similar to: fentonups driver patch for Effekta MHD3000 UPS

Hi Henning, you should get in touch with Carlos, who his developing a generic megatec driver (available from svn: http://eu1.networkupstools.org/source.html) Arnaud -- Linux / Unix Expert - MGE UPS SYSTEMS - R&D Dpt Network UPS Tools (NUT) Project Leader - http://www.networkupstools.org/ Debian Developer - http://people.debian.org/~aquette/ OpenSource Developer -

Hi, I am working on a patch for FENTON.H to support some more ups models, I wonder if someone can help with further information,meaning and importance for the following values that are beeing set in the model capability table: float lowvolt; float voltrange; float chrglow; float chrgrange; int lowxfer; int lownorm; int highnorm; int highxfer; Thanks, Nadav

Hello everybody, this is my first post to this list - normally I take some time to read some messages first to get an impression of the List, but I have a pressing question to ask, so please forgive me if I miss the right tone... I just installed NUT 2.0.2 and try to get it working with our Effekta MT 1500. In the Drievers List I found this entry: "Effekta" "MI/MT/MH"

Best fortress support was understandably dropped, but we still use them, and someone else may want the driver I ported to nut-2.0. We also often attach the serial cable from a UPS to a network terminal server, since servers these days don't come with very many serial ports. (They call them "legacy" ports.) I submitted a patch to support these for nut-1.x, and it was rejected

I could not make the bestfortress driver 0.02 work for my Best Fortress LI675VA, so I have made a patch for the driver. The reason was, that all responses are preceded and terminated by CR LF, but the driver would discard everything after the first CR LF. The following patch discards everything up to the first LF. It also adds a debugging feature of displaying the accepted data (level 5 i.e. -D

Hi NUT-Team, I have an effekta MKD1000 USV and I want to connect with NUT over serial device to this USV.I have used blazer_ser as driver but I cannot get a connection to the USV. When I have a look to the driverlist then the effekta MKD1000 is not listed.In a window-System I can connect to the USV with the UPS management system from generex. Can you please help me to connect with NUT to the USV.

Hi all RESTORATION of POWER I seem to have cabling & drivers set up correctly for a contact closure UPS ............as below the logs should indicate that. BUT .......... But after power Restoration between commencement of (shutdown -h +20) ....... & execution of (shutdown -h +20) during the 20 minute wait period of shutdown or whatever the "time" variable is.

Dear Andreas, some googling revealed, you created a driver for the xanto series of online-usv.de. In what state it is currently? I've to manage a S2000 and would like to use nut for it, is it usable by now? Do you need another tester? TIA, Pete

Hi There, i have a strange problem with a fenton powerpal 660. When you switch off the power to the UPS (from the wall), the server (IBM xSeries 203) attached to it dies...However, if you unplug the cable from the server to the UPS and plug it back in again (with the power still out to the UPS), the server starts up again (set to power up after a power failure) and runs with no issues. I have

The patch below adds support for custom HTTP headers in download.file() and url(). My main motivation for this is performing basic http authentication. Some web sites do not support embedding the credentials into the URI itself, they only work if the username and password are sent in the HTTP headers. In fact specifying the username and password in the URI has been

Hi there Would anybody happen to know the correct driver for a Fenton Powerpal S series? upsdrvctl reports: Network UPS Tools - UPS driver controller 1.2.2 Network UPS Tools - Fenton UPS driver 0.90 (1.2.2) Unknown ups - please report this ID string: #FENTON S Series V4.04EG503 Detected Unknown Series on /dev/ttyS0 Alternatively, does anyone know if the manufacturer is likely to

Hi Patrick, 2006/4/2, Patrick Beard <p.beard@blueyonder.co.uk>: > Hi Arnaud, > > Just wanted to let you know the the Belkin F6H500ukUNV is working for me > with the fentonups driver. > > http://catalog.belkin.com/IWCatSectionView.process?IWAction=Load&Merchant_Id=&Section_Id=202840 > > I originally tried it with the genericups driver with upstype=7 but this

Hi There, Running on debian sarge. This was working a while ago, but here goes.. When viewing the upsstats.cgi page, im getting a message "Not Supported" in the Model column with a "ONLINE" message, but no other stats. Here is the syslog when booting nut: Oct 15 14:28:40 mx1 upsmon[4835]: Signal 15: exiting Oct 15 14:28:40 mx1 upsmon[4834]: upsmon parent: read: Success Oct

Hi everybody, following UPS is successfuly tested. Model: FSP Champ Tower 1k https://www.fsp-europe.com/CS/champ-tower-series-1k2k3k/ lsusb: Bus 002 Device 004: ID 0665:5161 Cypress Semiconductor USB to Serial ups.conf: [powerpal]     driver = blazer_usb     port = /dev/hidraw0 Mode = standalone Distro = CentOS 8 What I did to get UPS communicate. In terminal run as root: ln -s

Hi, I have a Fenton Powerpal L660, when I try and configure nut with either the metatec or fentonups driver, and start upsd, the UPS instantly turns itself off. It used to work, until I changed my motherboard and CPU, which means it has a different bios and serial port setup. This is happening with Nut 2.0.1 and also Nut 2.0.5. I have an AMD64 bit processor, Mandriva 2007 64 bit. Any

Gidday all - I'm a new user to nut. I've got some cheap powerpal UPSs working fairly well. However I also have a new Dynamix UPS-1700D and an old Powercom KIN-1700 something unit that I cannot make work right. The best method I've found is "trial and error" which sounds a bit last-resort. Is there any better way to find out what protocol is used? -- Criggie

2007/2/19, Glen Ogilvie <nelg@linuxsolutions.co.nz>: > Hi, > > I have a Fenton Powerpal L660, when I try and configure nut with either the > metatec or fentonups driver, and start upsd, the UPS instantly turns itself > off. > > It used to work, until I changed my motherboard and CPU, which means it has > a different bios and serial port setup. > > This is

2007/2/19, Glen Ogilvie <nelg@linuxsolutions.co.nz>: > Hi, > > I have a Fenton Powerpal L660, when I try and configure nut with either the > metatec or fentonups driver, and start upsd, the UPS instantly turns itself > off. > > It used to work, until I changed my motherboard and CPU, which means it has > a different bios and serial port setup. > > This is

Hi all... I've tested my installation and everything seems OK, but I'll note a couple of things. System is debian, UPS is Fenton Powerpal 660 L First of all, the ups software did not restart because I had not changed 'no' to 'yes' in /etc/default/nut. Maybe it's a debian thing, I don't know. But I don't remember seeing it noted anywhere in nut docs.

Hi, I'm trying to get an Effekta UPS (works directly with blazer_ser) working behind a seriell to ethernet converter (Brainboxes ES-246). I've set the converter to 2400 baud, 8N1, no flow control. On the linux side I started socat and blazer_ser. All I got are timeouts after 12 seconds. I can see network traffic with tcpdump but I've no idea what to do to get this working. Does