similar to: Problem with new AEX800 card dying because of interrupt problems

I have a AEX800 PCI Express card - sort of a TDM800 with PCI-Express. (or AEX844 - 4FXS & 4FXO) I downloaded Asterisk Now - and have got this loaded on a new motherboard (Intel with 3 PCI, 3 PCI Express - etc). (Downside on PCI-Express is the physical support the express slot gives (very little) compared with an 'old' standard PCI slot!!!) With only this card in the box....

Hi All, I have installed asterisk 1.6.2.8 Dahdi: 2.4.0 Digium card: Digium, Inc. Wildcard AEX800 8-port analog card I have configured this card properly and it is working for calls too, But there is issue of one way audio on this outbound routes only, My voice is going to outside pstn number but i am not able to get their audio, I have disabled firewall, selinux is also off. If I am applying

Running Asterisk 1.6.2.9, DAHDI 2.3.0.1, CentOS 5.5 (update to date as of a week ago), I've installed a Digium AEX800P with 2 X400M FXO Modules and 1 VPMADT032 Module, hooked up to 5 analog lines. I get the error message referenced in the subject in my dmesg output everytime I load / reload DAHDI using the command "system dahdi start/restart". When I make an outbound call over

Hi list, I installed 2 HB8 cards each of them with a Quad Bri modules in a HP 360 G6 running Debian Squeeze. Here is an output of dmesg wafter server has booted: [ 9.784123] wctdm24xxp 0000:0b:08.0: PCI INT A -> GSI 31 (level, low) -> IRQ 31 [ 11.847073] bnx2: eth0 NIC Copper Link is Up, 1000 Mbps full duplex [ 11.847600] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [

Quick and dirty question: for the TDM410P I must use the wctdm24xxp driver? Att Vin?cius Fontes Desenvolvimento Canall Tecnologia em Comunica??es Ltda.

Hi dears, I am from saudi arabia and using asterisk 1.6.2.13,Dahdi-2.3.0 and Digium, Inc. Wildcard AEX800 8-port analog card (PCI-Express) . I am facing problem with detecting caller id before first ring.I recorded the dahdi channel using dahdi_monitor command. Where I am able to see and hear caller-id dtmf tones. Pl tell me the procedure to upload recorded file if you needed. Something I want

Hi All, This is a request for testing for users of Asterisk 1.4 or 1.6 with any of the following Digium VoiceBus based cards: TDM2400P, AEX2400, AEX800, TDM800P, TDM410, TE120P, TE121, and/or TE122. From a practical standpoint, this branch should allow these boards to work in more systems / configurations where IRQ misses caused problems in the past. The updated wctdm24xxp and wcte12xp

Hi, I'm facing an issue with which loading wctdm24xxp module fails. Here is relevant dmesg's output : [ 13.455729] dahdi: Telephony Interface Registered on major 196 [ 13.455729] dahdi: Version: 2.4.0 [ 13.510847] ACPI: PCI Interrupt 0000:01:0b.0[A] -> GSI 22 (level, low) -> IRQ 22 [ 15.527788] wctdm24xxp 0000:01:0b.0: Timeout waiting for receive frame. [ 17.527787]

Hi, On a Lenny system, with dahdi 2.4.0, libpri 1.4.11.5 and asterisk 1.6.1.18, I inserted a new Digium HA8 + B400M card. My usual installation fails. I can see it listed : # lspci -n | grep d161 01:0b.0 0200: d161:8007 (rev 11) # lspci -vn 01:0b.0 0200: d161:8007 (rev 11) Subsystem: d161:8007 Flags: medium devsel, IRQ 22 I/O ports at d400 [size=256] Memory at

Hi, 1. Is there any manual entry about modprobe's options relative to a given Dahdi driver (wctdm24xxp, for instance) ? 2. When loading a wctdm24xxp driver, is there any parameter to pass to modprobe to configure a span in NT/point to point mode ? 3. After running dahdi_cfg -vvvvv , I can read with dmesg : [ 1986.289277] wctdm24xxp 0000:04:06.0: xhfc: Configuring port 0 span 1 in TE mode

I am running Asterisk 1.16.2.13, dahdi 2.4.0 and libpri 1.4.11.4 on an HP ML110 G6 using Ubuntu Linux 10.04 LTS. I have two Digium TE121 single T1 port cards and a Digium AEX800 8-port FXS card. All PCI Express cards. Co-workers are hearing hissing sounds on some calls, and I am getting IRQ errors when running "dahdi show status". I see that sharing IRQs for Digium cards isn't

Hi, sorry for my insistence but this is a big problem for me..my steps for remove card are ok ? Thanks. ------ Salvatore. ----- Original Message ----- From: "Sasa" <sasa at shoponweb.it> To: <asterisk-users at lists.digium.com> Sent: Monday, November 26, 2007 4:25 PM Subject: [asterisk-users] Remove a TDM Card > Hi, I would like remove a Digium TDM2400P from

Hi. Please help. When trying to compile Zaptel 1.4.5.1 I get the following: /build/include/linux/modversions.h -DSTANDALONE_ZAPATA -I.. -o base.o -c base.c base.c:48:29: linux/workqueue.h: No such file or directory base.c:292: warning: `vpm150m_firmware' defined but not used make[2]: *** [base.o] Error 1 make[2]: Leaving directory `/usr/src/zaptel-1.4.5.1/wctdm24xxp' make[1]: ***

Hi, Before I report a bug on http://bugs.digium.com, I would like to know if someone is seeing the same error message. Personally I am not using wctdm24xxp but other modules such as wcte12xp and wctdm. The latter modules load fine and are compiled with pci_register_driver as expected. The only module that seems to require the deprecated function pci_module_init is wctdm24xxp. Is this normal?

I'm trying to configure a TDM808P card on debian. When I modprobe wctdm24xxp i get this error FATAL: Module wctdm24xxp not found. FATAL: Error running install command for wctdm24xxp I think i have successfully compiled the zaptel drivers, and the card appears when i do a lspci 02:06.0 Ethernet controller: Digium, Inc. Unknown device 0800 (rev 11) Subsystem: Digium, Inc. Unknown

Hi, I'm running FC3 with kernel 2.6.11. All the binary files and zaptel kernel modules is not available to system at boot time. They are extracted in a ram disk at system startup and then zaptel modules are loaded manually and so on. I have no problem with this boot routine and i've been tested all digium cards (expect tdm24) and they work fine till now. The problem appeared when i

When I compile dahdi I see these warnings: WARNING: "kasprintf" [dahdi-linux-2.5.0.2/drivers/dahdi/wctdm24xxp/wctdm24xxp.ko] undefined! WARNING: "kasprintf" [dahdi-linux-2.5.0.2/drivers/dahdi/dahdi.ko] undefined! And "modinfo dahdi" shows that the driver was built for a 2.6.17 kernel, SMP mod_unload 586 4KSTACKS gcc-4.1 If I "modprobe -a dahdi", I get

Hi All, Running asterisk 11.25.3, the /proc/cpuinfo says Intel(R) Xeon(R) CPU X5675 @ 3.07GHz lsmod | grep dahdi gives dahdi_transcode 16384 1 wctc4xxp dahdi_voicebus 61440 2 wctdm24xxp,wcte12xp dahdi 225280 11 wctdm24xxp,wcfxo,wctdm,dahdi_transcode,oct612x dahdi_voicebus,wcb4xxp,wct1xxp,wct4xxp,wcte11xp,wcte12xp crc_ccitt 16384 2

Have a new TE133 in a dell R320. dahdi_cfg -vvv shows: DAHDI Tools Version - 2.9.1 DAHDI Version: 2.9.1 Echo Canceller(s): Configuration ====================== SPAN 1: ESF/B8ZS Build-out: 0 db (CSU)/0-133 feet (DSX-1) Channel map: Channel 01: Clear channel (Default) (Echo Canceler: mg2) (Slaves: 01) Channel 02: Clear channel (Default) (Echo Canceler: mg2) (Slaves: 02) Channel 03: Clear

The Asterisk Development Team has announced the releases of: DAHDI-Linux 2.6.1 DAHDI-Linux 2.5.1 DAHDI-Tools 2.6.1 DAHDI-Tools 2.5.1 DAHDI-Linux-Complete 2.6.1+2.6.1 DAHDI-Linux-Complete 2.5.1+2.5.1 These releases are available for immediate download at: http://downloads.asterisk.org/pub/telephony/dahdi-linux http://downloads.asterisk.org/pub/telephony/dahdi-tools