similar to: Dahdi issue with Asterisk 1.8.0

I am running Asterisk 1.6.2.17.2 with a Openvox A400 card with 2FXO/2FXS modules. I'm trying to set-up things to route analog fax calls from a FXO port to an analog fax machine on a FXS port on the same card. Outgoing faxes work just fine. But incoming faces are routed to the right DAHDI extension, but the call dropped right as the fax machine rings for the first time. The fax machine

As best i could figure it out, I've installed dahdi and rc4. My TDM400P doesn't answer fxo or fxs. /etc/dahdi/system.conf: loadzone = us defaultzone=us fxoks=1,2 fxsks=4 /etc/asterisk/chan_dahdi.conf: [house-phones] context=internal ; Uses the [internal] context in extensions.conf signalling=fxo_ks ; fxo_ks Use FXO signalling for an FXS chanel dahdichan => 1 ;

Looking for some help from the UK please. I backed up all my Asterisk configuration before re-installing the server from 32 -> 64 bit. Unfortunately I did not transfer the backup to another machine!!!!! I now have a TDM400P that is not picking up the line. Can you see what I have done wrong when I have rebuilt the config please: dahdi_scan ---------- [1] active=yes alarms=OK

after installing asterisk 1.4.23.1 and dahdi-linux-2.1.0.4 and at CLI> module load chan_dahdi.so receive the following: signalling must be specified before any channels are. CLI> Warning [4663]: chan_dahdi.c:11627 process_dahdi: Ignoring signalling Error[4663]: chan_dahdi.c:10946 build_channels: Unable to reconfigure channel '1' Error[4663]:

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi all! Days ago I bought a OpenVox A400P card with a port FXS and another FXO that I am testing with my Asterisk installation in my house. I'm using Asterisk 1.4.24.1 with DAHDI Linux 2.1.0.4 and DAHDI Tools 2.1.0.2 on Debian GNU/Linux Lenny. I was reading "The future of telephony" and this [1] document looking for information about

Hi, I am using TDM400 card with 3 fxs and 1 fxo. I am struggling to detect hangup tone or disconnect supervision tone from my CO. I attached the recorded wav file which contains my telco's disconnect supervision. I am using , asterisk-1.4.33.1 dahdi-linux-complete-2.3.0.1+ 2.3.0 OS => Debian-lenny 5 users.conf ------------- [trunk_1] trunkname = pstn ; GUI

Hi, I've seen this USB product from Sangoma : http://www.sangoma.com/products_and_solutions/hardware/analog_telephony/usb_fxo.html Is it working ok ? Is it easy to integrate it with Asterisk ? How would you rate your experience with it ? Regards -------------- next part -------------- An HTML attachment was scrubbed... URL:

I am having problems getting a Nicherons TDM400P wildcard clone to dial out. Everything appears to be configured correctly, but although I see call progress, it never seems to actually pick up the phone. (The following is a test of 911 emergency, where I substitute 811 [repair service] as the actual number dialed.) *CLI> -- Executing [911 at from-internal:1]

Hi, Built a new server at the weekend and install Asterisk 1.6.0.9 and IAX and SIP work great :) The one problem I am having is getting the OpenVox (TDM400 type card) to work. It is successfully identified using WCTDM kernel module and dahdi_scan picks it up just fine. The issue is when I try and setup dahdi_channel.conf as it fails everytime. When running asterisk -rvvvv I see the port pick

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi all! I'm testing a telephone connected to FXS port of a Sangoma A200 card. But I'm observing that callerid is not working. The configuration that I'm using in chan_dahdi.conf is the following one: - --------------------------------------------------------------------- ;autogenerated by /usr/sbin/wancfg_dahdi do not hand edit

The card you installed has FXO or FXS modules in it ????? are you getting your lines directly from the telco co??? Doug D On Mon 23/08/10 8:37 AM , Cassius Smith cassius at cassius.org sent: * -----Original Message----- * From: Todd Reese * Reply-to: Asterisk Users Mailing List - Non-Commercial Discussion * To: asterisk-users at lists.digium.com [3] * Subject: [asterisk-users] Dahdi

Hello, My first attempt to get dahdi running on 1.4.28... with a Rhino 8 port modular card and a single FXS module. Got the Rhino card installed and the machine sees it: root at pbx:/etc/dahdi# dmesg | grep rcbfx [ 71.985309] rcbfx 0000:04:00.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21 [ 71.985440] rcbfx 1: Rhino PCI BAR0 50100000 IOMem mapped at ffffc90008d7c000 [ 71.985504]

Hi I have been having a rough time getting a Sangoma A200/Remora FXO/ FXS Analog AFT card set up properly. The main issue is that the card has four ports and as far as I can tell Asterisk is only seeing two. On the two that it recognizes the "Green" FXS ports are not green, they just are not lit. The "RED" FXO ports are indeed red, but from what I have read your not

I've got a single TDM 400P board with two internal ports and 1 external. chan_dahdi.conf: context=internal ; Uses the [internal] context in extensions.conf signalling=fxo_ks ; fxo_ks not auto Use FXO signalling for FXS group=0 channel => 1 ; Telephone attached to port 1 channel => 2 ; Telephone attached to port 2 context=incoming-pstn-line ; Incoming calls

From asterisk -cvvvvv == Parsing '/etc/asterisk/chan_dahdi.conf': == Found == Parsing '/etc/asterisk/users.conf': == Found -- Automatically generated pseudo channel [Nov 11 17:43:28] WARNING[5756]: chan_dahdi.c:18155 process_dahdi: Ignoring any changes to 'userbase' (on reload) at line 23. [Nov 11 17:43:28] WARNING[5756]: chan_dahdi.c:18155 process_dahdi:

I am unable to dial out over a Wildcard TDM400P. This was working previously, so must have messed up the config somehow. I'm running Asterisk 1.6.0.15, with FreePBX 2.5.2.2. When I dial, I see: -- Executing [s at macro-dialout-trunk:19] Dial("DAHDI/1-1", "DAHDI/g0/9239220,300,") in new stack == Everyone is busy/congested at this time (1:0/1/0) It looks like the

[18884732963 at from-fax-machine:... - your call is hitting the from-fax-machine context - yet your 'fax' exten is in the from-pstn-4 context. See the "[2011-03-17 13:40:29.6] NOTICE[8825] chan_dahdi.c: Fax detected, but no fax extension" line. When Asterisk detects an incoming fax tone - it tries to automagically route the call to the 'fax' extension in the SAME

Hi, I've just installed DAHDI at two PBXs as follows: *PBX-1 PBX-2* FXO ------------- FXS When I try to send calls from PBX-1 to PBX-2 I just receive the message: "Starting simple switch on 'DAHDI/1-1" It seems like if PBX-1 couldn't send DTMFs, but when I set immediate=yes at chan_dahdi.conf at PBX-2 dialplan is executed at PBX-2 but nothing is heard at

Hello, Is it possible, for testing, to connect an cat5 straight patch cord between 2 ports of a Digium B410P card and use these 2 ports as a normal dahdi trunk ? I've tried this: One port is set as NT, the other as TE. I would expect timing to come for system hardware so I choose in /etc/dahdi/system.conf : span=1,0,0,ccs,ami span=2,0,0,ccs,ami Results: - both ports lights are green -

Hello On a brand new CentOS 5.5 host, I wanted to install Dahdi before installing Asterisk 1.4.x. So I untarred dahdi-linux-complete-2.4.0+2.4.0.tar.gz, followed by make, make install, make config. Next, I created the following files from scratch: ============ /etc/modprobe.d/dahdi.conf: options wctdm opermode=FRANCE ============ /etc/dahdi/modules wctdm ============ /etc/dahdi/system.conf