similar to: Asterisk 1.8.x Skips DTMF Digits on a First DAHDI Initiated Call

Hello, After installing on Ubuntu 10.04 using the tutorial on http://hmontoliu.blogspot.com/2010/03/installing-asterisk-and-freepbx-on.html I have a running instance of Asterisk. PROBLEM: result of dahdi_cfg: DAHDI Tools Version - 2.2.1 DAHDI Version: 2.2.1 Echo Canceller(s): MG2 Configuration ====================== Channel map: Channel 01: FXS Kewlstart (Default) (Echo Canceler: mg2)

[18884732963 at from-fax-machine:... - your call is hitting the from-fax-machine context - yet your 'fax' exten is in the from-pstn-4 context. See the "[2011-03-17 13:40:29.6] NOTICE[8825] chan_dahdi.c: Fax detected, but no fax extension" line. When Asterisk detects an incoming fax tone - it tries to automagically route the call to the 'fax' extension in the SAME

I am running Asterisk 1.6.2.17.2 with a Openvox A400 card with 2FXO/2FXS modules. I'm trying to set-up things to route analog fax calls from a FXO port to an analog fax machine on a FXS port on the same card. Outgoing faxes work just fine. But incoming faces are routed to the right DAHDI extension, but the call dropped right as the fax machine rings for the first time. The fax machine

Hi, We have a PRI Trunk (physical E1) and we are getting some rather weird and very isolocated problems. On outbound calls to specific numbers, it would seem to me that DTMF from the remote side is affecting the local asterisk system. Basically what happens: - We make a OUTBOUND call via the PSTN (PRI Trunk) to a remote System - Remote Answers, and converse - Remote sends DTMF on their site to

Hi, I have a running asterisk 1.2.1 (bristuffed) with a TDM400 Board. Connected to 1 port is am ordanary Fax Machine. Everything 'seems' to work, however receiving faxes is very unreliable. Sometimes I receive a normal page, without problems. Sometimes half of a page and the rest is scrambled, but most often, I receive nothing and the other site reports a Fax error... The Fax machine

Hello, Has anyone tried the combination of asterisk 1.2.24, zaptel 1.4.5 and HPEC 9.00.003? In particular, with a hardware configuration similar to: Module 0: Installed -- AUTO FXO (FCC mode) Module 1: Installed -- AUTO FXO (FCC mode) Module 2: Installed -- AUTO FXO (FCC mode) Module 3: Not installed Found a Wildcard TDM: Wildcard TDM400P REV I (3 modules) I have two fully independent systems

I'm having a problem receiving incoming faxes and I'm hoping someone here can help me out. My system is a PBX in a Flash with one dahdi card for my incoming analog lines and another dahdi card for my analog devices (fax and modem). My dahdi-channels.conf file looks like: ; Autogenerated by /usr/sbin/dahdi_genconf on Tue Jun 23 14:56:24 2009 ; If you edit this file and execute

Hello group, I am installing Asterisk on a new pc running Ubuntu 12.04.3 Server. ?I have dahdi-complete-2.7.0.1+2.7.0.1, and have tried 2.6.1 and 2.8.0-rc1 and 2.8.0-rc2. ?I am following along in the ASTERISK The Definitive Guide 4th Edition and on page 116 when I issue the command $ sudo /etc/init.d/dahdi start I get the following error: Loading DAHDI hardware modules: ? ?wctdm24xxp: done

I'm a bit confused on how to setup Zaptel.conf and Zapata.conf when there is a TDM400P and a TE410P installed after upgrade. The TDM400P has 2 FXS in position 1 & 2 and 1 FXO in the fourth position. I see boot, WCT4xxP loading first and WCFXS loading second. According to my understanding, given above, the TE410P should be configured first, then the TDM400P. However, I'm not sure

I installed Trixbox and a TDM400P with 2 FXO and 2 FXS ports and am having an annoying issue with the FXO ports. As soon as I plug either one into the phone line it's as though the line is disconnected i.e. get disconnected tone when trying to dial out, line is busy when dialling in. The CLI shows the following: trixbox1*CLI> zap show channel 4 Channel: 4 File Descriptor: 18 Span: 11*

I am having problems getting a Nicherons TDM400P wildcard clone to dial out. Everything appears to be configured correctly, but although I see call progress, it never seems to actually pick up the phone. (The following is a test of 911 emergency, where I substitute 811 [repair service] as the actual number dialed.) *CLI> -- Executing [911 at from-internal:1]

Hi, I'm having problems using a TDM400P Card. I put my SIM card in a Nokia Premicell and connected it to a TDM400P card but when I make calls to the number, it hangs up automatically. The card also can't call out. Any ideas? I've searched the archives without much success. I appreciate all your help. Details: I'm using Asterisk 1.2.17 on Fedora Core release 5 (Bordeaux). On an

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi all! Days ago I bought a OpenVox A400P card with a port FXS and another FXO that I am testing with my Asterisk installation in my house. I'm using Asterisk 1.4.24.1 with DAHDI Linux 2.1.0.4 and DAHDI Tools 2.1.0.2 on Debian GNU/Linux Lenny. I was reading "The future of telephony" and this [1] document looking for information about

Hello all, Ok it is Sunday afternoon and I am going crazy. I have been running in circles so long that I can't think straight. As an example, I sent this message to the wrong address the first try, AAARRRRGGGGGGHHHHH. I have Asterisk 1.6.0.6 and DAHDI Tools Version - 2.1.0.2, DAHDI Version: 2.1.0.4, OpenSuSE 10.3 x86_64, tdm422 at the end of installing dahdi-linux and dahdi-tools I get:

I'm having real problems with my connection to BT, it is a home line, but after a while it sets an alarm and only a restart of asterisk resets it could some one look at the below configs and suggest any changes to make this more reliable Thanks for your help Robb asterisk version 1.6.1.10 dahdi version SVN-trunk-r7445 dahdi_scan active=yes alarms=OK description=Wildcard TDM400P REV I

Hi I have been searching the wiki and mailing lists and I cant see where my config is incorrect. I have a Digium tdm11b (1 fxo + 1 fxs) this is the output of cat /etc/zaptel.conf # Autogenerated by /usr/local/sbin/genzaptelconf -- do not hand edit # Zaptel Configuration File # # This file is parsed by the Zaptel Configurator, ztcfg # # It must be in the module loading order # Span 1: WCTDM/0

Hello everyone, I want to connect a fax to an FXS port (TDM420P). For testing purposes, I connected an analogue phone to it first. However, when I pick it up, I cannot hear anything at all. The power cable is plugged into the card, the port is configured to use fxo-signalling. Also, immediate=no. Here's the files: /etc/zaptel.conf: # Autogenerated by /usr/sbin/genzaptelconf -- do not hand

The card you installed has FXO or FXS modules in it ????? are you getting your lines directly from the telco co??? Doug D On Mon 23/08/10 8:37 AM , Cassius Smith cassius at cassius.org sent: * -----Original Message----- * From: Todd Reese * Reply-to: Asterisk Users Mailing List - Non-Commercial Discussion * To: asterisk-users at lists.digium.com [3] * Subject: [asterisk-users] Dahdi

Looking for some help from the UK please. I backed up all my Asterisk configuration before re-installing the server from 32 -> 64 bit. Unfortunately I did not transfer the backup to another machine!!!!! I now have a TDM400P that is not picking up the line. Can you see what I have done wrong when I have rebuilt the config please: dahdi_scan ---------- [1] active=yes alarms=OK

Hi I was using the delivered Ubuntu 1.6.x packages but I wanted to look at gtalk integration so I downloaded, compiled and installed the source (after removing the Ubuntu packages) have installed the following: asterisk-1.8.0 dahdi-linux-complete-2.4.0+2.4.0 libpri-1.4.11.5 I copied my config back into place and most seems to work, but I cannot get my phone that is plugged into the Wildcard