similar to: Plexus UPS on a QNAP NAS

Hi, Another beginner question. I spend hours trying to find the solution for how to configure winnut properly but I' struggling to make it work. I want my QNAP NAS TS-231 to work as a master and send signal to the PC to shut it down during power outage. I configured QNAP properly (like this: http://geekbeat.tv/qnap-adding-external-devices-qnap), but I don't know what to do next. I work

Now I have this in /etc/nut/upsmon.conf (my QNAP NAS wants admin and 123456 or not working) RUN_AS_USER root MONITOR qnapups at localhost 1 admin 123456 master MONITOR qnapups at 192.168.222.252 3493 admin 123456 slave MINSUPPLIES 1 SHUTDOWNCMD "/sbin/shutdown -h +0" POLLFREQ 5 POLLFREQALERT 5 HOSTSYNC 15 DEADTIME 15 POWERDOWNFLAG /etc/killpower NOTIFYFLAG ONLINE SYSLOG+EXEC

I've searched for quite some time and read the FAQ, but to no avail. I have a UPS connected to a NAS. Unfortunately I have to specify every single client IP (ups slave), because the stupid NAS system (QNAP) does not allow me to set a /16 or /24. Changing the config files manually does not work either, because the service won't come up anymore. (One has to love QNAP at this point.) Thus I

Hello, Just baught this ups to replace an Ellipse. I've had a look at the nut hardware compatibility list, it's fully compatible and uses the same driver as ellipse (usbhid-ups) Here is the error I get when I "/usr/bin/upsdrvctl start" : Network UPS Tools - UPS driver controller 2.6.5-Unversioned directory Network UPS Tools - Generic HID driver 0.37 (2.6.5-Unversioned

Hi, all! I sucessfully install NUT by source, but it could not recognize my UPS device My UPS device is APC Smart-UPS 750VA USB & Serial 230V for China. Pruduct introduction: http://www.apc.com/products/resource/include/techspec_index.cfm?base_sku=SUA750ICH The page is in Chinese. It may be similar with this one:

I have a freshly built, updated EL6 system and am having problems with USB stability - at boot everything works fine but within a few hours, USB devices start disappearing randomly. At first I though the USB devices were suspect, but removing the suspect devices and an accessory PCIE USB card hasn't changed anything. As of now, a single USB device is working. (which is lucky, it hosts the

Hello, I'm trying to setup a UPS configuration whereas I have one physical UPS but two UPS entities loaded by the system used by different network slaves. In my ups.conf configuration I have ... [ups] driver = apcsmart port = /dev/ttyS0 desc = "APC UPS" [qnapups] driver = dummy-ups port = ups at localhost desc = "APC UPS for

Hello, I'm currently stuck with a QNAP NAS appliance (don't buy this !) I have a Sernet Samba 4.5 as an AD controller and my QNAP have a Samba 4.0.25 (latest update) All i want is to join the QNAP to the AD, the QNAP will act as the file server. The join in the official way is okay but the uid / gid mapping is f*cked. I tried almost everything, change the idmap,

Hello, first of all - thanks for creating tinc! It has become an invaluable tool for me to securely join a multitude of servers and clients through a VPN. Today, I was trying to compile Tinc 1.0.12 on my newly purchased x86 Linux-based QNAP TS-239 Pro NAS device (Kernel 2.6.30.6). The configure-script finishes without error (see attached config.log). However, configure.status fails with

I am not sure where I should even begin troubleshooting this. I know a little bit about Linux and am comfortable editing files and running commands however definitely not a Linux guru. I have ipkg already installed on the QNAP. I know absolutely nothing about ruby on rails. Thanks for any help. For those that are not familiar with a QNAP, ipkg is the same as apt-get or yum in some Linux

Hi! Some systems I have take some time to shut down, so I would like them to shut down if the UPS have been on battery for 2 minutes. Internet has told me that SHUTDOWNCMD ?/sbin/shutdown -h +0? in /etc/nut/upsmon.conf will execute when the UPS is both OB (on battery) and LB (Low battery). Like in wiki.ipfire.org - Detailed NUT Configuration<https://wiki.ipfire.org/addons/nut/detailed>

Hi Greg, Thomas and the list, I've not forgotten you nor your issue. It just took some time to gather a "faulty" unit and a bit of time to reproduce your issue. The good news is that I've commited a fix to the NUT development branch (aka Subversion), in the release r2015. The bad news is that your test and feedback is welcome ;-) For more info on getting and compiling the

Hi all, First off thanks you for such a great tool - my searching so far indicates that the developers and community behind nut are committed and doing a great job! Background: I've just purchased a Plexus 500VA UPS for ebuyer because it was cheap. I didnt expect much but I've seen a few references to people getting the same and similar models to work with NUT so was encouraged to try!

Good day. Can not perform shutdowns Ups. Please help. Details of our installation are: OS: Turris Omnia (TO) NUT version: 2.7.4-5 Installation method: from package UPS device: EATON UPS 5SC 500i , 230V, 350W, 500VA, USB bought in jun 2018 If you connect to TO UPS via USB, the /dev/hidraw0 device will be created. No any programs from NUT package is not running. When I run: /lib/nut/usbhid-ups

Hi, I have Lenovo laptop with an Intel wireless and Bluetooth adapter, running CentOS 6.9. The wireless works just fine, but I can't seem to get Bluetooth to work. When I try to force it up from the command line I get # hciconfig hci0 up Can't init device hci0: Invalid request code (56) There is also a similar message message in /var/log/messages from start-up on boot. The device

Hi folks, for some time I used a HP 2840 AiO device, connected via LAN, to scan documents. As scanning application I use xsane. I want to replace that HP scanner by a CanoScan LiDE 210. # LANG="" yum info libsane-hpaio ... Installed Packages Name : libsane-hpaio Arch : x86_64 Version : 3.14.6 Release : 3.el6 Size : 148 k Repo : installed From repo

Hi All, I have a WD RE4-GP which dropped an Adaptec 51645 RAID controller. I ran a smartctl short test on the drive and it failed with a read error. So I ran the Western Digital's own diagnostic software (DLGDIAG), both the short and extended test on the drive and it passed with no errors. So I ran the smartctl short test again and again it failed. I then ran smartctl long test and that

Hi, i've got similar problem with an OVISLINK 1000VA UPS on Debian. I've tried to connect with it using different drivers and this is what I get with each of them: [UPS] driver = blazer_usb vendorid = 0001 productid = 0000 port = auto subdriver = phoenix sweethome:~# /lib/nut/blazer_usb -a UPS -u root -DDD Network UPS Tools - Megatec/Q1 protocol USB driver 0.08 (2.6.4) 0.000000

On Sep 12, 2013, at 7:47 PM, Derek Rachul <drachul at gmail.com> wrote: > I tried reversing the order of the definitions in the config file, and it does seem to change the order in which they're loaded (at least according to the system logs) however the error remains. I don't have any experience using the dummy-ups driver on the same host as the real UPS driver, so this is a

CentOS Errata and Security Advisory 2018:1836 Important Upstream details at : https://access.redhat.com/errata/RHSA-2018:1836 The following updated files have been uploaded and are currently syncing to the mirrors: ( sha256sum Filename ) x86_64: 9c26560f7b175d6e1455a7b9edf9c56be74c06a98f91074a36c3944a51ea110e plexus-archiver-2.4.2-5.el7_5.noarch.rpm