similar to: E1 channels real time monitoring

Dear all, I have to install an E1 card in my Asterisk 1.4.23 server and here is my short question: Is it necessary to install or update any Asterisk/Zaptel/Any extra module or the default installation is good enough to just plug and run the E1 card ???? Thanks a lot Alejandro

Dear, I have two Asterisk PBXs with an E1 interface/RJ-45 port in both boxes. I need to connect both PBXs with E1/R2 and UTP cable. What are the requirements to deploy the UTP cable ??? Straight-through or crossover ??? What are the pinouts in both peers ??? Thanks a lot, Alejandro

Hi, I have been trying to get a Wildcard TE122 card running here the last couple of days. libpri and zaptel are all installed and configured to E1 specs. The jumper on the card is on, so configured for E1 (I'm in Norway). When running zttool, I get 'Alarms: RED' on the single card installed. Other information in zttool: Current alarms: Red Alarm Sync source: Internally clocked

Dear, I have asterisk 1.6.2.13 in a small hardware PBX (512 GB RAM and Celeron), and last days when I call from one extension to another of the same PBX after I dial the number the rings sound after 20 seconds. In the CLI log, when I debug the AGI, I see always goes good until dialparties.agi, and after that there are 20 seconds without any log, and so the ring sound. I've read

I have recently built a single-T1 Asterisk box using an HP DL120G6 with a Digium TE122 card. I was finding that I was getting missed interrupts on the TE122, causing the driver to report that it was increasing latency. It kept doing this until the T1 did not work reliably. I tried my usual procedure of disabling the USB subsystem in the BIOS (or so I thought), but I found that the USB drivers

Dear all, I have an Asterisk SIP server in a LAN environment and I want your opinion in order to decide the use of an audio codec: What audio codec is better, G.711a or G.711u ??? Which suites to my LAN voip calls ??? Thank you !!! Alejandro -------------- next part -------------- An HTML attachment was scrubbed... URL:

Dear, I need to create a custom device extension in order to dial a local queue. Suppose my queue number is 8888, how can fill the Dial field from the custom extension ??? Because if I put just 8888 or Local/8888, I don't succeed. Thanks a lot

Does anyone know if the TE122 is recognized by any of the 1.2 zaptel drivers? It seems that 1.2.16 knows it not... :) Cheers, j

I have setup a asterisk with freepbx, a TE122 and i have an ISDN. My problem now is that callers are experiencing echo. checked on dmesg i saw this: # dmesg -c dahdi: Disabled echo canceller NLP because of CED rx detected on channel 2 i searched google but found no soolution and i have no idea what that error means. below are other details that might be of value. # dahdi_hardware

lspci | grep Digium 03:05.0 Ethernet controller: Digium, Inc. Wildcard TE122 single-span T1/E1/J1 card (rev 11) dahdi_scan So I have a card in a box - lspci shows it... dahdi_scan reports nothing. Is my card dead? Jerry -------------- next part -------------- An HTML attachment was scrubbed... URL:

What's the difference between the TE121 and TE122. I read the description on Digium's site and it isn't clear to me. Best regards, -- Guilherme Loch G?es Visite nossa loja virtual: http://www.shopvoip.com.br Not?cias e F?rum sobre VoIP com software livre: http://www.asteriskexperts.com.br -------------- next part -------------- An HTML attachment was scrubbed... URL:

Dear all, I need to build a PBX based on Asterisk for a call center. I have worked with raw Asterisk but it's hard to work for big implementations think. Also I have worked with Trixbox CE for a small bussines and it was prette good, but I have not have many features like ACD. I know there is another version called Trixbox PRO -specially Call Center edition- that's not free but has got

Dear, I always had one E1 card with one span, so I've never had any problem in set it up through /etc/dahdi/sustem.conf and /etc/asterisk/chan_dahdi.conf because I put span=1. But now I have a PBX with two E1 cards with 4 span (8 span in total). How do I have to define both card in system.conf and chan_dahdi.conf, and how do I have to refer each span to the corresponding card ??? Thanks a

Does anyone know if I could use modprobe command to find out rather than set the jumper on a Digium PRI card? I want to find out the jumper settings on the card without opening the box which will cause down time. Thanks. -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi, I have a Dell Power Edge server & planning yo buy Sangoma A101D card. To configure with my Asterisk 1.2.18 & zaptel-1.2.17.1 & Free-PBX setup. So I wanted to know the steps & any issue which I may come accross if any. I have googled & have some docs handy wrt Trixbox-2.2. Just wanted to get some notes from user with custom install setup when used with

Hi Guys, Anyone might know why this error keeps showing up and inbound/outbound is not working on a Bell PRI with Sangoma A101D? -- Got SABME from network peer. Sending Unnumbered Acknowledgement No calls can be made inbound/outbound. Keeps repeating. No alarms ON and no changes been made to the system. Stopped all a sudden. Asterisk CLI doesn't show anything with full verbose for both

I am trying to get a zaptel install converted to dahdi. I can get dahdi installed, and the pseudo device even shows up; however, dahdi show channels shows me nothing. There is a TE122 and a TDM800 in there, and neither show up. dahdi show status shows both cards, and dahdi tools show that the cards are there, working, and have no alarms. What am I missing? Michael Munger, dCAP, MCPS, MCNPS,

Just wondering how your experience is with HPEC, Is it just for analog interfaces or we can use it on TE122 as well? -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20080214/3f0580f1/attachment.htm

Hello, I am installing dahdi on a machine lspci 00:00.0 Host bridge: Intel Corporation 3200/3210 Chipset DRAM Controller (rev 01) 00:01.0 PCI bridge: Intel Corporation 3200/3210 Chipset Host-Primary PCI Express Bridge (rev 01) 00:06.0 PCI bridge: Intel Corporation 3210 Chipset Host-Secondary PCI Express Bridge (rev 01) 00:1a.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI

Hello Everyone. We have: Asterisk 1.4.21.2 zaptel-1.4.11 libpri-1.4.5 Sangoma A101D Connected to a PRI Cicso 7960G phones (About 30 of them) We have a problem with dropped calls that has going on for a long time. We get up to 5 dropped calls on a bad day. They all seem to be incoming calls. I have a recording of what my users report a dropped call sounds like right before it drops