similar to: Asterisk +Dahdi does not work with BRI NT

Hi all, As i tested with Asterisk+dahdi+libpri with openvox BRI with NT mode, the ISDN phone does not work. There is the setting and error. ***********************Enviroment********************************** Asterisk-1.6.1.18 dahdi-linux-2.3.0.1 dahdi-tool-2.30. libpri-1.4.11.2 CentOS-5.5 OpenVox B400P ******************************************************************** In my case , I set prot 1

Hi all, Last night I went to replace an Asterisk 1.4 + mISDN + b410p box with Asterisk 1.6.2 and DAHDI BRI - to no avail. I had two servers so copied network setting etc from the working one, moved the card across, ran dahdi_genconf etc and it didn't work. Here's the console output with notices disabled: lucas*CLI> pri intense debug span 1 Enabled debugging on span 1 [Dec 16

Hi All, I've a BT Versatility PBX that I want to connect to my asterisk 11.9.0 box via BRI port in NT mode but actually I wasn't able to get it working. I've another standalone PBX, it's a Panasonic model, which works fine connected to the same port. The BT connected to a UK BT BRI line works quite fine after roughly a minute once connected. The PBX can be seen at

Hi, I'm using revision 6822 of Dahdi Tools. # dahdi_hardware pci:0000:05:06.0 wcb4xxp+ d161:b410 Digium Wildcard B410P # asterisk -rx "dahdi show version" DAHDI Version: 2.2.0.2 Echo Canceller: OSLEC # cat /etc/dahdi/genconf_parameters ... pri_termtype SPAN/1 TE SPAN/2 TE SPAN/3 NT SPAN/4 NT #

hello: thanks for Tzafrir Cohen for dahdi testing. I installed dahdi-2.1-r3c svn code and asterisk1-6 for testing OpenVox B400P and junghans card. i fund that there is bug (i think) to dectect NT or TE mode. actually on the board, i set it as TE mode, but after start wcb4xxp, but it show the port is NT mode. to detect the TE mode, I modefy the code in base.c

Hi, I have 3 ISDN lines using the digium B410P card. Incoming and outgoing call are working. I use the following version : * libpri-1.4.10.2 * dahdi-2.2.1.1 * asterisk-1.6.2.6 On incoming calls, DTMF is not working, i can't see any logs. Here are the main configuration files : dahdi-channels.conf ;; Span 2: B4/0/1 "B4XXP (PCI) Card 0 Span 1" signalling=bri_cpe

Dear Supports, I was attempting to install BRI Card(OpenVox B800P) with wcb4xxp in NT mode .But I can not make it worked! Could you please give me some hints? Thanks in advance! Here are my environments: ------------------------------ CentOS-5.3 Kernel-2.6.18-164.el5 asterisk-1.6.1.6 dahdi-linux-complete-2.3.0+2.3.0 libpri-1.4.10.2 OpenVox-B800P(the first port is spliting into

Hi, I have a Junghanns QuadBri installed and seems to be detected and working correctly using the wcb4xxp driver All ports are configured as TE The problem is when I connect an ISDN line - the LED turns green and Dahdi status shows Alarm OK But when I try to make a call I get "All circuits are busy" cause 27 I have searched and web and tried numerous configs but it doesn't want to

Sir, i am using goautodial server , bri card is showing ok but when i try to call that showing below , This configuration is in doing in dubai , so kindly help me how can connet the call from this , what is my mistake is in this :::chan-dahdi.conf [channels] #include dahdi-channels.conf language=en context=default usecallerid=yes hidecallerid=yes callwaiting=yes usecallingpres=yes

Hello List, it is a very long time since I wrote here.... It has been still in Zaptel times.... Today I am run into a related problem: I can't get a DAHDI setup to work 100%. I am configuring an Astribank XR00013 (BRI, two ISDN ports). At some degree the installation (latest DAHDI drivers, Asterisk 1.6.0.18 on Centos 5.x) works. I can get incoming calls to the dialplan context that is

Hi, 1. Has someone met any success at all, connecting a Digium B410P to a Patton Smartnode 4638 (with latest 5.3 firmware) ? 2. If positive, then, which signalling was used on both sides ? My project's goal is use a Patton Smartnode 4638 to act as telco BRI lines, from a B410P-enabled asterisk box. In my testings, I can see channel is respectively up (with patton web server status page)

Hi, On my system I've got : CLI> dahdi show status Description Alarms IRQ bpviol CRC4 Fra Codi Options LBO B4XXP (PCI) Card 0 Span 1 OK 0 0 0 CCS AMI YEL 0 db (CSU)/0-133 feet (DSX-1) B4XXP (PCI) Card 0 Span 2 OK 0 0 0 CCS AMI YEL 0 db (CSU)/0-133 feet (DSX-1) B4XXP (PCI)

Hi All, I am facing problem with E1 line. I have installed Asterisk (1.4.20.1) on a system with Digium TE420 card (Zaptel- 1.4.10) But every now and then I face problem of down E1's. The log show lot of entries like "pri_dchannel: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 2" This happens on a regular basis and the E1 becomes up after some time. My

I have a 'CONGESTION' Status with R2 protocol. While testing this scenario sip GW--?Asterisk ?Digium E1 R2 Protocol?Cisco E1 R2 protocol?sip Gw Find below my error and configuration ,where are the errors in my configuration ? ========================================================================= Connected to Asterisk SVN-branch-1.6.2-r235775 currently running on

Hello everybody, I try to install -Ubuntu 8.04 server- a B410P and a TDM2400P together with Asterisk 1.4.26-2, dahdi-linux-2.2.0.2 and dahdi-tools-2.2.0. Problem I face is the following one: CLI> module load chan_dahdi.so == Registered application 'DAHDISendKeypadFacility' == Registered application 'ZapSendKeypadFacility' == Parsing

Hi there, we have a problem with dahdi and overlapdial. We are running an E1 in Germany and are in need of overlapdial. The E1 is connected to a Sangoma A101. As soon as overlapdial is set to "yes" we have problems with incoming audio on the dahdi channels. When set to "no" all audio is fine. Basically we can choose between being able to receive calls or to place calls

Hi all! I'm new with telephony cards and DAHDI drivers. I have installed Asterisk NOW 3.0.0 and update to Asterisk 11.7.0, modules are update too. I'm following the installation guide of Atcom [1] for AX1600P analogic card, modules are loaded [root at pbx ~]# lsmod | grep -E "hisax|netjet|dahdi" netjet 14618 0 isdnhdlc 4523 1 netjet mISDNipac

Hi everybody, In an Asterisk 1.6.0.5, dahdi-linux-2.1.0.4, dahdi-tools-2.1.0.2, with a Digium B410P and an OpenVox A400E, I can't make "dahdi_scan" to recognize the OpenVox. This card was working correctly but suddenly stopped working and I cannot make it work again. Both ?lspci? and ?dahdi_hardware? detect it but ?dahdi_scan? not and I cannot use it. >lsppci: *0a:00.0

Hi, 1. Is there any manual entry about modprobe's options relative to a given Dahdi driver (wctdm24xxp, for instance) ? 2. When loading a wctdm24xxp driver, is there any parameter to pass to modprobe to configure a span in NT/point to point mode ? 3. After running dahdi_cfg -vvvvv , I can read with dmesg : [ 1986.289277] wctdm24xxp 0000:04:06.0: xhfc: Configuring port 0 span 1 in TE mode

I've got an asterisk 1.4.24 box with dahdi complete 2.1.0.3+2.1.0.2 I've got a 2 port T2XXP card attached with on T1 currently plugged in. Inbound calls work fine, but outbound fail with the rather cryptic: [May 19 17:28:07] WARNING[11360]: app_dial.c:1237 dial_exec_full: Unable to create channel of type 'DAHDI' (cause 0 - Unknown) There are similar threads I've found on the