similar to: Why do Zaptel calls drop all of a sudden? Could busy detect be the problem?

I have a couple of X100P's in my system and while on calls they just randomly hang up for no reason. I have tried messing with the busydetect and callprogress setting them to yes and no same and still random hangups. Is there another setting I should be looking at? My zap config looks like. context = inbound-work include => extensions signalling

So I made the mistake of buying a Carrier Access channel bank without noticing the page on the wiki about the fact that they don't support disconnect supervision (bastards!). However, apart from that, I do have it working fine for incoming calls. Is there some trick to get asterisk to detect the hangup tones from SBC? I've tried busydetect and callprogress as suggested, but neither

Hello, my config : aah 2.6 (asterisk 1.2.4) , centos 4.2, 1 TDM11B (1 Fxo / 1 fxs ), 1 phone, 1 softphone I'm in France When someone from PSTN calls and hangs up before the call is answered, internal extension keeps ringing until timeout occurs. PSTN line keeps busy. Hangup detection doesn't work. I've played with different paremeters (callprogress, busydetect, busycount,

I've been trying to get a Win 2000 RAS server working with my asterisk PBX for quite some time, to no avail. I've googled, I've tried loads of configurations, I've rewired phone lines, and still I am not winning the battle. Here's my config. PRI->T400P->Asterisk->T400P->Adtran 750(L36 Firmware)->RAS Server. I have 4 Zap channels signalled FXO_KS to the 750

I have a very strange problem I'm hoping someone has encountered already. I've scoured the internet for an answer to this one. My phone company provides no disconnect supervision. Hence I'm forced to use the busydetect feature. I have a TDM400 with two FXO ports. If I call from an internal extension to a landline and then hangup the landline Asterisk detects the busy signal

Hi, I had been using 4 X100P cards in my Asterisk box, but 2 of them were sharing an interrupt. Therefore, periodically I would hear beeps and clicks that I had assumed were a result of this. So, I ordered a TDM400P with 4 FXO modules and installed it in the box last night. Today, we've had nothing but problems with it dropping calls. I installed the latest CVS of everything, and we've

I have a customer running Asterisk 1.2.13 with Zaptel 1.2.11 that is having calls dropped. Sometimes you can stay on the phone for a long time and sometimes the call is dropped within a minute. There are 9 lines connected to 3 TDM04B cards. The Panasonic Pbx we replaced did not have this problem. There are 8 SIP phones and 16 analog phones connected to two Astribank-8 units and everyone

Guys, this is weird.. Today I started having some problems with calls been dropped. Im suing X100p cards (clones) and I have this setting on my zatala fle: [channels] language=sp signalling=fxs_ks usecallerid=yes cidsignalling=bell cidstart=ring hidecallerid=no callwaiting=yes usecallingpres=yes ;sendcalleridafter=1 callwaitingcallerid=yes threewaycalling=yes transfer=yes canpark=yes

Hi, I am trying to forward calls to another * server with IAX Here is What I want to Do 1- Call SERVER1, let say at 51412345678 2- SERVER1 should transfer the call to SERVER2 in a remote location 3- SERVER2 Receive the call and transfer it to the PSTN number. I have one X100P card on each machine. What is happening is that when the remote party picks up the phone, all he can hear is a weird

Hi, I'm having random hangup problems with zap channels. If I turn busydetect off in Zapata.conf, * fails completely to detect a user hangup in the middle of a script. On the other hand, if I turn it on, everything works much better, but long calls tend to be hung up without a motive. Any other parameter that I can try? Any #define that I can tweak and recompile? Will callprogress

Hi List, I've got * randomly hanging up on inbound or outbound calls on zap channels. I use a Digitnetworks X100P clone card. Any idea of what might be happening? Cheers, Jean-Michel.

Dear List members, After succesfully installing the * on a couple of systems, and putting them on test, I observed that there is an intermittent call drop on PSTN line. The systems are - Dell Optiplex P3/500MHz/128MB - Built-in ethernet - 1 X100P (Motorolla chip) card on PCI - 10G HDD etc. - Asterisk April 17 CVS. - 2 Mediatrix FXS ATA (4 phones) - 2 Grandstream phones. - sip.conf, zaptel.comnf

i am have x100P clone, and install asterisk 1.4 and out call normaly and hangup in xlite to zap but call to asterisk for zap channel nop pass to xlite and the caller hangup the asterisk not detect. what is the problem ??? -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20070720/39d4c1e8/attachment.htm

FYI to anyone else who may be experiencing random hangups; I removed the busydetect=yes lines from the conf files on my asterisk servers, and haven't had a hangup since. I had done that once before and it didn't seem to have much of an effect, so I'm not breaking out the champagne yet. But so far over dozens of calls both made and received since I took that line out, I

Hello, I have recently purchased a TDM400P card with one FXO expansion card, and I'm having problems. The card does not pick up incoming calls. Asterisk detects the ringing line and rings various SIP phones as required. When a sip phone answers, the sip user hears nothing and the PSTN user continues to hear ringing. Here is the asterisk output for an incoming call:

Hi I know this gets covered fairly regularly, but I've had a search through the archives and can't find anything dealing with this specifically - apologies if I've missed it though. I've got a TDM11B with the fxo port plugged into a standard UK BT PSTN line, loading wcfxs with OPERMODE=UK. All's working well, except if I get an incoming call through my bt line, and the

Is anyone having/had a problem with a TDM400P card hanging up on STD outbound calls as soon as the called party answers. I'm guessing that * is responding to the STD pips in some way. -- Howard. LANNet Computing Associates; Your Linux people <http://www.lannetlinux.com> ------------------------------------------ "When you just want a system that works, you choose Linux; when you

Dear All, I am trying to setup an ISDN line from local telco on a digium card. The problem I am facing is that I am not getting any caller id from the telco. They say that they have enabled caller id. Please help me out. My zapata.conf -------------------------------------------------------------------------------------------------------------------- [trunkgroups] [channels]

Hello. I am running asterisk 1.2.14 on a Dell poweredge with a Digium FXO/FXS card connected to 6 analog lines and using Linksys spa942 phones. My users are complaining of randomly disconnected calls, and when I watch the log (debug warning,notice,error), I don't see any cause. It looks like asterisk is seeing a hangup from the analog end. I have attached my zaptel.conf and zapata.conf.

Afternoon all, After doing some test on my asterisk box I can successfully receive calls to my Asterisk PBX to a SIP phone from The Telstra PSTN network Dial out from a sip phone is also not an issue, all calls connect and terminate normally. If I call the Asterisk PBX say from PSTN in Zap1-1 and out through ZAP2-2 back to the PSTN (after entering the correct pin off course) the card does not