: Email ravi_prakash at ngri.res.in URL www.ngri.org.in Company National Geophysical Research Institute Location Hyderabad, India Comments Dear All, I am using CentOs 3.5 on a 64 bit Xeon machine. I wanted to install aic7xxx-6.3.9-rhel3.i686.rpm to use DAT 72 but it is giving following error message. Please help to resolve this problem: I took

I have an IDE based PC running Linux/CentOS4 to which I wish to attach a scsi dlt. The host controller is an Adaptec AHA3940 something that lspci reports as: SCSI storage controller: Initio Corporation 360P (rev 02). I would like to have the system load the driver for this adapter at boot but I have two problems: 1. I am not sure which driver to use; and 2. I do not know how to force

I have an Adaptec 392320 Ultra320 SCSI adapter. I am running x86_64 SLES9 SP3. When I build x86_64 Xen with just the 2.6-xen kernel + initrd, I am getting the following error on the module load. But if I go back to building separate xenU and xen0 kernels without initrd the device works without any issues. Any idea what is going wrong here? Am I leaving something out of my initrd? Here is the

Hello, does CentOs 5 supports an Adaptec AHA-2940W/2940UW scsi controller (pci)? Is this controller maybe supported by the aic7xxx driver? I want to install CentOS 5 on my desktop pc but the currently installed pci scsi controller for my scanners (drivers: 2x tmscsim, 1x advansys) are not supported by CentOS. So I am searching for something else. Thanks in advanced. regards Olaf

Hi, Hi, I have been googling, and can't find anything that will help me: mt -f /dev/st0 status /dev/st0: No such device or address Any suggestion? I am using CentOS 3 [RHEL ES3 without the licenses] The tape drive is recognized at boot [from dmesg] scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36 <Adaptec 29160 Ultra160 SCSI adapter> aic7892:

Hello, I am having issues making my box boot with Xen. I am working with linux-2.6.16.28-xen on a gentoo box. The server is Dell PowerEdge 1850 with Perc 4e/Si, FW 521X. When dom0 reaches the point of scanning the SCSI controllers, it hangs in a loop aic7xxx_dev_reset_returns 0x2002. My regular (non-xen) kernels come up fine with detecting my adaptec scsi controller. Had anyone had the same

Hi, Can someone please help me with this? I have just upgraded from 4.7 to 4.8-STABLE and this is what I am getting when I try a tape backup. Please CC as I am not in the list. It was working well before the upgrade (dump -0ua -f - / | gzip -c -9 | dd of=/dev/nsa0). Thank you, Lefteris Tsintjelis Jul 3 22:55:18 ene /kernel:

----- Original Message ----- From: Karl Heyes <karl@pts.tele2.co.uk> To: <icecast@xiph.org> Sent: Friday, January 31, 2003 5:29 PM Subject: Re: [icecast] Re: Compiling ices <p>> On Fri, 2003-01-31 at 06:39, Marc Remijn wrote: > ... > > > Kernel output: > > > > invalid operand: 0000 > > CPU: 0 > > EIP: 0010:[<d08e25b1>]

I am trying to run my old CentOS4.8 (32-bit) system as a guest system under CentOS5.4xen (64-bit). I followed the instructions in Appendix A of the xen user manual (/usr/share/doc/xen-3.0.3/pdf/user.pdf) and created a 'disk image' (actually a 10gig LVM logical volume: sauron.deepsoft.com% sudo fdisk -l /dev/mapper/sauron-c4guest Disk /dev/mapper/sauron-c4guest: 10.7 GB, 10737418240

Hi *, I try to install Xen 3.0.0 on a IBM x342 with a ServeRAID 4Lx controller. The box boots with "plain" 2.6.12.6 (aic7xx- and serveraid-support included). It does not with a similar configuration of 2.6.12.6-xen0. Any hints, boot options? by Töns -- There is no safe distance. _______________________________________________ Xen-users mailing list Xen-users@lists.xensource.com

Is there a way to test if the motherboard is ready for a Digium card (PCI 2.2) ? I would like to know from a remote computer, where I have (root) access, if this computer is ready for a TDM22B. bye Ronald

We are migrating from Fermi Labs linux distro to the Centos 3.6 distro. So far all of the Dell's we have installed on have worked fine but we have two generic servers that are using Tyan Thunder K7X motherboards with built in Adaptec Ultra 160 SCSI using AIC7899 chipset. When we try to install on these systems the install cd seems to lockup loading the AIC7xxx driver. Adaptec says they do not

Hello everybody, After going through multiple posts on Internet and trying different things I can't seems get zaptel wcfxo loaded on the server correctly. I run dual P3 500 Mhz box. After reading README.udev I put a file 60-zaptel.rules /etc/udev/rules.d # Section for zaptel device KERNEL="zapctl", NAME="zap/ctl" KERNEL="zaptimer",

OK, it seems that the kernel I have (stock CentOS 4.7: 2.6.9-78.0.22.EL i686) seems to gronk the nVideo SATA controller in AHCI mode. It is NOT able to deal with the SATA DVD Burner I have. It is a "Sony Optiarc DVD Burner with LightScribe Black SATA Model AD-7241S-0B LightScribe Support". Is there some special magic I need to do? Here is the relevant bit from the boot up (SATA ports

Hello all this is my first post to this list so i would like to than you all in advance for your time and consideration. I am in the process of building a new server and have purchased some used hardware. There seems to be some hardware issuses and i am hoping nothing was damaged during shipping. However i am in contact with intel and we are tring to figure out the exact problem via email. So

I need a SCSI card to attach a tape library to my system. I am looking at the Adaptec 29320A-R. Can anyone confirm that this card will work with the stock CentOS 4 kernel? -- Bowie

Hi All, I need to install CentOS 4.0 x86_64 using Adaptec ASC-29320A with HostRAID enabled, but it seems my card isn't recognized. I've tried to install the hardware using driver downloaded for RHEL 4.0 from the Adaptec Website, but still it's unrecognized. P.S. I'm able to install RedHat 9.0 using this card before. Is there anyone have any solution for this? Thanks and