similar to: Dahdi install gone wrong

I am having problems getting a Nicherons TDM400P wildcard clone to dial out. Everything appears to be configured correctly, but although I see call progress, it never seems to actually pick up the phone. (The following is a test of 911 emergency, where I substitute 811 [repair service] as the actual number dialed.) *CLI> -- Executing [911 at from-internal:1]

I am running Asterisk 1.6.2.17.2 with a Openvox A400 card with 2FXO/2FXS modules. I'm trying to set-up things to route analog fax calls from a FXO port to an analog fax machine on a FXS port on the same card. Outgoing faxes work just fine. But incoming faces are routed to the right DAHDI extension, but the call dropped right as the fax machine rings for the first time. The fax machine

Hi, I've seen this USB product from Sangoma : http://www.sangoma.com/products_and_solutions/hardware/analog_telephony/usb_fxo.html Is it working ok ? Is it easy to integrate it with Asterisk ? How would you rate your experience with it ? Regards -------------- next part -------------- An HTML attachment was scrubbed... URL:

Looking for some help from the UK please. I backed up all my Asterisk configuration before re-installing the server from 32 -> 64 bit. Unfortunately I did not transfer the backup to another machine!!!!! I now have a TDM400P that is not picking up the line. Can you see what I have done wrong when I have rebuilt the config please: dahdi_scan ---------- [1] active=yes alarms=OK

Hello, After installing on Ubuntu 10.04 using the tutorial on http://hmontoliu.blogspot.com/2010/03/installing-asterisk-and-freepbx-on.html I have a running instance of Asterisk. PROBLEM: result of dahdi_cfg: DAHDI Tools Version - 2.2.1 DAHDI Version: 2.2.1 Echo Canceller(s): MG2 Configuration ====================== Channel map: Channel 01: FXS Kewlstart (Default) (Echo Canceler: mg2)

I keep getting a red alarm when trying to setup asterisk to use my TE420B EC. I only have a blank context setup in my extensions.conf as I haven't started to config that until I can clear this red alarm. I don't have physical access to the server, so I can't go reseat the modules/card/ethernet cable, though I have hands on location that have done this a couple times

Hello, I'm facing problem where as whenever there are incoming call from pstn, there will be no audio coming in. User at the other end also could not hear my voice. This happens few days back. Im using asterisk 1.6.1.2 with dahdi tool 2.2.0. I thought it was time to upgrade, so upgraded to dahdi 2.2.1 and asterisk 1.6.2.5. However, it does not help at all. My current config as follows :-

Hi, Running 1.4.26.1 here. I have installed TE420B card in my server, and followed the appropriate steps (as far as I know to configure it). This TE420B is connected to a CLEC (T1s), so I am using pri_cpe as singalling type. When I dial out, I get this message: Dec 4 11:37:31] WARNING[27983]: app_dial.c:1275 dial_exec_full: Unable to create channel of type 'DAHDI' (cause 0

Hello group, I am installing Asterisk on a new pc running Ubuntu 12.04.3 Server. ?I have dahdi-complete-2.7.0.1+2.7.0.1, and have tried 2.6.1 and 2.8.0-rc1 and 2.8.0-rc2. ?I am following along in the ASTERISK The Definitive Guide 4th Edition and on page 116 when I issue the command $ sudo /etc/init.d/dahdi start I get the following error: Loading DAHDI hardware modules: ? ?wctdm24xxp: done

As best i could figure it out, I've installed dahdi and rc4. My TDM400P doesn't answer fxo or fxs. /etc/dahdi/system.conf: loadzone = us defaultzone=us fxoks=1,2 fxsks=4 /etc/asterisk/chan_dahdi.conf: [house-phones] context=internal ; Uses the [internal] context in extensions.conf signalling=fxo_ks ; fxo_ks Use FXO signalling for an FXS chanel dahdichan => 1 ;

Hi All, I have installed asteriskNow with Asterisk 1.6.2.11 and FreePBX 2.7.0.10. I have configured x100p fxo card in my asterisk box. But in my cli mode i am not getting the command *"dahdi show status"* Output of CLI : astrisks*CLI> *dahdi show status* No such command 'dahdi show status' (type 'core show help dahdi show' for other possible commands) I

[18884732963 at from-fax-machine:... - your call is hitting the from-fax-machine context - yet your 'fax' exten is in the from-pstn-4 context. See the "[2011-03-17 13:40:29.6] NOTICE[8825] chan_dahdi.c: Fax detected, but no fax extension" line. When Asterisk detects an incoming fax tone - it tries to automagically route the call to the 'fax' extension in the SAME

I am having trouble with chan_zap.so not loading. When I load it from modules.conf, Asterisk bails out without any error message. When I load it from the console, it just says "Unable to load module chan_zap.so" no matter what verbose level I am using. dmesg says: Zaptel Version: 1.4.4 Zaptel Echo Canceller: MG2 Freshmaker version: 73 Freshmaker passed register test Module 0:

Hi All; To overcome the echo problem, what mainly I have to do in the configuration other than the following line in the system.conf under dahdi directory? echocanceller=mg2,1-16 1) How can I know if the digium card supporting echo cancellator? 2) If I am getting a message in the consol that unable to enable the echo cancelator, then what does it means? The hardware is not supporting echo

after installing asterisk 1.4.23.1 and dahdi-linux-2.1.0.4 and at CLI> module load chan_dahdi.so receive the following: signalling must be specified before any channels are. CLI> Warning [4663]: chan_dahdi.c:11627 process_dahdi: Ignoring signalling Error[4663]: chan_dahdi.c:10946 build_channels: Unable to reconfigure channel '1' Error[4663]:

# Span 1 span=1,1,0,esf,b8zs bchan=1-23 dchan=24 echocanceller=mg2,1-23 # Span 2 span=2,2,0,esf,b8zs bchan=25-47 dchan=48 echocanceller=mg2,25-47 # Span 3 span=3,3,0,esf,b8zs bchan=49-71 dchan=72 echocanceller=mg2,49-71 # Span 4 span=4,4,0,esf,b8zs bchan=73-95 dchan=96 echocanceller=mg2,73-95 # Global loadzone = us defaultzone = us Span 1: TE2/0/1 "T2XXP (PCI) Card 0 Span 1"

Hello, My first attempt to get dahdi running on 1.4.28... with a Rhino 8 port modular card and a single FXS module. Got the Rhino card installed and the machine sees it: root at pbx:/etc/dahdi# dmesg | grep rcbfx [ 71.985309] rcbfx 0000:04:00.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21 [ 71.985440] rcbfx 1: Rhino PCI BAR0 50100000 IOMem mapped at ffffc90008d7c000 [ 71.985504]

Hi, I know it sounds weird, and this is part of the reason I have not reported that sooner. As I upgraded from 1.6.2.x to 1.8.x several months ago I am experiencing this problem. If a call is initiated from a DAHDI extension after no DAHDI extensions were used for some time, arbitrary DTMF digits are skipped and the call fails. If the call is redialed it goes through. Normally just one (1)

What is involved in provisioning Asterisk to use a multiline analog service from our local telco? I will only have one twisted pair entering in on a OpenVox card but am not sure how Asterisk interprets and deals with two incoming calls and/or two outgoing calls? Thanks! jlc

I am unable to dial out over a Wildcard TDM400P. This was working previously, so must have messed up the config somehow. I'm running Asterisk 1.6.0.15, with FreePBX 2.5.2.2. When I dial, I see: -- Executing [s at macro-dialout-trunk:19] Dial("DAHDI/1-1", "DAHDI/g0/9239220,300,") in new stack == Everyone is busy/congested at this time (1:0/1/0) It looks like the