similar to: Tripplite Smart1500

Hello, I have a TrippLite SMART1500RMXL2U that I'm trying to get running with Nut 2.2.1. Running upsdrvctl start works, upsd works, but upsc has "issues": je-nas:~/src/nut-2.2.1# upsdrvctl start Network UPS Tools - UPS driver controller 2.2.1- Network UPS Tools - Tripp Lite OMNIVS and SMARTPRO driver 0.11 (2.2.1-) Warning: This is an experimental driver. Some features may not

Hello, I have a Tripplite SMART1500 UPS, and I'm having a little luck with the tripplite_usb driver. Only a LITTLE though. It's working better than any of the other drivers I've tried, but I'm not getting a status from it. Here's the output of upsc: battery.voltage: 0.00 battery.voltage.nominal: 36 driver.name: tripplite_usb driver.parameter.port: /dev/hiddev0

Please ignore the previous message as I sent it before it was complete. Hello, I have a Tripplite SMART2200VS that isn't being shut down when the nut master asks it to. My initial test was simply upsmon -c fsd which did cause the system to shut down, however the UPS remained on and providing power to its loads. Looking in the logs (daemon and syslog) it was not clear to me that NUT was

OpenBSD 6.1/amd64 nut-2.7.4p0 (from OpenBSD package) UPS: Tripp-Lite OMNI1500LCDT I cannot get the driver for the UPS to load without error. Here are the commands, with the output, and the config files: ======================================================= # upsdrvctl start Network UPS Tools - UPS driver controller 2.7.4 Network UPS Tools - Generic HID driver 0.41 (2.7.4) USB communication

Hello, Does anyone know the settings to get this UPS talking to nut? I'm trying to get it working over the serial port, and I've tried using genericups type 5. When I do this, the driver seems to initialize, but then upsc shows the status to be OB LB. When I unplugged the UPS, there was no change in the status. I noticed on the Tripp Lite web site that this uses a different cable. It is

<nut-upsuser at lists.alioth.debian.org> I am doing my best to avoid have to spend $280 for a network monitoring card to put into a $190 UPS just to have some good remote monitoring capabilities. Rather, I would like to monitor my many 1U Tripp Lite's on my network using a Raspberry Pi running Raspian and using NUT. However, I cannot seem to get it working. And I while the hardware

I'm working on a gentoo server with Nut 2.0.5-r1 and libusb-0.1.12. I originally tried the hidups driver which seemed to work, but produced a large amount of unhandled events. Then I tried the newhidups which told me my ups wasn't supported. When I try using tripplite_usb -u root -DDDD /proc/bus/usb/002/002 I get that there isn't a match. But when I try using tripplite_usb -DDDD

Hello to all, I have a Tripplite SMART1500RMXL2U and nut-2.4.3 running on CentOS 5.5. To test the shutdown, I issued the command upsmon -c fsd but it was unable to turn off the ups. I got the following message: libusb_get_interrupt() returned 0 instead of 8 while sending 3a 47 b8 0d 00 00 00'. G......' (repeated many times) Could not turn off UPS (is it still on battery?) At this

I have a Tripp Lite SMART1500 RMXL2U UPS and I'd love to be able to access it via USB. I found that the latest NUT sources in CVS has a driver that looks like it might work. Any chance that driver would work the my UPS? I tried running it and it's not working: failed to detach kernel driver from USB device... trying again to claim USB device... failed to claim USB device, trying 1

Hey Charles, Many months ago you assisted me in making some code changes to get my Tripp Lite up and running. Thank you for that. Those changes you committed to the repository work very well. I just built a new image for a Raspberry Pi running the latest Raspbian OS and the latest nut-master. I have everything working ... except I seem to be losing my device periodically. So if I enable my

> > > 2.117586 send_cmd(msg_len=2, type='G') > > 3.219418 libusb_get_interrupt: Connection timed out > > 3.219474 libusb_get_interrupt() returned 0 instead of 8 while > sending 3a 47 b8 0d 00 00 00 00 '.G......' > > 4.219593 libusb_get_interrupt: Connection timed out > > 4.219661 libusb_get_interrupt() returned

On May 12, 2017, at 10:06 AM, Mike <the.lists at mgm51.com> wrote: > > > OpenBSD 6.1/amd64 > nut-2.7.4p0 (from OpenBSD package) > UPS: Tripp-Lite OMNI1500LCDT > > I cannot get the driver for the UPS to load without error. > > Here are the commands, with the output, and the config files: > > ======================================================= > #

Hello, I have a Tripplite SMART2200VS that isn't being shut down when the nut master asks it to. My initial test was simply upsmon -c fsd which caused the system to shut down, but the UPS remained on and providing power to its loads. Looking in the logs (daemon and syslog) it was not clear to me that NUT was telling the UPS to shut down (I was expecting to see "Shutting down the UPS

Hello Charles, I think we are making progress! I grabbed nut using git, and applied your patch without any problems. Getting to the point that I could run a configure on my RPi - was something else. I found this blog post, which was very helpful (for anyone else that may try it): http://atelier-orchard.blogspot.com/2013/11/raspberry-pixf86-video-fbdev.html It's not in English, but you get

My UPS is connected to a Raspberry Pi by USB. After a few hours of working, the service fails. Looking at kernel messages I noticed that the device is repeatedly disconnecting and reconnecting. I have tried using a different USB port and using a brand new USB cable. I have not had success by changing config parameters like pollfreq/pollinterval/etc. What is causing the UPS to keep disconnecting?

Hello Charles, Thanks for the feedback. I will try to answer some of these questions: > 09AE/0001 is essentially a USB-to-serial converter, and is not > compatible with usbhid-ups. (Theoretically, we could have a companion > driver that talks the same protocols over a real RS-232 port, but the > hardware I used to develop the tripplite_usb driver only has a USB > port.) Ah, that

On 5/13/2017 10:20 AM, Charles Lepple wrote: > On May 12, 2017, at 10:06 AM, Mike <the.lists at mgm51.com> wrote: >> >> >> OpenBSD 6.1/amd64 >> nut-2.7.4p0 (from OpenBSD package) >> UPS: Tripp-Lite OMNI1500LCDT >> >> I cannot get the driver for the UPS to load without error. >> >> Here are the commands, with the output, and the config

I see the link here <https://alioth-lists.debian.net/cgi-bin/mailman/listinfo/nut-upsuser>, but clicking it results in a 404. Before I waste everyone's time posting my question, I really wanted to search to see if it's been solved already. -------------- next part -------------- An HTML attachment was scrubbed... URL:

Charles, It starts out good, then goes into a Connection timed out loop. If I can provide any information to fix a driver I'll do my best. Here's the output: # /usr/local/ups/bin/usbhid-ups -DD -a eaton Network UPS Tools - Generic HID driver 0.41 (2.7.4) USB communication driver 0.33 0.000000 debug level is '2' 0.002550 upsdrv_initups... 0.288229 Checking device

I have several Tripplite SU2200RMXL2U and SU3000RM2U units that I would like to monitor using Nut. I have tried to attach to the units using a serial cable with the tripplite and tripplitesu drivers with no success. The drivers simply seem to not recognize the UPS. I then tried using the tripplite_usb driver with the usb cable. It definitely sees the UPS but I am getting errors which told me