similar to: DAHDI Error

Hello, I am missing any description of zaptel/DAHDI alarms. The TE200 series user manual contains only a description of LEDs states. These alarms states are visible in zttool/dahditool or in astersick CLI (zap show status) and I wonder what is the real meaning of these alarms for E1 channel. Possible alarm states (based on zaptel.h 1.2): 1. No alarms 2. Recovering from alarm 3. In loopback

Hi, After an upgrade, I discovered yesterday strange things I would like to share here. Basically, I'me comparing platforms: The first one is a 2.6.26 (Debian Lenny) platform, with Asterisk 1.6.1.18, Libpri 1.4.10.2, Dahdi revision 8853 (must be between 2.3 and 2.5, I think). The second one is a 2.6.32 (Debian Squeeze) platform, with Asterisk 10.5.1, Libpri 1.4.12, Dahdi 2.6.1. Both are

Hello everyone. I have server with 2E1 PCI card, asterisk 1.4.35, dahdi 2.4.0, libpri 1.4.12-beta2. One PRI trunk looks to PSTN and take a clocksource from telco. Another trunk looks to PBX with DECT system. Some outgoing calls from asterisk to PSTN drops. The last message that exists before hanging up process is: DEBUG[28467] channel.c: Got a FRAME_CONTROL (8) frame on channel DAHDI/... This

Dear all, i have a problem with a system running - Ubuntu 10.04 ( all updates done ) - ii asterisk 1:1.8.5.0-1digium1~lucid Open Source Private Branch Exchange (PBX) - ii asterisk-dahdi 1:1.8.5.0-1digium1~lucid DAHDI devices support for the Asterisk PBX I also use freepbx 2.9 for the configuration. Hardware is a Dell R410 and a Digium

We need to monitorate the E1 with nagios, somebody did this? any ideia? Thanks in advance! -- Atenciosamente, ------------------------------------------------------- Dario Quiroz (71) 9275-9080 gtalk: darioquiroz at gmail.com ------------------------------------------------------- -------------- next part -------------- An HTML attachment was

Hello I am trying to configure TE420P but i am confused what to give chan_dahdi :( Below is configuration i am using for TDM400P Please help what changes to make in it... Please provide a link as well [trunkgroups] [channels] ;default for channels switchtype=national rxwink=300 hidecallerid=no callwaiting=yes usecallingpres=yes callwaitingcallerid=yes threewaycalling=yes transfer=yes

Hi All, This posting regarding PRI voice optimization, on dahdi 2.1.0.4. we have more than 4 machine running on 4 port PRI card with echo cancellation hardware based. i have enabled echo cancel from chan_dahdi.conf using echocancel=yes, now more than 70% of call get good voice but some of calls having issue for callquality and other voice related issues. now my question is that is there any

Hello, We are having issues with a NEW Sangoma A108D: -- Executing [691918892 at pbx1:1] Dial("SIP/xtravoip200-009d24b0", "DAHDI/g0/691918892|30|m") in new stack [Oct 1 10:04:43] WARNING[14171]: channel.c:3170 ast_request: No translator path exists for channel type DAHDI (native 76) to 256 [Oct 1 10:04:43] WARNING[14171]: app_dial.c:1237 dial_exec_full: Unable to create

Hi All, I have a TE121P card installed and since connected it to the PRI I keep getting the Current Alarm as continually changing from Blue Alarm/Recovering and Recovering. The config I have is: /etc/dahdi/system.conf bchan=1-15,17-31 dchan=16 echocanceller=mg2,1-15,17-31 loadzone = cn defaultzone = cn /etc/asterisk/chan_dahdi.cfg [channels] Context=telco

hi,all i have just set up asterisk 1.6.0.7 rc1 with spandsp 0.0.5 pre4 to ReceiveFAX, link to a E1 (DE410P) using dahdi this can receive the fax from E1 successfully, but i see many error message in the log like this: [Mar 16 09:24:38] ERROR[23540] channel.c: ast_read() called with no recorded file descriptor. when i receive a 5 pages fax, i will see this error message over 200 lines..... it

Hello! I am trying to configure my digium TE220 dual-span pci express card with Dahdi. I seemed to have managed to set up the card with the Dahdi kernel, as demonstrated by executing dahdi_scan: [1] active=yes alarms=RED description=T2XXP (PCI) Card 0 Span 1 name=TE2/0/1 manufacturer=Digium devicetype=Wildcard TE220 (4th Gen) location=Board ID Switch 0 basechan=1 totchans=31 irq=16

Hello- After configuring DAHDI and starting asterisk, I get the following message continuously on the Asterisk console: WARNING[2057]: chan_dahdi.c:4158 pri_find_dchan: No D-channels available! Using Primary channel 16 as D-channel anyway! My card is a D410P configured for E1, only the first span is configured, and configuration snippets are as follows: From /etc/dahdi/system.conf:

I am running Asterisk 1.6.1.6 and DAHDI/DAHDI tools 2.2.0.2 compiled from source on a Debian Lenny box, also running FreePBX 2.5.2. I also have an OpenVOX TDM400 card installed with an FXO port on port 1, and an FXS port on port 2. I have a POTS line installed and working on the FXO port. However I've encountered a weird problem that I can't seem to figure out. I have incoming POTS

Dear All, How can we know the On board supports echo cancellation I have *Digium, Inc. Wildcard TE410P quad-span T1/E1/J1 card 3.3V (rev 02)*board all working fine but sometimes i got echo when user are calling a PRI. is there any way to know on board echo cancellation . regards Dhaval -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi list! We currently have a PRI gateway composed by a box with two Digium quad-span PRI cards (a TE420 and a ). One of the cards is filled with TELCO1, while the other has first two slots filled with TELCO2, and 3rd slot with TELCO3. I am currently having (timer ?) issues on TELCO3 (span 7) D-Chan (202 as determined by dahdi_genconf ) is constantly failing causing on-going calls to terminate.

Hello all, I have the following working (somewhat) setup: TELCO | | E1 (30 Chan -- TE210 SPAN 2) | | Asterisk box 1.6 with DAHDI drivers loaded Digium TE210p | | E1 (30 Chan -- TE210 SPAN 1) | | NEC PBX

Hello, I'm having issues connecting throu PRI with the following error "Requested transfer capability: 0x00 - SPEECH" Below are the logs: == Using SIP RTP CoS mark 5 -- Executing [97052660 at voipphones:1] Set("SIP/4856-00000003", "CALLERID(num)=xxxxxxxxx") in new stack -- Executing [97052660 at voipphones:2] Dial("SIP/4856-00000003",

All This is a small issue that I stumbled onto that has to do with the channel numbering on an E1 connection into an Asterisk Zaptel/DAHDI system. As most of us already know an E1 has 32 channels of which 30(1-15 17-31) are B-channels and 1 (16) is a D-Channel. The 32nd channel is not presented in Asterisk Zaptel/DAHDI. There are other configurations but this is the most common. ***

On Thu, Jun 6, 2019 at 12:17 PM Malcolm Davenport <malcolmd at sangoma.com> wrote: > Howdy, > > There's a dahdi-linux-complete-3.1.0-rc1+3.1.0-rc1.tar.gz. > > Try that. > I noticed that was there, but I didn't try it originally because it's obviously a beta version. However, I did download it and try it. It does compile, but doesn't work correctly. For one

HelloI have the following system Asterisk 1.6.1dahdi 2.2.0.2 TE420P card Centos I have noticed that all the four lights are blinking(ie coming red and then off so on)... Previously I also noted that when dahdi drivers are not installed lights blink but one by one in sequence(like in marriage cermonies :P) and after dahdi installation lights get off ... but this time all at same time