similar to: Wanted: free DID number and provider feedback

What is wrong with IAX2 protocol? If IAX2 is so much better than SIP so why providers discontinuing support for IAX2 I was with provider "callwithus" but they discontinue IAX2 I switched to "checkbox.cc" but they discontinued it as well. What is wrong with IAX2? -- Joseph

Hi All, Anyone one info of where I can get a 'free' DID number ? I have setup my asterisk box (home) and want to learn more but I need a #. thanks in advance,

Hello, We had been seeing SIP-guessing attacks on our Asterisk server here. While it wasn't that hard to write a once-a-minute cron job to spank the lusers, that runs once a minute and creates little spikes in the usage and I/O graphs, and is slower to respond than I'd really prefer. I felt that it'd be much cooler to get something more comprehensive put together. We don't use

A lot of people are going for the "VOIP only" approach, but SBC says you have to have an active analog voice circuit before they will sell you DSL. Does anybody know which DSL providers will sell you DSL without making you pay for a voice circuit? Thanks in advance, ------------------------------------------------------------------------ Steve Edwards sedwards@sedwards.com

Greetings - We've a pair of ISDN BRI that we use for dialtone, fairly happily except for the recent meltdown of one of our Netgear RT338's. We're in the middle of slowly migrating to a VoIP/Asterisk-on-FreeBSD based phone system. I had originally considered just buying a Digium TDM400 card and continuing to use the RT338's to bring out POTS lines from the BRI's, but the

Soemthing goes wrong with this mail list: I am getitng something like it: >Sorry. Your message could not be delivered to: >Aster risk (Mailbox or Conference is full.) ?????????? Regards, Corvin

Whats up to VoipJet.com? Their DNS servers are not reachable. Both primary and secondary are on the same subnet - weird setup. Thanks, David

Cisco 7960 Upgrading from 6.x to 7.3 get Protocol Invalid. I'm sure this has been discussed but has anyone figured this out. Regards, Juan Staalenburg Teksavers, Inc. (512) 255-8395 x1002 AIM: juanteksavers

Hello everybody I have a FreeBSD 6.1 box and i would like if exists know issues in asterisk to run in this unix operative sytem I want to know it :) Best regards and thanks in advance Mario

Hello all, Just got hold of a CISCO 7960G. Updated the Firmware to the latest 8.2. As you all know it has 6 lines which is why i bought it. Just would like to know from you experts if this piece will connect to 6 different providers over the internet or will it only work as 6 extns with 1 provider. Im not able to get connected to more than one provider. Also i have found that the time is not

delivery of the signal, and route the signal around internally digitally, if you have ISDN. This means, for example, that our USR Courier I-Modem, which can terminate a 56K call *digitally*, results in my being able to make a 56K connection from most modern cities here in the US, without wasting an ILEC ISDN BRI line dedicated to that purpose, by having the PBX connect an extension to the

We are in the process of preparing to move our Asterisk server to a Digital T1 interface card instead of a analog card (via an Adtran which is now connected to the T1). I did a preliminary test the other day and hooked the T1 line up to the T1 card, bypassing the Adtran. This worked rather well I must say. The two issues I ran into are: 1) Caller ID is not working even though I enabled

Hi all, I'm diagnosing a problem related to PRI card. I would like to know the following: assuming I've got a working PRI card and correctly installed Linux drivers and a PRI line connected to the card, even without starting asterisk, shouldn't I hear a ring tone when I dial the number? I'm getting busy tone all the time. I'm thinking the patch cable I made may be causing

OK, I asked this about a week back and met with no repsonse at all. But perhaps its worth trying again. Does anyone on-list have * running BRI to their local telco? I'm considering this as an alternative to my TDM400p card. Michael -- Michael Graves mgraves@pixelpower.com Sr. Product Specialist www.pixelpower.com Pixel Power Inc.

Hello For those SOHO customers (ie. at most, a couple of POTS/ISDN connections and simultaneous SIP calls) who'd rather not use a big, noisy PC to run Asterisk, I'd like to offer an alternative that has the following features: - not old hardware sold on eBay, ie. it must be up-to-date hardware sold by a company currently in business - compact, silent - has room for a 2.5" hard-disk,

Hello! There is something I really don't get: As I ordered a PRI ISDN line in Germany with DID, I had not to pay anything for a "DID number block", now I'm trying to get a PRI ISDN in the U.S. (CA) and SBC wants to charge more than 200 USD/month for numbers. I mean, this has nothing to do with DID, where everything that comes after the "base number" will be

I am totally new to this project, I have been trying to set it up now for almost a whole day, and can not understand what is wrong. The following error appears when my phone tries to register: Oct 6 19:08:30 NOTICE[98310]: chan_sip.c:7519 handle_request: Registration from '<sip:2201@192.168.0.5;user=phone>' failed for '192.168.0.253' What exactly does this error mean,

> > On a related note, I wanted our phones to display "city, st" for the > > caller-ID name in the event that none was provided. > > Interesting code. What sort of memory does * take up when you load up > all those CLID values? > > Nathan > I am a little late to this thread, but the answer is WAY TO MUCH. With 150,000 "pattern" match

Hey everybody, I wanted to know what other may be doing to stem the flood of inbound junk faxes? We currently using Asterisk/iaxmodem/Hylafax for fax services and get a number of junk faxes daily. Most (If not all) of them have caller-id blocked and have a TSI of "". I was hoping that, since we are using a PRI, there would be other information coming across that I could use to

Having had various issues with local vendor (begins with "V"). am looking to move to all wireless. Anyone know if current vendor can refuse to port the current land line numbers to a wireless provider? >From what I've read, the Fed's seem to say "no", they cannot refuse, or impede this. joe a.