similar to: ups.delay.shutdown clarification

A client of mine has an APC Back-UPS 350 model (USB connected). His office had a power incident yesterday, where there was an interruption of about 30 seconds. During that time, the server shut down. As soon as it went on battery, the daemon initiated a shutdown. In checking it today, I see the ups.delay.shutdown setting is -1. I tried to adjust it, but could not do so. What does the

Following the recent "trans2" exploit announcement, SuSE released kernel 2.6.5-7.111.5 to deal with it. I've installed the kernel upgrade on my desktop (SuSE 9.1, Samba 3.0.4). However, with this kernel, when I try to save to a share on my server (Samba 2.2.8), I get this set of error messages: Dec 13 22:10:25 p133 kernel: smb_trans2: invalid data, disp=0, cnt=0, tot=0, ofs=0 Dec 13

Hello list! I can't seem to get this running via RS232 monitoring; I've been told that NUT won't support serial connections, and find this hard to verify. Does anyone else have this running on the SU10KRT3U via RS232? If so, what driver did you use? I'm getting no satisfaction from the "tripplite" driver; upon upsdrvctl start, I get "Failed to find UPS - giving

Hello all, I was having this problem and finally found a temp fix for it. The symptoms seem to be this: --> You are on a linux client --> You have mounted a samba drive from you linux client to a linux server. --> When you try to make modifications or copy file from your client to the server, it takes a long time or times-out. --> Your /var/log/mesages file states smb_trans2:

How do i upgrade my Xen guest (domu1) ? On a stand alone hardware one would insert DVD/CD/Network and perform the upgrade, What is the equivalent in Xen World ? Tahnks !!! -- Regards, mantra - Instrument of Thought _______________________________________________ Xen-users mailing list Xen-users@lists.xensource.com http://lists.xensource.com/xen-users

I had a brief power interruption this evening which caused a spurious shutdown. The system log contains a report of "low battery" status; however, checking the battery soon after powering up again showed a fairly typical 80% charge. The UPS had, however, been beeping to indicate imminent shutdown, which is slightly suspicious. Previous power interruptions have been fine but either they

Is it possible to shutdown earlier by certain conditions: by battery level and estimated by UPS runtime. In APCUPSD this done by config options "BATTERYLEVEL" "MINUTES". By what condition NUT shutdown server? How to disable UPS shutdown?

Hi guys, what distribution do you recommend, if you want to run producive systems on it. i got a cluster with two sles10sp2 nodes - but i''m not that satisfied. The migration of my windows-systems are not working in an acceptable way and the pv-drivers for win of suse are not a speed boost at all. Well I could spend big money for Xen Enterprise or VirtualIron - but - do I really have to

I run a small network at home, with a Linux server, which shares files and a printer. I also have a Linux PC (RH 9, KDE 3.1, CUPS 1.1.17) from which I am trying to share a Lexmark 3200 inkjet. Samba (2.2.7a-security-rollup-fix) seems to be generally configured OK - I can print to the Lexmark from a Windows 98 system, and from another PC running Mandrake 9.1. However, I am unable to print from two

My Belking is no longer responding to the megatec driver. I get * Starting UPS drivers ... Network UPS Tools - UPS driver controller 2.0.5 Network UPS Tools - Megatec protocol driver 1.5 (2.0.5) Carlos Rodrigues (c) 2003-2006 Megatec protocol UPS not detected. Driver failed to start (exit status=1) * Failed to start UPS drivers! Thank you, Barbara Smith -- Using Opera's

is 3110us supported now?

Hi, I am trying to install xen-3.2.0 , but its failing. The rpms used for installing are 1. xen-3.2.0-0xs.fc8.i386.rpm 2. xen-3.2.0-0xs.fc8.src.rpm 3. xen-debuginfo-3.2.0-0xs.fc8.i386.rpm 4. xen-devel-3.2.0-0xs.fc8.i386.rpm 5. xen-libs-3.2.0-0xs.fc8.i386 when I tried installilng the first rpm rpm -ivh /home/devi/Desktop/xen-3.2.0-0xs.fc8.i386.rpm it gave an failed dependencies

Greetings; I have the newest nut (nut-2.2.2-4.fc10.i386) from fedora 10 repos) installed and this ups (from lsusb -vv): Bus 001 Device 006: ID 050d:0751 Belkin Components Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 1.10 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0

Hi, In Red Hat /etc/init.d/halt script, it expects upsdrvctl to be in /sbin rather than /bin which sounds normal considering the power of that command. If I move this file to sbin, this is what I get when invoking it: [root@serveur1.sassine.eu nut-2.0.5]# mv /bin/upsdrvctl /sbin/ [root@serveur1.sassine.eu nut-2.0.5]# which upsdrvctl /sbin/upsdrvctl [root@serveur1.sassine.eu nut-2.0.5]#

I just purchased a new ups and I'm unsure about several things. For one thing I don't know what driver I need. Also, it uses a usb port and I had a serial port before. I'm not sure how this needs to be set up. Thanks in advance for help Barbara -- Using Opera's revolutionary e-mail client: http://www.opera.com/m2/

hi i think nut close the computer when the battery is low... is there a way to close it after a few time is electricity is off? thanks

On 07/14/10 11:27, Arjen de Korte wrote: > the UPS should power off(and restart when the power comes back Can I set any UPS to only provide power after the battery is charged to a certain level? Or better yet, a certain length on consecutive time when the power has been on. I'd be worried about flapping, where the power goes on and off.

I would have to buy a new UPS that have to function for a simple desktop PC. I would the best about NUT compatibilty. The class of UPS must be 600-800 VA. What do you recommend me? Best regards Hello to all. -- Email.it, the professional e-mail, gratis per te: http://www.email.it/f Sponsor: Natsabe.it la più grande erboristeria online italiana * prezzi bassi tutto l'anno !

I just installed nut in Debian and all of my files are missing. I'm not even sure what all files are required. I hope someone can give me the list of the files and I can create them. Also if there is any pertinent info I need. Thanks

You''ll have to forgive me ... I''ve been toying with rails for about a week and although I don''t feel completely lost there''s still a lot that I don''t understand. Here goes. Assume I have a controller called admin in app/controllers as well as three model classes in app/models: product, category, warehouse. How exactly do I use the admin controller to