similar to: Detect DTMF tone during call?

Hello, I have a customer who has their front door integrated to their current phone system. If someone presses the buzzer, the secretaries phone will ring, and she can talk to the person at the door. By pressing ** she can release the door. Anyone have any sort of integration like this. Are there IP devices anyone is using? They have a pizza box server as their asterisk server with

Hello all, i read a few articles online about the possibility to setup a "buzzer" door system to PBX using asterisk! currently my setup contains asterisk of course, and a sipura 3102.. what do i need to get such a feature done?! or should i ask if its possible?! _________________________________________________________________ Connect to the next generation of MSN Messenger?

Environment: Asterisk 1.2.14, FreePBX 2.2.0, Aastra 480i IP telephones firmware version 1.4.1.1077. Problem: Intercom feature: the dialed phone does not play the splash tone when auto-answering an intercom call. Otherwise, intercom works perfectly. Questions: What is the extensions.conf syntax to trigger a splash tone in Asterisk 1.2.14 (from the documentation and posts I've found, it has

Two days ago, I was talking on the phone from the FXO, to a SIP phone. After some time (like 1h30m), all of a sudden, there's a huge noise, like a buzz... Really loud. So I hungup, and called my asterisk box again... All I could hear was that sound. Someone called me from the internet, and as Asterisk dialed the FXO, all she heard was that noise too. So, I logged in my Asterisk server,

Hi everyone, I am looking for advice about the design of a SIP-based intercom. I count on your help, as my current attempts are not fruitful (yet). This will be a pretty long message, so here's my fundamental question: Is there a way to interpret DTMF tones sent by the calee (not the caller) while a voice call is in progress? Here's the desired scenario: - there is a box with

Hello We have setup a doorbell which has an inbuilt analog phone which is connected to our Asterisk via a SPA2000 ATA. The problem we are getting is that when a caller presses the buzzer it is taking two or more minutes to finally call the reception phone. In the SPA2000 I have set dtmfmode to be inband. I notice that with the asterisk you dial a number and then it waits for a timeout

Hi Lately I've been having problem with the handsets on the polycom phones. The agents are complaining that the humming/buzzing can be heard on random days. When the agents touch their computer the buzzing may increase louder or reduced. Also when they grab the handset cable, the buzzing noise is less loud and is loud again when I let it go. I have tried changing the handsets, problem not

I have an intermittent problem with the one FXS line that I have. On most calls, the first ~5 seconds of the call has a loud buzzing noise on the line. After 5 seconds or so, it fades off to nothing, and the sound quality is great. Searching for "buzzing" on the list doesn't give a whole lot to work with. The buzzing happens on calls that are routed over both my FXO line and

I have an extension that looks like this: exten => 5555551111,1,Verbose(Door buzzer calling) same => n,Dial(SIP/user1&SIP/user2&SIP/user3) The idea is that any of the three users can answer the phone to let someone in. The problem is that if, say, user2 unplugs his phone then the call immediately goes to his voice mail and the other two do not have the ability to open the door.

Hello rsync people Today I was recovering data from a beginning-to-fail external USB hard disk. I started with my usual 'rsync -av --ignore-errors <source> <dest>', and that was fine until it got to the first I/O errors. It paused but continued after the first couple of errors, but then the disk started buzzing and rsync gave error messages for every file (I'm afraid

There was a thread a few months ago that tossed around some ideas for using a cisco phone for intercom or paging. I don't have any ip phones, and wondered if anyone had any luck getting intercom or paging to work on the cisco units. Do any of the (cheaper) ip phones have a way to support intercom or paging? I presume that it's not part of the SIP or IAX protocols. Chris.

Hi All... I'm trying to get the intercom feature working on some snom 190 phones but having no luck... As you can see from the SIP trace below (from the called phone), intercom=true is being appended to the To: header as per requirements. I've email'd snom a few days ago but have yet to get a response. On my 190s, im running snom190-SIP 3.57v. I am pulling the config for the

Hi all, I have asterisk 1.4.26 (and I tried 1.4.29) connected PRI all 23 lines and for the most part everything works. Dialing out on 23 lines to phones works fine. I have to use the Local channel to call the intercom system (from call files). If I only call 1 intercom system at a time so it uses DAHDI/1 everything seems to work as I can call all 8 intercom systems and play a message. The

So I made the mistake of buying a Carrier Access channel bank without noticing the page on the wiki about the fact that they don't support disconnect supervision (bastards!). However, apart from that, I do have it working fine for incoming calls. Is there some trick to get asterisk to detect the hangup tones from SBC? I've tried busydetect and callprogress as suggested, but neither

Hello all, I'm having a problem with my intercom function that I use for under-chin paging. I'm running 1.6.2.13 on this server, and we use Linksys SPA-942's for our general phones. I have a global defined which has all the SIP channels concatenated together - this is ${ALL-PAGE-EXTS}. The problem comes when a user is on the line, and someone else uses the intercom function to page

Hello all, I noticed that Cisco claims that you can do station to station intercom with the 7940/7960 phones, and the Cisco Call Manager. Does anyone have an example SIP header that shows this in action? Or is it something else that triggers the intercom? I would like to add this in to *. Thanks, Mike

A friend pointed out this url http://www.cisco.com/univercd/cc/td/doc/pcat/clmn32.htm where it lists intercom/auto-answer as being a feature in Cisco Call Manager (which as I understand it, uses SIP predominately for handsets). I've come across comment somewhere that intercom isn't supported in the SIP spec. Does anyone know if the apparent capability of Intercom being available in SIP

Hello, We have 15 Soundpoint IP 500 phones and recently call quality has deteriorated. On some calls there is a static-buzzing of sorts that occurs when users talk. It can be picked up on SIP-SIP calls and SIP-ZAPTEL (Channel BANK<<-T100P). It basically sounds really weird whenever someone talks, it sounds like a bee buzzing or something. Very hard to explain. Also, there will be echo

Hi, Does anybody know of a VoIP compatible doorbell or door intercom unit? I've contemplated buying a cheap SIP phone, ripping it apart, and putting it inside an IP66 sealed unit... It would need: - At least one speed-dial key, or some way to make every button dial the same extension number - PoE (power over ethernet), so I can power it off the central switch - cheap enough to rip apart

Hello I just read this article about a kid in England who built a box with a 3G SIM card: www.dailymail.co.uk/sciencetech/article-1394448/Doorbell-tricks-burglars-thinking-youre-home-invented-schoolboy-Laurence-Rook-13.html When someone rings your intercom, the box will call your cellphone so you can answer just like you were home. I don't know anything about electronics and would like to