similar to: [1.6.2.9] Echo even when using headset?

Hi, we are looking to roll out PBX IN A Flash at our office. The first group will be using Soft Phones (X-Lite appears to be the best and works in Windows, Apple & Linux). There are many types of USB Headsets to choose from and a fairly broad price range. Is there any USB headsets people would recommend? I'm specifically interested in acceptable audio (speaker and microphone) quality

Hi, You need to have completely replaced the Microsoft driver, because it doesn't support the headset or ctp Bluetooth profiles. This gave me fits! I followed the instructions at http://www.windowsdevcenter.com/pub/a/windows/2005/07/05/bluetooth.html and it works with both a Plantronics and a Motorola Headset, and I can answer calls with idefisk, eyebeam, x-lite, and kapanga. If you end

I am able to pickup, hangup, and flash, using the buttons on the phone with all of the soft clients and both of the headsets I mentioned below. I don't believe I had to change anything on the client side, just had to get the ctp (cordless telephone profile) working in the bluetooth stack, which was a pita. I struggled with the same issue...I could use the headset, but that's not very handy

Afternoon, I recently upgraded a machine to CentOS 4.0 and it has two sound cards: built-in VIA, Cmedia PCI card. The OS recognizes both and I can use the tool, system-config-soundcard to test them. However, I can't seem to get any sound out of the VIA card, but the Cmedia plays the test sound just fine. The problem is that I can't get any sound apps to use the Cmedia card,

Hi *, is anybody using a bluetooth headset with some success?? If yes, which stuff is used (usb dongle and BT headset)? (I would like to : 1. be able to receive calls, if possible to answer acalls with the headset. 2. be able to place call, but this seem lot more difficult.) Laurent

I would like to be able to host music not by myself for free. The only problem is, I can't find a place that will do it. When I want to share a song with a forum, I am currently forced to use RapidShare, MegaUpload, or UploadingIt, all of which causes problems for somebody. I would like to be able to host a song, have a link to click on it, and it doesn't have to be downloaded and cause

Hello I'm sure someone has already tried this: I use a couple of electric heaters to heat my office. I'd like to somehow connect them to Asterisk so that I could switch them on remotely by either calling the IVR or sending an e-mail to the Asterisk host, so that the room is warm when I get to the office :-) Any information appreciated. Thank you.

Hello, I'd like to run Asterisk on an embedded device, where space is scarce. It should be able to handle calls from a VoIP provider in SIP, calls from the PSTN through Dahdi, and voicemail. If someone's already done this, I'd like to know which directories/files are required for a basic install? Does this look right? ================= /bin/asterisk /etc/asterisk/ asterisk.conf

Hello I need to find a recent and neutral comparison of the major products available to connect an Asterisk server to the telephone network, whether ISDN (BRI) or PSTN, and through a PCI card or some external box. I'm told there are less issues (echo, stability) with external boxes compared to PCI cards. Apparently, the main brands are Digium, Sangoma, Rhino Equipment, Patton, and

Hello For users who 1) don't have a QoS-capable ADSL router and 2) would like to run Asterisk with a couple of SIP trunks, I was wondering what hardware is recommend to run any of the main open-source *WRT projects to which Asterisk has been ported: (http://en.wikipedia.org/wiki/List_of_wireless_router_firmware_projects Thank you.

hi list. after my unsuccessfull experiences with mISDN i tried again to implement a zaphfc based solution. problem is: sound on calls via capi is stuttering/broken and therefore unuseable. my conf: - cel 1300, 256mb ram - avm b1 via capi connected to my outgoing ISDN - acer surf pci via zaphafc and crosslink cable with termination as internal bus - siemens gigaset 3035 as internal phone -

Hello I read a whole book on OpenVPN, but still can't figure how to configure the server + client so that the the client connects and sends SIP/RTP data through the tunnel. To get started, I'd rather use a shared key instead of X509 (certificates + keys). The server is running on a uClinux appliance, with /dev/net/tun, and OpenVPN is 2.0.9. The clients will be Windows hosts connecting

Hello I'm trying to use ChanIsAvail() to check when the landline is back to idle after a call, but for some reason, Asterisk doesn't detect that the callee has hung up after listening to MoH for a few seconds: ========== extensions.conf ;Play MoH for a few seconds, hang up, and ;check ChanIsAvail() able to detect when line idle again exten => 8888,1,Answer() exten =>

Hi, What USB headset would you recomend? We have some laptop soundcards that are really bad and I would be glad if you could share your experiences when changing to a USB headset instead of using the built in soundcard in your computer. Thanks! Regards, Jan

Hi Everyone, I can connect the Jabra GN2124 + GN2100 (smart cord) to the Aastra 53i receiver port and I get a tone. But when I connect it to the headset port there is no tone. I am running firmware 2.4 and I can't seem to find that DHSG, EHS or whatever the setting maybe called to enable to get this headset work with the phone. Can anyone quickly tell me where the audio options are on this

Guys. Im writing this because Ive checked the wiki, Xten website and read a lot of docs and still cant figure out a way around the NAT issues. Maybe somebody else can give me some ideas from a fresh perpective. My test setup is this: Asterisk -> 2wire homeportal Firewall -> internet Computer with Xten eyebeam The asterisk box and the computer with xten beam are behind the same

Hello I'd like to display CID information on users' monitor running Windows. I know I can run a script through the dialplan to send a datagram that is picked up Impulse Technology's free NetCID (www.imptec.com), but I'd rather use an open-source solution. An alternative would be to use a Windows application that would connect to Asterisk's AMI. I don't know if multiple

-----Original Message----- From: Ferguson, Michael Sent: Tuesday, February 01, 2005 11:35 AM To: 'asterisk-users@lists.digium.com' Subject: Messaging with * and eyeBeam G'Day All, Eyebeam has gotten my interest but I do not have a "high-altitude" view of its interraction with *, therefore my questions. I called xTEN but they preferr to talk to telcos and ISP's

In an attempt to eliminate audio echo I upgraded one side of a working x-lite to x-lite connection to eyebeam. No joy, and what was worse is the audio was even worse now - just noise. Ok, I upgraded the other side to eyebeam and same thing. I'm not even using video (will enable it in sip.conf later, one change at a time). The connection looks something like: eyebeam client

hi, hs anyone able to make video to work on asterisk? i tried following this: http://www.voip-info.org/tiki-index.php?page=Asterisk+phone+xten+eyeBeam i can see that eyebeam is trying to broadcast a video but the other eyebeam is not receiving it. i tested the same setup but this time using ser with rtpproxy and eyebeam video works fine. any ideas? where do you think should i start