similar to: Problem routing call to fax machine on DAHDI FXS port

[18884732963 at from-fax-machine:... - your call is hitting the from-fax-machine context - yet your 'fax' exten is in the from-pstn-4 context. See the "[2011-03-17 13:40:29.6] NOTICE[8825] chan_dahdi.c: Fax detected, but no fax extension" line. When Asterisk detects an incoming fax tone - it tries to automagically route the call to the 'fax' extension in the SAME

The card you installed has FXO or FXS modules in it ????? are you getting your lines directly from the telco co??? Doug D On Mon 23/08/10 8:37 AM , Cassius Smith cassius at cassius.org sent: * -----Original Message----- * From: Todd Reese * Reply-to: Asterisk Users Mailing List - Non-Commercial Discussion * To: asterisk-users at lists.digium.com [3] * Subject: [asterisk-users] Dahdi

I keep getting a red alarm when trying to setup asterisk to use my TE420B EC. I only have a blank context setup in my extensions.conf as I haven't started to config that until I can clear this red alarm. I don't have physical access to the server, so I can't go reseat the modules/card/ethernet cable, though I have hands on location that have done this a couple times

I am having problems getting a Nicherons TDM400P wildcard clone to dial out. Everything appears to be configured correctly, but although I see call progress, it never seems to actually pick up the phone. (The following is a test of 911 emergency, where I substitute 811 [repair service] as the actual number dialed.) *CLI> -- Executing [911 at from-internal:1]

Hello, My first attempt to get dahdi running on 1.4.28... with a Rhino 8 port modular card and a single FXS module. Got the Rhino card installed and the machine sees it: root at pbx:/etc/dahdi# dmesg | grep rcbfx [ 71.985309] rcbfx 0000:04:00.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21 [ 71.985440] rcbfx 1: Rhino PCI BAR0 50100000 IOMem mapped at ffffc90008d7c000 [ 71.985504]

Hi, I've seen this USB product from Sangoma : http://www.sangoma.com/products_and_solutions/hardware/analog_telephony/usb_fxo.html Is it working ok ? Is it easy to integrate it with Asterisk ? How would you rate your experience with it ? Regards -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi, Running 1.4.26.1 here. I have installed TE420B card in my server, and followed the appropriate steps (as far as I know to configure it). This TE420B is connected to a CLEC (T1s), so I am using pri_cpe as singalling type. When I dial out, I get this message: Dec 4 11:37:31] WARNING[27983]: app_dial.c:1275 dial_exec_full: Unable to create channel of type 'DAHDI' (cause 0

Hi All, I have installed asteriskNow with Asterisk 1.6.2.11 and FreePBX 2.7.0.10. I have configured x100p fxo card in my asterisk box. But in my cli mode i am not getting the command *"dahdi show status"* Output of CLI : astrisks*CLI> *dahdi show status* No such command 'dahdi show status' (type 'core show help dahdi show' for other possible commands) I

How can we set the CDR Master file to rollover at say 30 Meg and create a new one -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20100827/2e98385f/attachment.htm

Hello, I'm facing problem where as whenever there are incoming call from pstn, there will be no audio coming in. User at the other end also could not hear my voice. This happens few days back. Im using asterisk 1.6.1.2 with dahdi tool 2.2.0. I thought it was time to upgrade, so upgraded to dahdi 2.2.1 and asterisk 1.6.2.5. However, it does not help at all. My current config as follows :-

Hello I'd like to configure Asterisk so that... 1. I ring it from my cellphone with CID number displayed, just to notify Asterisk that I wish to make a call 2. Asterisk waits until I hang up, calls me back, and prompts me for the number I wish to call 3. Asterisk puts me on hold through Flash(), which is apparently the equivalent of hitting the R key on European handsets 4. Asterisk calls the

Hi list, Ive got a server with 6 ports on it (4+2 port card) we have a DS3 delivering all voice DS1's to us. Carrier has a trunkgroup for the first 8 span (we only have the first 6 plugged in right now). Everything works fine until we fail the primary D channel (D's are on 24,48) the secondary then picks up and outbound calls do not work, if we reboot Asterisk the D on 48 comes up and it

We have integrated an Asterisk (TE110P) and a Mitel SX200. We usually get over 500 frame errors and over a 500 slip errors per hour. When the errors reach 1000 per hour the Mitel will take it's T1 card offline. At that point no calls can be routed from the Asterisk server to the Mitel and the TE110P reports a Yellow alarm. What can be causing all these Frame and Slip errors? We have been

Hi, Built a new server at the weekend and install Asterisk 1.6.0.9 and IAX and SIP work great :) The one problem I am having is getting the OpenVox (TDM400 type card) to work. It is successfully identified using WCTDM kernel module and dahdi_scan picks it up just fine. The issue is when I try and setup dahdi_channel.conf as it fails everytime. When running asterisk -rvvvv I see the port pick

I have a 'CONGESTION' Status with R2 protocol. While testing this scenario sip GW--?Asterisk ?Digium E1 R2 Protocol?Cisco E1 R2 protocol?sip Gw Find below my error and configuration ,where are the errors in my configuration ? ========================================================================= Connected to Asterisk SVN-branch-1.6.2-r235775 currently running on

Some recent issues I had with hardware seem to come back to not understanding two very similarly named files: /etc/asterisk/dahdi-channels.conf /etc/asterisk/chan_dahdi.conf I've modified the chan_dahdi.conf to work now, but it would appear all I needed to do was include dahdi-channels.conf in chan_dahdi.conf and the problem would not have persisted? Is it me or is that a bit Monty Python?

Hi guys, I've been installing and configuring a TE110p card. The compile and install went very well. I'm using this on FC4 and I compile with linux26 as well checked I on the udev configs. zttool and ztcfg both indicate that the card is ready. But when I try to "load chan_zap.so" then I get the following Unable to load module chan_zap.so Jan 5 21:43:33 ERROR[6808]:

I have NFAS setup on several quad port T1 cards (Sangoma). It mostly works well with the exception that calls coming in on channels 48,72, and 96 have no audio. I tried removing these channels from zapata.conf with hopes that the channels would not come up or be used. Now I get "Ring requested on unconfigured channel". How can I busyout these these channels so that incoming

Hi I have been having a rough time getting a Sangoma A200/Remora FXO/ FXS Analog AFT card set up properly. The main issue is that the card has four ports and as far as I can tell Asterisk is only seeing two. On the two that it recognizes the "Green" FXS ports are not green, they just are not lit. The "RED" FXO ports are indeed red, but from what I have read your not

after installing asterisk 1.4.23.1 and dahdi-linux-2.1.0.4 and at CLI> module load chan_dahdi.so receive the following: signalling must be specified before any channels are. CLI> Warning [4663]: chan_dahdi.c:11627 process_dahdi: Ignoring signalling Error[4663]: chan_dahdi.c:10946 build_channels: Unable to reconfigure channel '1' Error[4663]: