similar to: dahdi issue on digium AEX800

Hello I purchased an AEX800 card to replace the ageing cheap channel bank/T1 card solution a few months ago, assuming that it would be a more robust solution for my small scale phone system. However, it appears to be anything but that. Originally implemented as a XEN dom-u virtual machine on a large server class machine, using PCI passthrough to pass the AEX800 and a small older TDM400, then

Running Asterisk 1.6.2.9, DAHDI 2.3.0.1, CentOS 5.5 (update to date as of a week ago), I've installed a Digium AEX800P with 2 X400M FXO Modules and 1 VPMADT032 Module, hooked up to 5 analog lines. I get the error message referenced in the subject in my dmesg output everytime I load / reload DAHDI using the command "system dahdi start/restart". When I make an outbound call over

The Asterisk Development Team has announced the releases of: DAHDI-Linux 2.6.1 DAHDI-Linux 2.5.1 DAHDI-Tools 2.6.1 DAHDI-Tools 2.5.1 DAHDI-Linux-Complete 2.6.1+2.6.1 DAHDI-Linux-Complete 2.5.1+2.5.1 These releases are available for immediate download at: http://downloads.asterisk.org/pub/telephony/dahdi-linux http://downloads.asterisk.org/pub/telephony/dahdi-tools

The Asterisk Development Team has announced the releases of: DAHDI-Linux 2.6.1 DAHDI-Linux 2.5.1 DAHDI-Tools 2.6.1 DAHDI-Tools 2.5.1 DAHDI-Linux-Complete 2.6.1+2.6.1 DAHDI-Linux-Complete 2.5.1+2.5.1 These releases are available for immediate download at: http://downloads.asterisk.org/pub/telephony/dahdi-linux http://downloads.asterisk.org/pub/telephony/dahdi-tools

The TDM410P doesn't support 'hvac', only the obsolete TDM400P supports that option was for the old phones that have a neon light (or equivalent LED+ZENER ciruit). Are other phones off the TDM410P (other than the VTECH) working, or is the Vtech the only model with VMWI available to you. I'm not able to check at the moment, I have copied the asterisk-users list, someone else may

Good morning, I have a digium wctdm24xxp in my asterisk box, i am not able to see the callerid when the call is incoming from the fxo line, i live in Brazil, how can i change the signaling from fsk to dtmf? Thanks. -------------- next part -------------- An HTML attachment was scrubbed... URL:

When I compile dahdi I see these warnings: WARNING: "kasprintf" [dahdi-linux-2.5.0.2/drivers/dahdi/wctdm24xxp/wctdm24xxp.ko] undefined! WARNING: "kasprintf" [dahdi-linux-2.5.0.2/drivers/dahdi/dahdi.ko] undefined! And "modinfo dahdi" shows that the driver was built for a 2.6.17 kernel, SMP mod_unload 586 4KSTACKS gcc-4.1 If I "modprobe -a dahdi", I get

Hi, On a Lenny system, with dahdi 2.4.0, libpri 1.4.11.5 and asterisk 1.6.1.18, I inserted a new Digium HA8 + B400M card. My usual installation fails. I can see it listed : # lspci -n | grep d161 01:0b.0 0200: d161:8007 (rev 11) # lspci -vn 01:0b.0 0200: d161:8007 (rev 11) Subsystem: d161:8007 Flags: medium devsel, IRQ 22 I/O ports at d400 [size=256] Memory at

Hi Asterisk Users, We've been experiencing some tough time regarding a new Asterisk installation connected to the PSTN via an ISDN PRI with a Digium TE121 with the optional VPMADT032 echo cancellation module. For now, I'll focus on something very specific which is summarized on this email's subject. However, here are some general facts for the context: - System pbxfri went

Hi, On a (bogus) system equiped with a Digium HA8 and 8 BRI ports, I'm reading this: # asterisk -rx "dahdi show status" Description Alarms IRQ bpviol CRC4 Fra Codi Options LBO HA8-0000 RED 109 0 0 CCS AMI YEL 0 db (CSU)/0-133 feet (DSX-1) HA8-0000 UNCONFI 109 0

The Asterisk Development Team has announced the releases of: DAHDI-Linux-v2.8.0-rc5 DAHDI-Tools-v2.8.0-rc5 dahdi-linux-complete-2.8.0-rc5+2.8.0-rc5 This release is available for immediate download at: http://downloads.asterisk.org/pub/telephony/dahdi-linux http://downloads.asterisk.org/pub/telephony/dahdi-tools http://downloads.asterisk.org/pub/telephony/dahdi-linux-complete *** THIS RC FIXES

The Asterisk Development Team has announced the releases of: DAHDI-Linux-v2.8.0-rc5 DAHDI-Tools-v2.8.0-rc5 dahdi-linux-complete-2.8.0-rc5+2.8.0-rc5 This release is available for immediate download at: http://downloads.asterisk.org/pub/telephony/dahdi-linux http://downloads.asterisk.org/pub/telephony/dahdi-tools http://downloads.asterisk.org/pub/telephony/dahdi-linux-complete *** THIS RC FIXES

I have a AEX800 PCI Express card - sort of a TDM800 with PCI-Express. (or AEX844 - 4FXS & 4FXO) I downloaded Asterisk Now - and have got this loaded on a new motherboard (Intel with 3 PCI, 3 PCI Express - etc). (Downside on PCI-Express is the physical support the express slot gives (very little) compared with an 'old' standard PCI slot!!!) With only this card in the box....

Dear, I have Asterisk 1.6 with an E1 Digium card with echo cancellation module. So I need to use just the echo cancellation by hardware and disable the echo cancellation by software. I use DAHDI for my telephony hardware. If the lines involved with echo cancel are: In /etc/dahdi/system.conf: echocanceller=mg2,1-15,17-31 In /etc/asterisk/chan_dahdi.conf: echocancel=yes echocancelwhenbridged=no

Hi all, What hell hapen here? asterisk:/etc/asterisk# /etc/init.d/dahdi startLoading DAHDI hardware modules:FATAL: Error inserting dahdi (/lib/modules/2.6.26-2-686/dahdi/dahdi.ko): Device or resource busy wct4xxp: done wcte12xp: done wct1xxp: done wcte11xp: done wctdm24xxp: done wcfxo: done wctdm: done wcb4xxp: error wctc4xxp: done xpp_usb: doneError: missing /dev/dahdi! When

I am running Asterisk 1.16.2.13, dahdi 2.4.0 and libpri 1.4.11.4 on an HP ML110 G6 using Ubuntu Linux 10.04 LTS. I have two Digium TE121 single T1 port cards and a Digium AEX800 8-port FXS card. All PCI Express cards. Co-workers are hearing hissing sounds on some calls, and I am getting IRQ errors when running "dahdi show status". I see that sharing IRQs for Digium cards isn't

Hi, I'm facing an issue with which loading wctdm24xxp module fails. Here is relevant dmesg's output : [ 13.455729] dahdi: Telephony Interface Registered on major 196 [ 13.455729] dahdi: Version: 2.4.0 [ 13.510847] ACPI: PCI Interrupt 0000:01:0b.0[A] -> GSI 22 (level, low) -> IRQ 22 [ 15.527788] wctdm24xxp 0000:01:0b.0: Timeout waiting for receive frame. [ 17.527787]

Hi gang, We are moving our computers from a cluster of physical machines to a VMWARE server with virtual machines. We investigated and are looking to replace our TDM400P/TDM410P with AEX410P cards. Can we run asterisk with the DAHDI drivers from one of the Virtual machines or is DAHDI going to have to be a native process on the "REAL" machine? Thanks Danny Nicholas

Hi list, I installed 2 HB8 cards each of them with a Quad Bri modules in a HP 360 G6 running Debian Squeeze. Here is an output of dmesg wafter server has booted: [ 9.784123] wctdm24xxp 0000:0b:08.0: PCI INT A -> GSI 31 (level, low) -> IRQ 31 [ 11.847073] bnx2: eth0 NIC Copper Link is Up, 1000 Mbps full duplex [ 11.847600] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [

Have a new TE133 in a dell R320. dahdi_cfg -vvv shows: DAHDI Tools Version - 2.9.1 DAHDI Version: 2.9.1 Echo Canceller(s): Configuration ====================== SPAN 1: ESF/B8ZS Build-out: 0 db (CSU)/0-133 feet (DSX-1) Channel map: Channel 01: Clear channel (Default) (Echo Canceler: mg2) (Slaves: 01) Channel 02: Clear channel (Default) (Echo Canceler: mg2) (Slaves: 02) Channel 03: Clear