similar to: No Audio on pstn call

Hi All, I have installed asteriskNow with Asterisk 1.6.2.11 and FreePBX 2.7.0.10. I have configured x100p fxo card in my asterisk box. But in my cli mode i am not getting the command *"dahdi show status"* Output of CLI : astrisks*CLI> *dahdi show status* No such command 'dahdi show status' (type 'core show help dahdi show' for other possible commands) I

Hi, I've seen this USB product from Sangoma : http://www.sangoma.com/products_and_solutions/hardware/analog_telephony/usb_fxo.html Is it working ok ? Is it easy to integrate it with Asterisk ? How would you rate your experience with it ? Regards -------------- next part -------------- An HTML attachment was scrubbed... URL:

I am trying to find an example of how to set up my FXS Station Card in my Asterisk. I have (1) XP100P I have (1) tdm20B (2 Port FXS) Could someone tell me if this is correct? /etc/zaptel.conf fxsks=1 fxoks=2 fxoks=3 loadzone=us defaultzone=us /etc/asterisk/zapata.conf [channels] ; language=en ; ;X100P Port 1 context=inbound-analog signalling=fxs_ks usecallerid=yes echocancel=yes

Hi. I have a x100p card installed on my asterisk box... my zapata.conf file includes the following lines: [channels] context=default switchtype=national signalling=fxo_ls rxwink=300 echocancel=yes rxgain=0.0 txgain=0.0 group=1 callgroup=1 pickupgroup=1 Basically, the zapata.conf file generated by make samples. Then in my extensions.conf I have this: [default] include => demo And demo is

I am having problems with * not hanging up an incoming PSTN line, if that line is not answered before the person calling in hangs up. The line hangs in various states, it has hung with a busy tone, with no tone at all. I am running *@home and have a digium 4port line card. This was configured by the genzaptel command I then added trunks for each line. I also have a Pulver WiSip phone which I

Charles S. Antrim wrote: > I am using a card that has an fxo and fxs module. I am no where near an expert but I have my sip phone working through my pstn line and this is my config. /etc/asterisk/sip.conf [general] port = 5060 bindaddr = 192.168.69.1 context = sip disallow = gsm allow = alaw disallow = ulaw nat=disable srvlookup=no localnet=192.168.69.0/255.255.255.0 subscribecontext =

Hi, Im getting mad with this error, I have a x100p installed with wcfxo module loaded perfectly, I can receive incoming calls and detect very good the hangup for incoming calls. But for outgoing calls its a mess. When I place a call for outgoing, i heard the ringing, my cell or phone rings and when I pick up the phone it hangs: -- Called g1/91xxxxxxx -- Hungup

Some recent issues I had with hardware seem to come back to not understanding two very similarly named files: /etc/asterisk/dahdi-channels.conf /etc/asterisk/chan_dahdi.conf I've modified the chan_dahdi.conf to work now, but it would appear all I needed to do was include dahdi-channels.conf in chan_dahdi.conf and the problem would not have persisted? Is it me or is that a bit Monty Python?

All, I'm having trouble getting the X100P working. Lsmod shows : zaptel 179808 0 I did a . # modprobe zaptel and here is my zaptel.conf (comments omitted) __SNIP__ fxsks=1 loadzone = us defaultzone=us __SNIP__ Here is zapata.conf __SNIP__ [trunkgroups] [channels] context=default switchtype=national signalling=fxo_ls rxwink=300 usecallerid=yes hidecallerid=no

Hello All, I am getting a set of errors when I boot Asterisk that I have not been able to solve. What is causing these error(s)? Asterisk boot output: ============== Asterisk CVS-04/10/04-21:44:51, Copyright (C) 1999-2001 Linux Support Services, Inc. Written by Mark Spencer <markster@linux-support.net> ========================================================================= [

I got two phones on an ATA-186 (601, 602) and two phones on the TDM22B (603, 604). I have two lines on the TDM22B. I cannot figure out some of the problems: 1. 601 dials via ZAP/3-1 to local phone number at PSTN: ringing pickup on PSTN (empty) still ringing in the phone set 601 2. call from PSTN back: 601 picks up ... everything works !!! No caller id shows up 3. For testing I have only one

Yo! I changed callprogress to no, and in wcfxo.c source around line 334 i changed the value 32000 and -32000 to 10000 and -10000 because it had something to do with the DC voltage when it was ringing. I found reference here (http://www.voipuser.org/forum_topic_1791.html) with an interesting diagram of wiring that was incorrect for sending voltage to a phone or something like that. So put it

Don't know enough to properly term the problem I'm seeing... sorry if subject appears vague. And I have other questions too, but "Newbie Help Wanted" isn't exactly more specific... ;-) My setup, intended for testing and all, "*" version 1.6.0.6, dahdi with an X100p clone. Regular phone line provides PSTN access with one port (and my DSL). Calls come in and are

Hi, Running 1.4.26.1 here. I have installed TE420B card in my server, and followed the appropriate steps (as far as I know to configure it). This TE420B is connected to a CLEC (T1s), so I am using pri_cpe as singalling type. When I dial out, I get this message: Dec 4 11:37:31] WARNING[27983]: app_dial.c:1275 dial_exec_full: Unable to create channel of type 'DAHDI' (cause 0

# Span 1 span=1,1,0,esf,b8zs bchan=1-23 dchan=24 echocanceller=mg2,1-23 # Span 2 span=2,2,0,esf,b8zs bchan=25-47 dchan=48 echocanceller=mg2,25-47 # Span 3 span=3,3,0,esf,b8zs bchan=49-71 dchan=72 echocanceller=mg2,49-71 # Span 4 span=4,4,0,esf,b8zs bchan=73-95 dchan=96 echocanceller=mg2,73-95 # Global loadzone = us defaultzone = us Span 1: TE2/0/1 "T2XXP (PCI) Card 0 Span 1"

I keep getting a red alarm when trying to setup asterisk to use my TE420B EC. I only have a blank context setup in my extensions.conf as I haven't started to config that until I can clear this red alarm. I don't have physical access to the server, so I can't go reseat the modules/card/ethernet cable, though I have hands on location that have done this a couple times

Dear All; I am afraid from IRQ misses: 1 The ISDN E1 was working fine on the machine, the electrical disconnected and then the Red Allarm. I checked the dahdi and I found that I have to reinstall dahdi again and I did. But still not becoming UP. The output of the cat /proc/dahdi/1 is following (I am afraid from the IRQ misses: 1, so if it is a problem what is the solution)? [root at CC

Hi, I've searched and searched on the possible problems. If anyone can help me that would be great. Span 1: TE2/0/1 "T2XXP (PCI) Card 0 Span 1" (MASTER) B8ZS/ESF CRC4 error count: 4750 E-bit error count: 5023 Timing slips: 72 1 TE2/0/1/1 Clear (In use) (SWEC: MG2) 2 TE2/0/1/2 Clear (In use) (SWEC: MG2) 3 TE2/0/1/3 Clear (In

Hello I'd like to configure Asterisk so that... 1. I ring it from my cellphone with CID number displayed, just to notify Asterisk that I wish to make a call 2. Asterisk waits until I hang up, calls me back, and prompts me for the number I wish to call 3. Asterisk puts me on hold through Flash(), which is apparently the equivalent of hitting the R key on European handsets 4. Asterisk calls the

Hello I've tried a bunch of things, but still get errors/warnings when using the IF() function: ============== TEST #1 exten => h,n,Set(WAV_FILE=${IF($[ ${STAT(e,/tmp/${CALLTIME}.wav)} ]?${CALLTIME}.wav)}) [Nov 26 21:52:34] WARNING[5074]: func_logic.c:107 acf_if: Syntax IF(<expr>?[<true>][:<false>]) ============== TEST #2 exten =>