similar to: PRI - Native ZAP bridge fails - Is this my patch?

Hi Guys, Full PRI installed in Canada with Sangoma A101DE and Asterisk 1.4.21.2, LibPRI 1.4.10. Placing a call into PRI and then transfering that call out to another number. Problem is that the call rings out but the moment the other party pickups both legs of the call are disconnected give Cause code 16.

Hi all, I'm trying to insert a Rhino Ceros box equipped with a Rhino R2T1 dual-T1 card and running the latest version of Trixbox (2.4.2) between the central office and a Nortel Option 11. The switch at the CO is a DMS100. Basically, I'm taking the T1, connecting it to port 0 on the R2T1 card, and then connecting port 1 to the Nortel. (Actually a CSU and then the Nortel) We're running

I have a PRI E1 link between Asterisk 1.4.24 and Alcatel-Lucent OmniPCX Enterprise R9.0. As EuroISDN it works fine. However, I need to move to QSIG because of a firmware upgrade on the Alcatel PBX which doesn't support EuroISDN (please don't ask why). Besides, I've read somewhere that 2 B Channel Transfers "should" work with * 1.4, the latest 1.4 libpri and QSIG. So this

Hi all, I tried to connect the bristuffed(0.3.0-PRE-1i) * to an Alcatel PBX via BRI (zaphfc) and Q.SIG. The Alcatel PBX is connected to the outside world and should forward our calls to the telco. This setup works correctly as far as I use euroisdn as the switchtype. The first problem was that it is only possible to run the * side in CPE-mode -- I wanted NET. Anyway, I configured * this way:

I have a T1 link from asterisk 1.2.23 (also tried with 1.4.13) to a Meridian Option 61C. Calls either way drop with error "Channel 0/23, span 1 got hangup, cause 100". Can anyone offer insight into the cause and solution/workaround? (I tried upgrading to Ast 1.4.13, and upgrading matching zaptel & libpri, put the problem is identical). For testing, I tried a call from the

Hello all, the scenario: Carrier ----S2M------ * -----S2M------Siemens | | SIP Clients and many other features With much help from the list, the PRI links are without alarms and inbound calls are working fine (from both: Carrier and Siemens). But I am not able to dial wether outbound nor to the Siemens PBX. I allways get the message: == Everyone is busy

Hi, I have a problem with dialling internationals numbers, and I don't now what is the cause. I have one asterisk with a e100p card connected to the Telco (spain/telefonica) and it can dial local and national numbers without problems but when I try to dial a international number it hangs-up. I call the Telco to ask if the E1 can do international calls and it said that it can. I have tried

Hey all, I am running a Asterisk 1.2.9.1 with Sangoma A101 card, newest firmware, configured with a help from Sangoma Tech Support, running fine. It is connected to a PRI circuit split from Cisco MC 3810, which in turn is connected to a Converged T from CTC Communications. While Asterisk works fine and I can call in/out on my BV account, I am only able to dial in through CTC. I have spent

Hi! For demonstration purposes I try to bridge an incoming video call from a 3G mobile handset to another 3G mobile handset using asterisk as "switch". On the incoming call leg I see all expected bearer capabilities (Digital, 64k Transparent, G.7xx 384k video) but on the outgoing call leg the bearer capability G.7xx 384k video get lost and therefore the call is dropped from the mobile

PRI debug of the entire call would be great, also, switchtype would be awesome as well. Thanks! Matthew Fredrickson On Thu, Mar 24, 2016 at 4:07 PM, Carlos Rojas <crt.rojas at gmail.com> wrote: > Hi > > Did you activate the pri debug on the cli asterisk? > > On Thu, Mar 24, 2016 at 12:59 PM, Carlos Chavez <cursor at telecomabmex.com> > wrote: >> >>

Is there a setting somewhere in * to define whether I am receiving callerID or true ANI? Global Crossing claims they are sending ANI but I dont think so. My understanding of ANI is that it is always sent, regardless if callerID is blocked. If I dial *67 and my DID, I get "Presentation: Presentation prohibited of network provided number" and no number. Before I call GC on Monday

Hi, I have this setup: E1 PRI PSTN -- Asterisk -- Alcatel PBX - analog phones Can someone tell me what's wrong with this call initiating from an analog phone connected to Alcatel PBX? It dies with NOANSWER but all works if I call other destination numbers. Dialplan is a simple Dial(zap/g1/0984465691) statement. At the end you'll find also zapata.conf.

I have a server running Asterisk 1.4.14, Zaptel 1.4.6, Libpri-1.4.2 on a CentOS 5 server. The server has a single TE110 card connected to a provider called Alestra in Monterrey, Mexico. Since we installed everything we have been having problems dialing certain numbers, those numbers always fail when dialed from Asterisk but if you dial from your cell phone they always go through. I once has a

Hi, When have a incoming call from E1 to a extension FXS, and this extension is busy, the incoming call recive ring tone, and it is wrong. What can I do? Thanks in advance Pedro Here is the trace: asterisk-1*CLI> < Protocol Discriminator: Q.931 (8) len=41 < Call Ref: len= 2 (reference 66/0x42) (Originator) < Message type: SETUP (5) < Sending Complete (len= 4) < Bearer

Hi, When we make an outgoing call on ISDN (zaphfc) with overlap dialing we get immidiate hangup after answer. But when we place a full number before dialing everything is ok. Any help appriciated!! Thanks here is info with debug: == Primary D-Channel on span 1 up -- Executing Dial("SIP/200-164c", "zap/g1/|100|tc") in new stack -- Making new call for cr 192 --

We've got a EuroISDN (32 channels) with a TE405p, running cvs head as of 5 days ago. In the past couple of days, we've hit a scenario where incoming calls to the * pbx from the PSTN are being marked as busy, but outgoing calls work just fine. When we reboot *, the problem goes away. Has anyone else had this ? I've attached a PRI debug below. I've changed the phone numbers (x

Hello all, I have Asterisk 1.2.1 and a TE110P connected to a Nortel Meridian Option 81C system. The PRI line is currently setup as DMS100. Here are the relevant lines from zaptel.conf and zapata.conf: zaptel.conf: span=1,1,0,esf,b8zs bchan=1-23 dchan=24 loadzone = us defaultzone = us zapata.conf: [channels] language=en context=from-internal musiconhold=default switchtype=dms100

Hi. recently I have been trying to setup a PRI on asterisk. Inbound calls are working just fine but I am not able to make outbound calls. Does anyone know what I need to change to make outbound calls work? Right now the PRI is instantly hanging up on the outbound calls. I have included full debug info as well as config files. /etc/zaptel.conf span=1,1,1,esf,b8zs bchan=1-23 dchan=24

hello everyone, I have a trixbox server with an E1 card(not digium).It connects to an AVAYA pbx use E1. It works fine.But when i change the E1 card to digium TE220B,there is a problem. When sip extension A(on trixbox) call PSTN extension B(on avaya),A must wait longtime before B start to ring.From the log I find there are two times call. I don't know why the first request be rejected

OK I am going to do it again. Global Crossing is now sending ANI but it is not in the format I expected. Any one know of a way to get this data into two seperate variables? The first number is ANI and the second is DNIS so it is "*tendigits*tendigits* on one line like below. < Called Number (len=26) [ Ext: 1 TON: National Number (2) NPI: ISDN/Telephony Numbering Plan