similar to: UK BT ISDN30 settings?

Has anyone got a working zaptel.conf and zapata.conf for a Digium Wildcard TE110P T1/E1 Card. It's connected to a BT ISDN PRI (EuroISDN) with 24 channels. Inbound works fine, but outbound isn't setting CLI (it seems the line supports 6 digit CLI). Inbound CLI works fine. In the dial-plan using Set(CALLERID(num)=123456) then Dial(Zap/g1/01234567||frT) Where 123456 is in the range of BT

Hi, I am running Asterisk v1.2.7.1 with a Digium TE110P. My dialplan is very simple, when a call comes in on my analogue BT PSTN line, it rings the other ZAP interface (my house phone). Slightly pointless (having a 1x1 switch) I know, but I am planning on doing more with internal SIP extensions, and outgoing SIP services etc.... At the moment it's just simple though whilst I try to fix this

anybody recommend a supplier in the UK for a pri/isdn30 line (other than BT) thanx very much __________________________________________________ Do You Yahoo!? Tired of spam? Yahoo! Mail has the best spam protection around http://mail.yahoo.com

Dear All, Thank you for taking the time to read this post - I am *confused!* as to why my asterisk setup does not work as it should. I have an ISDN 30 connection for telephony, a Sangoma card, and asterisk installed. Incoming calls, and outgoing calls work 100%. Making an international call, results in silence, or the error message all circuits are busy Numbers being passed to the trunk for

>> So it sounds like it should "just work". I'll let you know in a few >> weeks time :) > TDM400P to E1/T1 card faxing fails by design. The lack of > synchronisation between cards means it can *never* work with any > reliability. The hardware will not permit it. >> >> (And I know I've asked this before, but any recommendations for a >>

A client used to use BT isdn30 and ported the numbers to telewest several years ago. Now, the client moved to adept telecom. I *think* adept resells BT products. We got new numbers from adept (bt?) and the old pbx on the telewest lines forwards the calls to the new numbers. On the adept line I got a digium card in an opteron supermicro server. ztcfg gives me over 99.99 pretty much all the time.

We will be connecting our Asterisk server to ISDN 30 and intend using the Sangoma A101 card. The install location is in London (UK). Sangoma card at Voipon http://www.voipon.co.uk/sangoma-a101-pri-isdn-card-p-132.html?gclid=CI32vJz22I0CFQXklAodIgjHaA I would be grateful to hear if this is the right choice of card. Usage reports would be helpful. Regards Rory -- Rory Campbell-Lange

Greetings to one and all on this fine list; We have the current system: Meridian 1 Option 11 +-------------------+ | | ISDN/30 (DASS/2) ===> |NTAK79BB (2MB Pri) | | |<-->4x16 port Digital / 1x16 port Analogue ISDN/30 (EUROIDSN) ===> |NTBK50AA (2MB Pri)

Ok Guys, I've done a tonne of hunting around on this problem, but can't find much help. I'm running: asterisk 1.4.19.1 libpri 1.4.3 and zaptel 1.4.9.2 which I believe has been modified by RedFone to add the ztd-ethmf module. My interface is a RedFone foneBridge2 4 Span; and I'm connecting to a BT E1 PRI / ISDN30e with 15 lines on span 1, and a legacy Panasonic PBX on span 4. Upon

Hello, I am trying to get a Wildcard TE110P to work in a relatively modern HP Proliant DL385p Gen8 server. Being a potent 12 core Opteron server I expected no problems. Much to my dismay the dahdi_test results are constantly terrible: # dahdi_test Opened pseudo dahdi interface, measuring accuracy... 89.101% 89.195% 89.142% 88.957% 88.953% 89.115% 89.089% 89.134% 89.066% 89.021% 88.933% 89.044%

Hi, I've just been made aware of Asterisk through the article on Slashdot. We're a small UK company with a ISDN-30 link to the office and a Meridian (Nortel) PBX. We're expanding and moving offices soon and I'm looking seriously at VoIP technologies. So starter for ten, can Asterisk interface in with ISDN-30 technology? I'm assuming the set-up is a server sat running

Hi :) My employer is looking to move a call centre to a new office, and has been increasingly frustrated with their legacy PBX (call-logging licensing and hardware upgrade costs). So I've stepped forth as the Open Source Pedant and suggested Asterisk so we can do all our own CallerID / call logging / analyses, and make use of IP Phones / teleworking, etc. The problem begins in that I only

Quoth Jon Morgan <jon.morgan at motors.co.uk> > >We have a 2 port Digium TE220P card, one span is configured to connect to our ISDN30 provider (British Telecom), the other span connects to our internal PBX. Here's the zaptel.conf snip: > >span=1,1,0,ccs,hdb3,crc4 >bchan=1-15 >dchan=16 >bchan=17-31 > >span=2,0,0,ccs,hdb3,crc4 >bchan=32-46 >dchan=47

Thanks to help on this list and Sangoma's support we have incoming and outgoing calls passing through asterisk. However both incoming and outgoing calls are greeted by silence. I've noted our existing config below with our test extensions.conf. Help much appreciated Rory Zaptel ----------------------------------------------------------------------- loadzone=uk defaultzone=uk #Sangoma

Have anyone tried to interface BT's Broadband Voice with asterisk? Kannaiyan

Hi all I'm using sangoma a200 cards in the UK and have the ongoing, often noted problem of disconnect supervision with BT POTS lines. Just noticed this post on http://www.voip-info.org/wiki/view/UK+Asterisk+Details stating that potentially someone's got a solution : "TDM400P &amp; Not Detecting Hangups: Got a TDM400P installed and having problems with Asterisk not detecting

If anyone can help me with this I'll be soooo grateful :) We have a isdn30 line, with a DDI range. We also have 2 business units that have separate 0870 numbers that are mapped onto 2 DDI numbers. I would like to be able to present these 0870 numbers from the business units so that the correct number is displayed on a callerid, or when 1471 is dialled. BT claim that I can only have a

Hi I am having problems getting my card to hang up properly when a remote party hangs up the line. I know i have to use the busydetect stuff but it doesn't seem to be working. It is a BT line and my zapata.conf is as follows: [channels] language=en rxgain=0.0 txgain=0.0 immediate=no echocancel=yes echocancelwhenbridged=yes echotraining=yes signalling=fxo_ks context = dialphone channel =>

Hi Just moved offices in the UK and moved our Asterisk box from old one to new one. Using idefisk softphones, Junghanns quadbri card for ISDN 2e interfaces. At both offices we had one standard number and a DDI range, routed with Asterisk. We'd set up the configuration so each idefisk set its own caller ID which then got sent by the extensions.conf script. Worked fine at old place but in

I'm considering purchasing a Digium TDM400 card with FXO module to connect my asterisk box up to BT's PSTN. I've searched Google and have found that in the past there have been problems with this card detecting the calling party hangup. I am interested to know if this issue has now been resolved and if UK caller ID is now fully supported. Also if anybody using the card in the UK is