similar to: Powercom issues in NUT (was: PowerCom BNT2000AT ups on nut 2.6.0 - second try)

Hi! Normally nut was just worked and worked for me! Not this time though! Distro is Gentoo withe latest nut-2.6.0 emerged today. Linux kernel version is 2.6.36 UPS is PowerCom BNT2000AT "Driver" is powercom ups.conf looks like this! Okay so APC1 is not and APC! [APC1] driver = powercom type = BNT port = /dev/ttyS1 numOfBytesFromUPS = 16

Hi! Normally nut was just worked and worked for me! Not this time though! Distro is Gentoo withe latest nut-2.6.0 emerged today. Linux kernel version is 2.6.36 UPS is PowerCom BNT2000AT "Driver" is powercom ups.conf looks like this! Okay so APC1 is not and APC! [APC1] driver = powercom type = BNT port = /dev/ttyS1 numOfBytesFromUPS = 16

Hi, I have a little problem with PowerCom BNT600AP after running driver I see: root@rask> powercom -D /dev/ttyS1 Network UPS Tools - PowerCom and similars protocol UPS driver $ Revision: 0.5 $ (2.0.2) debug level is '1' Values of arguments: manufacturer : 'PowerCom' model name : 'Unknown' serial number : 'Unknown' line

Hi, I know it's been a topic many times here, but I've searched the archives, googled for days, and I simply don't believe, that there is still no solution to this. I'm using a PowerCom BNT-600AP ups with usb port. I've downloaded the latest version from svn, compiled it, and tried to use it: * megatec(_usb) - no luck, it did not find the UPS (I?ve read in this list, that

All, I'm using the Powercom driver from 2.2 (not the one recently mailed to thelist). Since it's a KIN2200AP, I'm using the driver settings right from the manpage. All the values look "sane" when I'm on-line, but note some of the odd values (<-- Here) when on battery: Also, does anyone know if this UPS supports logging of the "boost" or

I just bought an Ultra UPS system for my linux server, and I need help getting it set up. It's an Ultra 700VA UPS. NUT INFORMATION: Package (apt-get install nut) NUT VERSION: Latest Driver: I don't have one? Here's the device information from my syslog: Code: Jul 7 23:25:27 eric-desktop kernel: [ 3045.609066] usb 2-1: USB disconnect, address 3 Jul 7 23:25:30 eric-desktop

Hey all, Finally got around to hooking up my Powercom BNT-1500AP to nut. It's the old serial interface. Connects okay and gets most information, but a couple of data are way off. Any config recommendations or upgrade recommended? I've played with config a little, but no hits yet. Details: NUT version 2.4.3 ups.conf: [ups] driver = powercom port = /dev/ttyS0

Hello again! Sorry for not being able to test this before. Ulisses, please apply the patch to fix typo in my e-mail address. I've compiled it against nut-2.6.5 about 10 hours ago. It was everything fine until now. I'm seeing CHRG but the ups led wasn't blinking at all. Vendor software was strangely showing charging also. I am assuming this is expected behavior. I've set the

Use the name from ups.conf in front of "@localhost". ?The re?sult is quite different ;) root at artu:~# upsc Elit at artu Init SSL without certificate database Error: Driver not connected > What if you try nutdrv_qx without specifying megatec? (It should > autodetect.) > ?Here is the result: ? root at artu:~# upsdrvctl start Network UPS Tools - UPS driver controller

Merry Christmas to you all and best wishes! I ran into exactly the same problem as described. OS: FreeBSD 9.0-Rel UPS: Eaton E-Series NV 600H NUT: from Ports, nut-2.6.5_1 driver: blazer_usb I am sure the problem is not permission-related as it occurs even when the driver runs as root. My tested recipe for USB permissions is: 1. run usbconfig to find where the device is connected. In my case:

Hey all, I ended up picking up the module listed in Subject line. I switched over my config but apparently not all going smoothly. My config is: [office] driver = powerpanel port = /dev/ttyS0 desc = "Office UPS" When I test the driver running power-panel as a test, I get: > [root at cornelius init.d]# powerpanel -a office -D -D -D -D >

I have a TDM400. Just updated Fedora 12 to kernel 2.6.32. Rebuilt and installed dahdi-2.2.1. kernel modules loaded. lsmod | grep wctdm wctdm 37233 0 dahdi 194985 1 wctdm lsmod | grep dahdi dahdi 194985 1 wctdm crc_ccitt 1549 2 dahdi,isdnhdlc dmesg: dahdi: Telephony Interface Registered on major 196 dahdi: Version: 2.2.1

[As posted as Ubuntu Question #184284 on Launchpad] Hi, I try to set up nut (2.4.3) on my Lucid (10.04.3 LTS) to make use of my old but very trusty UPS (Best Power Fortress 660 LI). Yes, this UPS is old (about 16 years), but with its third battery pack last week it is as good as new. It runs perfectly well with Windows XP, Vista and even Windows 7. But not so with Ubuntu and nut. After

Hi list, on my previous (lenny or squeeze) machine, I had it up and running, but that machine and configs are gone - and on my new jessie machine (see device and config details below) I cannot start the driver: # /lib/nut/bestups -DDDDD -a Patriot_Pro_II_750 0.000000 debug level is '5' 0.000806 send_to_all: SETINFO device.type "ups" 0.000842 send_to_all:

Good afternoon. I try to put nut on gentoo. Has executed installation by a standard command emerge nut. All has passed successfully. I use UPS POWERCOM BNT-1500AP. It is connected to serial port 1, i.e. for my system it/dev/tts/0. In/etc/nut/ups.conf [powercom] driver = powercom port = /dev/tts/0 desc = "PowerCom BNT-1500AP on IP-PBX" modelname = "BNT-1500AP" linevoltage = 230

On Mar 5, 2015, at 2:34 AM, Jakub <jakub.scepka at gmail.com> wrote: > Come on, it started to be interesting! Do you have one of these UPSes? If so, here was Dan's email about a branch to test: > If you still can't get it to work with nutdrv_atcl_usb, another > approach could be worth considering. > > Since this UPS seems to be supported by UPSmart2000I, it could

On Thu, Jun 26, 2014 at 10:20 PM, Steve Ballantyne <steve.ballantyne at gmail.com> wrote: >> However, we don't have all of the 09AE/0001 protocols decoded in the >> tripplite_usb driver. > > I can try to help out on this front? :-) Definitely. >> > 9.783126 Unknown input voltage range: 0x02 >> > 9.783308 Unknown number of switchable

Hello all, been 5 years since I posted on this list, glad to be back :) I have a number of X-power Tigra 1kVA online UPS units. From some knowledgeable folks working for the local distributor, I learnt that from inside this looked like a Best 610 ups unit. Before, I had this UPS hooked via serial to my Windows 2003 server. For monitoring, some winpilot/upspilot software was also provided.

Hello, i've a problem, this is my configuration: - Atlantis Land UPS with serial port - a generic RS232 to USB cable adapter (QinHeng Electronics HL-340 USB-Serial adapter for linux). The problem is in the syslog file where i find: [...] Aug 19 09:07:25 ProLiant megatec[1126]: Communications with UPS lost: No status from UPS. Aug 19 09:07:26 ProLiant megatec[1126]: Communications with UPS

Hello to all list members, I'm trying to make my UPS work with nut-2.2.2 (using Debian Testing, but compiled from source code) for a week ago, with not success. It's a Unitek Alpha 1000Ps, and I supossed it would work with megatec_usb driver, as other Unitek models. It has an USB interface, and when I plug it into my system I've got this message: chopito:/home/jordi# dmesg | tail