similar to: S110M not working

I've been using my Asterisk (At my house - 2 modem-type fxos, and an assortment of SIP endpoints for phones) for about 5 weeks now, and I've been really happy with it, but I'm still having an echo problem that I've exhausted google with, and can't get straight... I think I've determined that because I'm using $7 voice modem clones for my FXOs that bad echo is going to

Hello group, I am installing Asterisk on a new pc running Ubuntu 12.04.3 Server. ?I have dahdi-complete-2.7.0.1+2.7.0.1, and have tried 2.6.1 and 2.8.0-rc1 and 2.8.0-rc2. ?I am following along in the ASTERISK The Definitive Guide 4th Edition and on page 116 when I issue the command $ sudo /etc/init.d/dahdi start I get the following error: Loading DAHDI hardware modules: ? ?wctdm24xxp: done

Hi I am fairly new to Asterisk. I will have few questions on one Asterisk system: Description: I looked at Asterisk Mall says that "The TrueLine SMB PBX is perfect for the small office providing service for up to 28 Telco lines". This is a 1U Rack Mount Single T1 Asterisk Appliance. Question: Does it mean it has 7 PCI bus and takes 7x4=28 channels (if they used 7 TDM400P card

I just picked up a couple CAC Access Bank 1s loaded with FXS that should be arriving shortly. Does anyone have one that they use with Asterisk? If so, would you be willing to shoot me a note with your current configs? I'm not very familiar with CAC/etc, and it would save me countless hours of muddling through .. :) Any others tips you can give me on these banks would be very

I have a TDM21B (A new TDM20B that just arrived plus a X100M that I already had). This card sometimes works, and sometimes only the FXO module is seen. (correction to previous message that incorrectly listed X400M/S400M when I'm using only the single port versions of these modules (X100M/S110M). By "works", I mean all 3 modules have the green lights on the ports on and when

Hi all, I just got my long awaited FXS modules for a TDM400 card, and was a bit puzzled about how my phones and the FXS interface worked together. Here goes: In Sweden (that's where I am located) phones traditionally are connected in daisy chain configuration. This means that a phone in on-hook condition passes the line through back onto the outer pair of the RJ11, back into the wall

Having ISDN FXOs and a bunch of ISDN DECT base stations, I went looking for a CAPI compatible active BRI adapter capable of NT mode. I have found that the 'Eicon Diva Server 4BRI' fulfills theses requirements. However, at EUR 1387 for four BRI interfaces, it does not come cheap. Are there other users of similar hardware that can point me to alternatives ?

I have a TMD400 card installed in a PC with one fxs (installed in slot 2) and two fxos (installed in slots 3 & 4).? fxos work fine but I am unable to get a dial tone for any devices connected to the fxs.? I have correctly connected the power supply to the card and I have even tried moving the card from slot 1 to 2 on the board. Below is from the console when I try to route a call from FXO on

Does anyone on-list have direct experience with the new analog cards from Sangoma? I'm thinking about FXOs with echo cans. Need 2-4 ports but don't want to go through another TDM400 style experience. Michael -- Michael Graves mgraves@pixelpower.com Sr. Product Specialist www.pixelpower.com Pixel Power Inc.

Hi, I am trying to read the "credit.lisp" file of the Japanese credit database in UCI repository, but it is in lisp format which I do not know how to read. I have not found how to do that in the foreign library http://archive.ics.uci.edu/ml/datasets/Japanese+Credit+Screening <http://archive.ics.uci.edu/ml/datasets/Japanese+Credit+Screening> Could anyone help me? Best

Been using a few different FXO interfaces (X100P, Voicetronix, and SPA-3000) at a couple sites and they've all run into nasty issues at times. I'm looking at moving one of my offices and am in the market for a solution for connecting 4 FXOs. I got excited about recent offerings from Digium and Sangoma in the way of new cards but I hear they're causing troubles for more than a few.

helleo ,I have one wildcard installed on the server,and configured it.there are two modules which both FXOs .all configurations complete,and when we start asterisk use "asterisk -vvvvc",it shows asterisk ready,no warnings.afterwards when the sever connected to the PSTN in the one port which configured,and have a phone line connected to the other port then run

Hi, I have pushed my radio player for FxOS to GitHub: https://github.com/emilis/worldradioplayer Currently it uses a precompiled data from http://dir.xiph.org/yp.xml: https://raw.github.com/emilis/worldradioplayer/master/static/js/data/xiph.org.stations.json I will have to switch to asynchronous station list loading and filtering in the near future and then will nag you again about the JSON API

Hi, I am trying to do the world's most simple install. I have a Wildcard TDM400P with 3 ports: 1 FXS on port 1 and 2 FXOs on ports 3 and 4. (i'm not using port 3 for now, put want it for expansion purposes) I simply (to start with) am looking to have the FXS phone ring when an FX0 port is dialed. I would also like to be able to place outgoing calls on the FXS through the FXO. Right

Hey all, I've been seeing this repeatedly and am wondering if anyone has a clue what's causing it.. at least once a day I see two zap fxo channels being bridged, and hanging..now, these two channels should never bridge, but they keep doing it.. any leads on where to look for what's causing it? here's what I see when I 'show channels' Zap/37-1 s@from-pstn:1

I have a box with 12 T1s (4 Te410P cards). The PSTN provider is reporting slips and ask me to update the clock source. I have my system.conf set as the following but when I run dahdi_scan only the ports on Card 1 are showing up with syncsrc=1 system.conf : span=1,1,0,esf,b8zs bchan=2-24 mtp2=1 span=2,2,0,esf,b8zs bchan=26-48 mtp2=25 span=3,3,0,esf,b8zs bchan=49-72

Hi all, We have an analog line from telco, on which 3-way calling is subscribed to. This line is plugged into an FXO module on a tdm400p. If an incoming call comes in on this line, can */zaptel send Flash to telco via the FXO module? If it could, then an incoming call could be 'transfered' to a cell-phone, for example, with a single analog line. (where 'transfer' is really

I'm rolling out an installation with snom 360s in the near future. Simple SOHO configuration, 3 FXOs hanging off a TDM400B, 4 snom 360s, a snom 200, some variant of IAX softphone, and an IAXy or Sipura 2002. I have the 360's set up to subscribe and notify for the line use lights, which works like a charm for interoffice calling (between the 360's, anyway. The IAXy, 200 and,

The card you installed has FXO or FXS modules in it ????? are you getting your lines directly from the telco co??? Doug D On Mon 23/08/10 8:37 AM , Cassius Smith cassius at cassius.org sent: * -----Original Message----- * From: Todd Reese * Reply-to: Asterisk Users Mailing List - Non-Commercial Discussion * To: asterisk-users at lists.digium.com [3] * Subject: [asterisk-users] Dahdi

Hello! I am trying to configure my digium TE220 dual-span pci express card with Dahdi. I seemed to have managed to set up the card with the Dahdi kernel, as demonstrated by executing dahdi_scan: [1] active=yes alarms=RED description=T2XXP (PCI) Card 0 Span 1 name=TE2/0/1 manufacturer=Digium devicetype=Wildcard TE220 (4th Gen) location=Board ID Switch 0 basechan=1 totchans=31 irq=16