similar to: APC Smart-UPS 3000XL: Compatible/Any good?

Perhaps someone else could confirm this, I have an APC UPS with a built-in network management card with environmental sensor for temp/humidity. The OID index for the sensors appears to be .1 (the last component for each of the OIDs listed below). The original source code has them at .0 drivers/apccmib.h #define APCC_OID_IEM_TEMP ".1.3.6.1.4.1.318.1.1.10.2.3.2.1.4.1" #define

* Is there a way to configure NUT so that it recognizes the huge additional battery pack that has been attached to the 2200XL? The 51minutes runtime is a number consistent with the load we have placed on a stock standalone 2200XL. With the extra large battery pack we've added, the runtime should be more than 2.5 hours. * I see the "Bizzare configuration" graphic on the

We recently had to replace an old APC SmartUPS 3000 with a newer 3000VA (the 2U one). It has both serial and USB in the back (with an RJ-45 on the end of the serial cable). I can't get the apcsmart driver to connect. I figured it should work the exact same as the old UPS, with /dev/ttyS0 as the port (I'm using the same port on the server that the last one was plugged into). I even

Hello... I have dovecot 1.0.10 running with users in an LDAP database. Things are working as they should with IMAP. However, I can't seem to make deliver w. postfix work they way I want. My problems are: Mail to users who do not exist in LDAP or locally are accepted and mailfolders are created. I want mail to users that do not exist in LDAP or locally to be rejected. Mail is delivered

I'm trying to use a rackmount Smart-UPS from APC with the USB connector, and I'm running into some issues. They seem to stem from the fact that the Report Descriptor is much larger than any other UPS I've seen (61939 bytes). Here is the quick fix that I put in libusb.c after getting the HID descriptor, and before getting the Report descriptor, which seems to work okay:

Hi. Could anyone please provide info on how nut makes ups restart after power is back? I've configured nut to communicate with APC SmartUPS 750 via 'newhidups' driver and this works w/o probs in case of shutting the system down. The UPS would stay on though. After the power returns, I'd expect UPS to restart so that servers would start either. This would never happen, and I have to

Hello. I've been running a two machine setup with a mge-shut for some time without problems, and now I'm configuring a three machine setup with an APC Smart 1500. The UPS has three machines connected to it, in a peculiar way: one windows machine is connected via USB. The second windows machine is using an agent to monitor messages from the first windows machine. Then, I have a GNU/Linux

Well, after our first real extended power outage, I found out that even though the UPS 1000 RM is recognized okay, it does not work properly. It never seems to see any change in UPS status. It looks very similar to the other issue I reported with the APC CyberFort 350. I never was able to get to the bottom of the CyberFort issue, but I'll bet it's the same issue as we have with the

Hello! I am tracking the Development tree and I am trying to capture the output from newhidups, as such: [root]# newhidups -u root -DD -x generic -x vendorid=0001 auto > UPSdump.txt If I don't redirect the output to the .txt file, everything is printed on the screen. If I add the redirect, the output is again printed on the screen; the .txt file however only contains the first

I know this isn't exactly the right place to ask, but I figure at least *someone* on this list has done it once. I recently acquired an AP9617 web/snmp management board for my UPS. The web and telnet part of it work great. However, I can't get *anything* from the snmp interface. I've triple-checked the community name and access settings (currently are wide open). I've ensured

The (2.2.1) upshid-ups driver reports battery.temperature rather than ups.temperature. Here's a quick patch to have it show up in the status page... --- clients/upsstats.c.DIST 2008-03-04 09:15:40.000000000 +0000 +++ clients/upsstats.c 2008-03-04 09:16:20.000000000 +0000 @@ -787,6 +787,11 @@ return 1; } + if (!strcmp(cmd, "BATTTEMP")) { +

Hi, I was wondering if there was any support in NUT for networked APC UPS's. All the configuration examples I see in the documentation are for USB/Serial connections to the UPS. I could mess around with serial/USB cables, but I'd really rather talk to the UPS over the network. I don't want all my servers relying on a single machine with a serial connection. -matthew

Hi, I was wondering if there was any support in NUT for networked APC UPS's. All the configuration examples I see in the documentation are for USB/Serial connections to the UPS. I could mess around with serial/USB cables, but I'd really rather talk to the UPS over the network. I don't want all my servers relying on a single machine with a serial connection. -matthew

Folks, while I've got the above combination to compile and run under Solaris 10, it seems that there are still problems in the libusb/ugen driver stack from Sun and or the APC Smart UPS 1500, so things aren't actually working. It seems that the APC Smart UPS 1500RM doesn't return the HID descriptor length information in 0x21 as noted in a previous thread, but in my case, it also

Greetings: I've been following through the instructions on how to connect an APC BackUPS 650 ES to USB, and have it monitored with NUT... I know my system can SEE the UPS, as DMESG shows this: hiddev96: USB HID v1.10 Device [APC Back-UPS ES 650 FW:818.w1.D USB FW:w1] on usb-0000:00:04.2-1 usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver I can see

Network UPS Tools version 2.0.5 has been released. http://www.networkupstools.org/ Direct access: - Download: http://www.networkupstools.org/source/2.0/nut-2.0.5.tar.gz - News: http://www.networkupstools.org/source/2.0/new-2.0.5.txt - ChangeLog: http://www.networkupstools.org/source/2.0/ChangeLog

Network UPS Tools version 2.0.5 has been released. http://www.networkupstools.org/ Direct access: - Download: http://www.networkupstools.org/source/2.0/nut-2.0.5.tar.gz - News: http://www.networkupstools.org/source/2.0/new-2.0.5.txt - ChangeLog: http://www.networkupstools.org/source/2.0/ChangeLog

Shamelessly reusing the announcement Arnaud sent about three months ago for nut-2.2.1: "We're preparing to release 2.2.1-pre2, so if you have some fixes to backport on Testing, consider announcing it and doing asap. As always, compatibilities update and bugfixes only!" Regards, Arjen -- Eindhoven - The Netherlands Key fingerprint - 66 4E 03 2C 9D B5 CB 9B 7A FE 7E C1

Hello.... I'm testing the functionality of my NUT-setup (NUT 2.0.4-4 - Debian stable). The system is connected to the UPS, but is not powered by it. When running "upsmon -c fsd", upsmon says "Auto logout and shutdown proceeding". This is all well and good, but I never see the machine waiting for the UPS to cut the power. Instead it shuts down. It's my

Dear all, The background is that I'm trying to fix this bug in the geometry package: https://r-forge.r-project.org/tracker/index.php?func=detail&aid=1993&group_id=1149&atid=4552 Boiled down, the problem is that there exists at least one matrix X for which det(X) != 0 and for which solve(X) fails giving the error "system is computationally singular: reciprocal condition