similar to: Log message.

Hi. Have back-ported the bcmxcp and bcmxcp_usb driver from Development. I hope it's done right. Tested a clean cvs fetch after commit and it build and install ok. Regards Kjell

Ok Guillaume, It is Megatec protocol. It sends Q1<cr> and answers with (227.2 227.2 227.2 038 50.1 13.5 25.0 00001001<cr> And if you check http://eu1.networkupstools.org/protocols/megatec.html it matches. And now, ho has time to code ? Kjell fre 2006-04-21 klockan 17:18 +0200 skrev Guillaume JAOUEN: > Hello, > > As I wish to help you the most I can in order to get a

Hi, Need to get an answer to the following. I find the naming to be little redundant regarding the 'input.transfer.boost.low - hige'. The same goes for input.transfer.trim.low - high. As I find it, there is only one point where the boost or buck (trim) kicks in. Let's say that the nominal voltage is 230 volt, then we have a input.transfer.boost point on say 220 volt. If the

[was: svn commit r915 - in trunk: . drivers] Hi Kjell, sorry, I'm still much late in emptying my mail stack... 2007/5/25, Kjell Claesson <kjell.claesson at epost.tidanet.se>: > Den Friday 25 May 2007 08.52.20 skrev Arnaud Quette: > > > > I would be interested in some more info: > > - lshal -u <your device's UDI> > > the UDI can be obtained for ex.

I'm pleased to announce that Kjell Claesson has joined the NUT Team. Kjell will work as a developer on bcmxcp and 3 phases UPS support. Thanks you Kjell for your continued support, Arnaud -- Linux / Unix Expert - MGE UPS SYSTEMS - R&D Dpt Network UPS Tools (NUT) Project Leader - http://www.networkupstools.org/ Debian Developer - http://people.debian.org/~aquette/ OpenSource Developer -

OK Eric, Den Tuesday 22 May 2007 08.56.08 skrev Eric S. Raymond: > Kjell Claesson <kjell.claesson at epost.tidanet.se>: > > Or install the udev rules and replug the ups. > > Did that. Manual startup of the driver now works without -u root, > indicating (I think) that the udev rools are doing their job. This >

Citeren Kjell Claesson <keyson-guest op alioth.debian.org>: > Author: keyson-guest > Date: Mon Mar 23 17:37:37 2009 > New Revision: 1817 > > Log: > data/driver.list, add Eaton Powerware 9130 compatibility with bcmxcp > and usbhid-ups. 1) Is this really true? I would have expected that this device would be supported through bcmxcp (serial) and bcmxcp_usb (USB), like

Hi, Got this mail. It looks like he has a ups with revision before K, and need another startup. The 'PW_SET_REQ_ONLY_MODE' is not implemented, so to make it work we have to follow the protocol and send a 'PW_ID_BLOCK_REQ'. This in comsetup of bcmxcp_ser.c Also the standard id block ends with 'Statistics Map', so we have to Skip after reading the length of the 'Size

Hi all! I've been (very) out of the loop for a while, up to the point that I had completely missed that the mailing list has moved. Oh well. However, Kjell Claesson poked at me regarding the 3phase stuff, so I found out that I had missed the recent events. In any case, it seems that the situation is unchanged regarding 3phase support. As some of you remember I made a suggestion for a

Hi Kjell, a few notes: - you should bump the DRV_VERSION upon every change - you should track the drivers TODO list in a comment header (such as "implement smart load segment detection" completed with your info, ...). That would help to bootstrap new contributors. - you can also use the alioth trackers (features request, or task) to give some external visibility on what remains to be

Hi, I recently downgraded my kernel to 2.4 series (2.4.32-rc2). Now I can't get nut running. It was fine with 2.6.14. It say's: --------------------- # ./bcmxcp_usb -uroot AUTO Network UPS Tools - BCMXCP UPS driver 0.10 (2.1.0) Can't reset POWERWARE USB endpoint Unable to find POWERWARE UPS device on USB bus ... --------------------- I've straced it in nut_usb.c

Hi, Made a test build of the Testing branch. The problem is that upsmon and upsc is not respecting the revision change of libupsclient.so. It is now libupsclient.so.1, but i get this. /usr/sbin/upsmon: error while loading shared libraries: libupsclient.so.0: cannot open shared object file: No such file or directory and: upsc: error while loading shared libraries: libupsclient.so.0: cannot

please tell me how i can use the hyperterminal to calibiration of my ups sua 1000VA. nut-upsdev-request@lists.alioth.debian.org wrote: Send Nut-upsdev mailing list submissions to nut-upsdev@lists.alioth.debian.org To subscribe or unsubscribe via the World Wide Web, visit http://lists.alioth.debian.org/mailman/listinfo/nut-upsdev or, via email, send a message with subject or body

Ok, I installed the ups, and installed nut, and /proc/bus/usb/devices says this T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=1.5 MxCh= 0 D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=06da ProdID=0002 Rev= 0.01 S: Manufacturer=POWERWARE S: Product=Powerware UPS C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr= 20mA I: If#= 0 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=00 Prot=00

On 5/23/07, Kjell Claesson <keyson-guest at alioth.debian.org> wrote: > Author: keyson-guest > Date: Wed May 23 21:12:51 2007 > New Revision: 915 > > Log: > - Enabled requested Alarm function in bcmxcp.c > > Modified: > trunk/ChangeLog > trunk/drivers/bcmxcp.c Looks like this breaks when HAL is enabled. At the end of:

tisdagen den 2 juli 2013 20.24.47 skrev Alf H?gemark: > Hi > Hi Alf, > I have the following UPS : > ups.mfr: Eaton > ups.model: POWERWARE UPS 500i > ups.power.nominal: 500 > > It is using the bcmxcp_usb driver. > > I started the driver with debug options, and noticed the following for > the meter map : > > 0.475625 0027 0000 51

On Jul 2, 2013, at 5:16 PM, Kjell Claesson wrote: >> I hope other people can also test this. >> >> Regards >> Alf Hogemark > > Due to some crashes on the disks and lack of time I don't have the git on the > pc now. But maybe some other can commit this. I'd like to ask people to specifically try the bcmxcp branch on GitHub - it includes some changes

Hi all, Have a strange behaviour that I don't know how to debug. This is when I use the Eaton PW5125 ups. I have it connected And running in standby. Starting up the drivers (pw3105 and pw5125) and they run. Start up the upsd and can read info from both of them. The 3105 is supplying the computer and the 5125 have a dummy load. The 5125 is showing that it is off line. Now when I hit the on

Hi all, Arjen can you enlighten me about the function of the blazer upsdrv_shutdown function. I think they are in the wrong order. Regards Kjell

tisdagen den 1 december 2015 09.14.59 skrev Marks, Connor: Hi Marks. > Yes I do have Linux. I have assigned the ups.conf file as seen below.. > > [testups] > Driver = usbhid-ups > Port = /dev/ttyUSB0 > You need to change the driver to mge-shut (hid over serial). Regards Kjell Claesson