similar to: Intel Atom based Asterisk server?

I have tried installing many of the beta versions and most of the release versions of 1.8. I have 3 SIP phones which we use for all our calls. After installing 1.8 the first thing I try is calling out port one of my Digium TDM04 back into port 2. I can see that the call comes in and tries to call all three SIP phones but the phones never ring. Eventually the call goes to voice mail and these

Hello everyone! I'm planning on setting up a new system shortly and can't pick the right card... We will have 2 or 3 lines coming in and 7 extensions (GXP2k's). Should I just get 2 or 3 X100P cards? Or do I need the Sangoma A20200 or even the A20200D (Echo cancelation)... I was thinking I'd use a Dell 2.0 GHz machine as the server... If anyone has suggestions as to

What are peoples experience with the reliability of the TDM400p. Specifically in the 2 FXO, 2 FXS configuration, which is the 022 (?) model. Is this board prone to random failures? joe a.

Hello, After solving the other "low hanging fruit" audio issues in our Asterisk PBX, we are left with occasional cases of severe echo which we have not found a solution for yet. Our system: - Asterisk 1.2.0-beta1 - TE110P on a PRI - TDM04 and TDM40, but these are unrelated to current echo issues - Fedora core 3 - Echo canceller KB1 Most calls have minimal, acceptable echo levels. But

Hi all I don't know what went wrong but i no longer seem to be able to compile asterisk. I first do : cd /usr/src/dahdi-linux-2.1.0.4 make clean ; make all ; make install cd /usr/src/dahdi-tools-2.1.0.2 ./configure ; make clean ; make all ; make install ; make config So far.... so good but then when i do : cd /usr/src/asterisk-1.6.0.6 make clean ; ./configure ; make all ; make install i

Hi, I'd like to know from other people's experience using Asterisk and Digium cards like the TDM410P and B410P on Atom system (.e. giwth D525 CPU) and Jetway motherboards. Any operational instability, unexpected freezes, etc or in your experience it's a stable combination? Thanks in advance for any sharing! Rgds. -------------- next part -------------- An HTML attachment was

Has anyone on this list succesfully managed to get two (or more) TDM04 (with four FXO each) working on a Dell PowerEdge server? If so, which model? Was it a hassle? I'm doing a seven-line installation and a callbank seems like overkill, I just don't want to get suck with a PowerEdge that gets into an IRQ mess. Thanks in Advance, Tom Hayden

Hello Asterisk, Back in 2009 I built a small Intel Atom based computer running Centos 5 for my asterisk system. 5 phones, 2 people 1 POTs line and six or so SIP numbers. So basically no load. I'm feeling like it's time to build another machine. It's probably silly, but it's been six years and I can't upgrade the OS which is falling behind. I'd likely just put

Hi, Digium stopped to produce TDM400P and the new TDM410 is too new to find it in our shops. The only alternative available is a "fully-compatible" Openvox product...but is it really "fully-compatible"? Any experience about Openvox products (card and zaptel versions, etc...)? Thank you! Giorgio.

I have an ATA-186 in a SIP configuration (following Shawn Djernes how-to), but I get the following error at the asterisk console when I try to call the phone connected to the ATA: ioctl(ZT_LOADZONE) failed: Inappropriate ioctl for device Failed to register zone 'United States / North America': No data available Everything works if I remove indications.conf from /etc/asterisk -

Hi! I installed shorewall shorewall-2.1.7-1 on a newly installed box. When using 1.4 versions I could enable shorewall in ntsysv, now shorewall doesn''t show up in ntsysv? I am running shorewall on a RedHat Enterprise Linux rebuild (www.taolinux.org). Is this a bug or a feature?

Hi list! Is anyone using the Kirk IP600/3 with SIP firmware connected to Asterisk? Any experiences / caveats? If anyone would be willing to share the dump of their IP600 config file, i would really appreciate it. Is there anything special i should put in my asterisk config? Thanks !!! Remco

Hi list! I've been bitten by a bug in the latest kernel 2.6.9-34.EL and I already removed the old kernel. Are old kernels retained at any place? I need to go back to 2.6.9-22.02 but where can I find it? In the Centos 4.3 directory I find only the latest kernel, not the older ones? Thanks!!

The information (or lack of it) on upgrading from zaptel to that @&*^QW%&^%!!! dahdi is very frustrating. I cannot find anything on how to uninstall zaptel, i found an earlier post to this list which suggested make uninstall and make remove in the zaptel directory which just generates errors and does nothing (on zaptel 12.1). Then i install dahdi-linux and dahdi-tools and i want to

I show the file size as 19M on the FTP site. 95MB is the gunzipped size. I suspect something unzipped it as it downloaded, I've seen browsers do that. I also pulled the file personally, and found the sizes lined up: ira at ira-t430:~/Downloads [/dev/pts/1](64/0)$ ls -la samba-4.1.19.tar.gz -rw-rw-r--. 1 ira ira 19558250 Jun 23 20:16 samba-4.1.19.tar.gz ira at ira-t430:~/Downloads

I have an analog GSM Gateway that is connected to a normal SIP ATA device. Basically what it does is this : when you call the extension nr. of the SIP ATA port, the GSM Gateway will pick up the phone and presents a (new) dial tone, and then dials whichever DTMF tones it received. The SIP ATA ia a Grandstream HT286. I would like to use the GSM Gateway to route my outbound cellular calls, how

I finally decided it's been long enough using my ancient HP junker and I built a Atom 330 based machine to replace it. I've installed Centos 5, Dahdi and Asterisk 1.6.2. After a bit of struggles getting the 1.2 version files converted to 1.6 almost everything seems to be working. All my SIP lines seem to work and calls come in as expected and all my DAHDI lines work with incoming

Hi! I have this rule to allow incoming VNC connections to a host on my private LAN: DNAT net:$SITE1 loc:$JOHN tcp 5900:5910 This works perfectly the host can connect without problems. Would it be possible to link the internal host to an external ip? For example if Site1 would connect on the VNC port, all traffic gets forwarded to loc:$JOHN. But if net:$SITE2 connects

I am having a problem with a couple servers. They both have a Digium TE110P and a TDM04B card. I have setup the system so the TE110P uses channels 1-31 and the TDM04B 32-35. The problem is that when we reboot the server sometimes the TDM04B is recognized first and the TE110P second so the configuration fails. I do not know why this happens and to solve this I have to do a "service

Hi! I'm trying to setup a Wildcard TE110P with a PRI in The Netherlands. I get a Red Alarm on the line. Is there any way of debugging this? I've tried some configs that should work but without success. Is there any way of telling if the cabling is correct or what else the problem could be? Thanks!! Remco