similar to: UPS Support

Displaying 20 results from an estimated 1100 matches similar to: "UPS Support"

2007 Apr 12
1
APC 1500 USB problem
Hello, We have two APC Back-UPS RS 1500 USB stuff, and i've got a bit of a problem with it and NUT. The usbdevs output: addr 2: Back-UPS RS 1500 FW:8.g8 .I USB FW:g8, American Power Conversion addr 3: Back-UPS RS 1500 FW:8.g8 .I USB FW:g8, American Power Conversion (UPS1 and UPS2) I've configured our NUT system to monitor the UPSes, and it went very fine till the time had arrived for a
2009 Nov 15
3
two MGE Ellipse 1500 ups via usb
Hi, I've got two MGE Ellipse 1500 UPS connected via usb to an ubuntu jaunty system with nut and libupsclient1 2.4.1-2ubuntu4. As soon as I start the driver for the second one, they start fighting each other and I get no data. I found an older post to this list that said: If you want to monitor multiple UPSes through usbhid-ups, you *must* make sure that each one can be uniquely identified
2009 May 05
5
upsd flapping in the breeze
Hi, I have had a long standing problem with NUT talking to 110V MGE UPSs on FreeBSD, I was recently investigating again and noticed that upsd seems overly noisy, eg.. May 5 03:50:36 egbert upsd[96662]: UPS [ups1] data is no longer stale May 5 03:50:36 egbert upsd[96662]: Data for UPS [ups1] is stale - check driver May 5 03:50:36 egbert upsd[96662]: UPS [ups1] data is no longer stale May 5
2013 Oct 09
2
Updated to 2.6.5, previously-working APC SmartUPS now fails completely
(Note that I mentioned this *was* previously working with an older version of Nut). [irs2-ups1] driver = snmp-ups port = irs2-ups1.sum.naoj.org mibs = auto community = private irs2-ups1.sum.naoj.org responds to pings. On Tue, Oct 8, 2013 at 3:55 PM, Tim Rice <tim at multitalents.net> wrote: > On Tue, 8 Oct 2013, Philip Tait wrote: > > > Here is the upsc
2007 Apr 20
2
Multiple UPS monitoring, relaying
Hello, I've got a setup with NUT, where we've got two UPSes, ups1 and ups2. UPS1 supports our servers, while UPS2 supports our desktop boxes. We monitor both of them via USB on a box now called "upsmon". The interesting point comes here. We monitor both UPSes on the upsmon box, but if UPS2 fails, which supports our desktop boxes, NUT shouldn't initiate a shutdown in
2008 Jul 22
1
MGE Pulsar EX1500 RT comms problem
Hi, I have the above UPS connected to a FreeBSD 6.2 box and it shows 'data stale' very frequently (every few minutes). I have tried the usual trick of setting maxage, poll interval, etc etc but to no avail. When I wind up logging I see (on mge-shut) entering shut_get_report(id: 0d, len: 1800) shut_wait_ack(): ACK received entering shut_get_report(id: 16, len: 1800) shut_wait_ack():
2013 Oct 09
0
Updated to 2.6.5, previously-working APC SmartUPS now fails completely
On Tue, 8 Oct 2013, Philip Tait wrote: > Here is the upsc output: > > # /usr/local/ups/bin/snmp-ups -DD -a irs2-ups1 > Network UPS Tools - Generic SNMP UPS driver 0.68 (2.6.5) > 0.000000 debug level is '2' > 0.000327 SNMP UPS driver : entering upsdrv_initups() [snip] > 4.457750 No supported device detected I'm using a APC smart ups with a
2007 Apr 20
1
USB problem as user
Hello I'm having a bit of a trouble to set up a Back-UPS on a production box. We're using the newhidups driver for this module here, in the office, and I'd like to monitor the one, out in our server farm. The situation is the following: # /lib/nut/newhidups -u root -DD -a ups1 2> ups1.out Network UPS Tools: 0.28 USB communication driver 0.28 - core 0.30 (2.0.5) this one worked
2017 Nov 30
2
SNMPv3 fails when more than one UPS is configured in ups.conf
New NUT install dealing with three APC Smart-UPS 5000s, two of which have AP9617 and the third has a AP9619 card. The SNMPv3 configurations on all three are exactly the same. This is confirmed by snmpget calls that work just fine: snmpget -Cf -v3 -u [...] -l authPriv -A '[...]' -X '[...]' -a MD5 -x DES [upsname] .1.3.6.1.4.1.318.1.1.1.1.1.1.0 snmp-ups can query all three
2012 Mar 04
2
NUT Two Apc UPSes on Windows
Hi, I've got a question about managing two UPSes under NUT. I have two similar model APC usb-connected UPSes to work with, but don't know how to manage them simultaneously from under Windows. Long story short, my ups.conf looks like this: --- ups.conf --- [ups1] driver= usbhid-ups port= auto serial=AS1054340323 [ups2] driver= usbhid-ups port= auto serial=AS1026662626 ---
2013 Oct 09
2
Updated to 2.6.5, previously-working APC SmartUPS now fails completely
Here is the upsc output: # /usr/local/ups/bin/snmp-ups -DD -a irs2-ups1 Network UPS Tools - Generic SNMP UPS driver 0.68 (2.6.5) 0.000000 debug level is '2' 0.000327 SNMP UPS driver : entering upsdrv_initups() 0.000341 SNMP UPS driver : entering nut_snmp_init(snmp-ups) 0.056112 SNMP UPS driver : entering load_mib2nut(auto) 0.056126 trying the new
2007 Feb 07
1
Network Management Card (MGE) 66102 with snmp-ups
I'm trying to set up nut with a MGE UPS equiupped with a network management card, but encountered a problem. UPS: MGE Pulsar M 3000 Network Management card (installed in the UPS): 66102 (2006 edition) Operating system: FreeBSD Nut port version: 2.0.5 Nut driver: snmp-ups According to MGE in Norway this card is supported by nut, but only the old version of the card (66244) is listed on
2005 Dec 24
1
Regular expressions in upssched.conf?
Hi, I didn't found an answer for my question in NUT documentation/FAQ or this mailing list archive so I?m posting it here. I want to start a timer only if both of my UPSes remain on battery. Not just one, both. My UPSes are: - ups1@host-a - ups2@host-b Is it possible to use something like this in upssched.conf? AT ONBATT ups1.* && ups2.* START-TIMER onbattwarn 180 Thanks,
2009 May 30
2
APC USB UPS vs FreeBSD 6.x
Hi, I have a customer who just bought an APC Back-UPS XS 1300 LCD and I thought I'd try the latest NUT with it (on an old-ish FreeBSD 6.x system). It sees the UPS but I can't actually query it for data, in the usbhid-ups debug output I see.. 30.840512 HIDGetEvents: failed to buffer report: Result too large 30.840600 Got -34 HID objects... 30.840681 Quick update...
2012 Dec 11
2
Smart1500LCD USB and usbhid-ups
Greetings all, Anyone have a clue on this behavior (see below) on this behavior with FreeNAS-8.3.0-RELEASE-x64 (r12701M) on a TrippLite 1500LCD UPS? NUT version is 2.6.5 Using the following profile: Tripp-Lite ups 2 Smart1500LCD USB (usbhid-ups) I get the following: Dec 10 21:40:12 nas6 kernel: uhid0: <Tripp Lite TRIPP LITE UPS, class 0/0, rev 1.10/0.02, addr 2> on usbus1 Dec 10 21:40:12
2006 May 09
3
Eaton Powerware 5110 UPS
Hi, I am wanting to use NUT to connect to an Eaton Powerware 5110 UPS using USB to connect. - I am using NUT 2.0.2 - I have compiled it with USB support - I can see that the UPS is registered as connecting in /var/log/messages eg usb 3-1: USB disconnect, address 3 usb 3-2: new low speed USB device using uhci_hcd and address 4 But I don't know how to progress from here.
2019 Dec 25
1
NUT not shutting down one of three UPSs (sometimes none of them shut down)
I have three APC SmartUPS 5000s. Two of them are AP9617 and one is AP9619. I have a RS-232 connections from my monitor host to all three. All three report status and give information. One of the two AP9617 - ups3-1 - does not shut down when FSD is sent. It did when I first set this system up a year or two ago but it's stopped doing so since then. Resetting the management interface does not
2012 May 10
3
battery.charge and other fixes needed for X-Power Tigra 1kVA
Hello all, been 5 years since I posted on this list, glad to be back :) I have a number of X-power Tigra 1kVA online UPS units. From some knowledgeable folks working for the local distributor, I learnt that from inside this looked like a Best 610 ups unit. Before, I had this UPS hooked via serial to my Windows 2003 server. For monitoring, some winpilot/upspilot software was also provided.
2017 Dec 04
2
SNMPv3 fails when more than one UPS is configured in ups.conf
Hi Charles, Running upsdrvctl -D start on the host with all three configured to SNMPv3 kicks out 56 different "unhandled ASN 0x81 from ..." lines on all three but importantly they all start up and keep running. I'm starting to suspect the startup is taking so long that systemd is timing out and killing it. time -p reports real time of 133.27. I'm not a fan of systemd but
2024 Oct 18
2
NUT 2.8.0-7 Can't claim USB device [2341:8036]@2/0: Invalid parameter using usbhid-ups
Hello All, I have been trying to get NUT package working on proxmox host with Arduino HIDPowerDevice (https://github.com/abratchik/HIDPowerDevice) And I have been banding my head against the wall and looking through the internet why I am getting "Can't claim USB device [2341:8036]@2/0: Invalid parameter" error, but could not find anything relevant. The information : - OS name