similar to: ignorant question about Digium cards and MeetMe

Hello everyone. I have a timing slips errors and I can't understand what source of the problem is. My installation has 2 digium cards: TE420 and TE220 cards in one server. There are 3 spans (E1) to PSTN and 3 spans to internal PBS stations - normal installation for transit communication. Span configuration is: span=1,1,0,ccs,hdb3 #TE420 - first port. To PSTN. span=2,0,0,ccs,hdb3 #TE420 -

Hello folks. I've got a strange issue. When I modprobe TE220 I do not see mesages like Launching card: 0 <..> Setting up global serial parameters. You can see how I loaded and unloaded the card for several times - http://asteriskpbx.ru/pastebin/11 lspci can detect the card: 03:08.0 Communication controller: Digium, Inc. Device 0220 (rev 02) dahdi_hardware also: astpbx ~ # dahdi_hardware

Hi, Just trying to figure out / solve some echo issues with one of our systems. The server is a Dell R710 running Asterisk 1.6.x and Dahdi 2.2.x The card in the server is a TE121P (with VPMADT032 echo canceller) We are experiencing some weird echo issues with our Cisco 79xx phones, only when we are dialing out via the PRI. The echo is like a side tone, where we can hear ourselves speaking. The

Hello, I'm having problem connecting my Asterisk 1.4.29.1 with Digium TE420 to providers Cisco 2800 with VWIC-1MFT-E1 card. the same card runs fine with another E1 provider. TE420 led's lite green. Message type: RELEASE COMPLETE (90) < [08 02 80 ac] < Cause (len= 4) [ Ext: 1 Coding: CCITT (ITU) standard (0) Spare: 0 Location: User (0) < Ext: 1 Cause:

hi folks. i have a Digium TE220 PCI-E 2 port T1/E1 controller installed in an IBM x3400 server. i load the wct4xxp driver seems ok. but when i execute "ztcfg -vvv" command. the kernel panic. i tried zaptel 1.2.21 & 22. they have the same result. following is my zaptel.conf: loadzone=cn defaultzone=cn span=1,1,0,ccs,hdb3 span=2,0,0,esf,b8zs bchan=1-15 dchan=16 bchan=17-31

Hello! I am trying to configure my digium TE220 dual-span pci express card with Dahdi. I seemed to have managed to set up the card with the Dahdi kernel, as demonstrated by executing dahdi_scan: [1] active=yes alarms=RED description=T2XXP (PCI) Card 0 Span 1 name=TE2/0/1 manufacturer=Digium devicetype=Wildcard TE220 (4th Gen) location=Board ID Switch 0 basechan=1 totchans=31 irq=16

Hi All, I have a TE121P card installed and since connected it to the PRI I keep getting the Current Alarm as continually changing from Blue Alarm/Recovering and Recovering. The config I have is: /etc/dahdi/system.conf bchan=1-15,17-31 dchan=16 echocanceller=mg2,1-15,17-31 loadzone = cn defaultzone = cn /etc/asterisk/chan_dahdi.cfg [channels] Context=telco

Hello I am trying to configure TE420P but i am confused what to give chan_dahdi :( Below is configuration i am using for TDM400P Please help what changes to make in it... Please provide a link as well [trunkgroups] [channels] ;default for channels switchtype=national rxwink=300 hidecallerid=no callwaiting=yes usecallingpres=yes callwaitingcallerid=yes threewaycalling=yes transfer=yes

Hi, I have some servers that are dedicated to do meetme conferencing. From some previous test i concluded that I need to use dahdi_dummy as it is more accurate. If I did use the core timers in dahdi (not loading dahdi_dummy) I got bad quality in the conferences and dahdi_test showed 99.6% as worst. I thought maybe the issue as bad hardware for the timing or something else. But today I

Hi, Our potentiel next phone provider ask me a question i can't answer for sure, maybe someone here knows ? He says that is equipement only support VN4 protocol or more, or ETSI, however i can't find matching terms in the digium documentation or the chan_dahdi/dahdi/system.conf files... Any idea ? regards

Asterisk 1.4.32 dahdi-2.3.0.1 Centos 5.5 Digium TE420 CAC channel bank (2) Cisco RVS4000 router Cox 50 Mbps/ 5 Mbps cable modem Flowroute provider codac G-711 90 % CPU idle callwaiting=no When there are 10-15 or more calls up the farend hears a callwaiting like beep every 3 to 6 sec. the duration of this "beep" is very short and would be no problem if it didn?t happen every few

Hi: I want to have conference call with asterisknow and need 2 ports E1.Which Digium card is better?TE212 or TE220.I haven't problem with motherboard. Regards. --------------------------------- Get the Yahoo! toolbar and be alerted to new email wherever you're surfing. -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi All I'm having some serious kernel panic while using digium cards. It may be related to IRQ shared. Can this cause a lot of drop call and bad voice quality ? Do you guys know if there is a way I can assign one IRQ for each digium card ? Thanks a lot. Here is the output of /var/log/syslog kernel: [ 3821.982893] Uhhuh. NMI received for unknown reason 20. kernel: [

Hi all, When the Dahdi driver detects DTMF, it seems it's not muting the first 5-15 ms and sometimes the last 2-10 ms of the DTMF tone. This shows up in recorded voicemail greetings -- you hear a very short DTMF '#', or sometimes two blips, at the end of the recording. I have a Mitel SX-200 connected to Asterisk 1.6.0.1 by a couple of Digium cards: a TE420 w/Octasic and pri_net

Hi to all. I'm trying to use meetme on asterisk 1.4.22.1. On a debian i've compiled (as i need h323 support) openh323_v1_18_0 pwlib_v1_10_0 dahdi-linux-2.1.0.3 dahdi-tools-2.1.0.2 asterisk-1.4.22.1 All works fine, dahdi status is: asterik:/data/programmi# /etc/init.d/dahdi status ### Span 1: DAHDI_DUMMY/1 "DAHDI_DUMMY/1 (source: RTC) 1" (MASTER) asterik:/data/programmi#

I'm playing around with an ALIX 2D2 board (http://www.pcengines.ch/alix2d2.htm). It's a fanless, x86 system using an AMD Geode processor with 256MB of RAM. Also available are two network interfaces, two USB ports and one serial port (no keyboard or VGA). I'm using the Voyage Linux distro, which basically is Debian Lenny optimized for this board. Asterisk 1.6.1.12 runs fine on the

Hi I'm having problems getting the TE420 working in HP DL380G5 servers. The cards don't seem to be detected 100% by the BIOS. With two cards in the server they are never detected. things I've tried: 1 Update firmware to latest (P56) for the server 2 change irq settings 3 disable all onboard devices on server and remove raid controller 4 different cards in different slots What I

I am having a problem with a new PRI turn-up on dahdi 2.5.0 and asterisk 1.8.5 that I have not seen before. The PRI is setup as B8ZS, ESF and the span shows up and ok. This PRI is merely a crossover T1 going into an old DC0 class 5 switch. I am getting the following errors over and over again [Aug 16 10:26:10] NOTICE[8002]: chan_dahdi.c:3043 my_handle_dchan_exception: PRI got event: HDLC Bad FCS

Hello! At the end of year 2013 I had problem on my supermicro system with TE133, namely it losted connect to another system. So I opened case and finally card was replaced by TE220. Now I need to buy another 1 port card for almost the same supermicro. Could somebody tell me is this problem resolved? Thank you!

Hi, I am running Fedora 7 VM. On an earlier configuration with zaptel and Asterisk 1.4.21 , meetme worked alright. I upgraded to Dahdi and Asterisk 1.4.26, and the result is choppy sound via Meeme, while a simple Musiconhold works OK with descent audio quality. So I am sure its a Dahdi_dummy problem. Running dahdi_test gave me very poor results. Opened pseudo dahdi interface, measuring