similar to: beroNet BN4S0e PCI Express ISDN Card with chan_dahdi

Hi, i use an BN4S0 with misdn an asterisk on Linux 2.6.9. The hfcmulti module is loaded with option: type=0x04 protocol=0x2,0x2,0x22,0x2 layermask=0xf,0xf,0xf,0xf and the fourth port is connected to an ISDN PTMP (MSN) port. Call to #72 from S0 (BN port 4) are not accepted from asterisk but why ? Can anyone give me a hint ?? misdn debug messages follows: lib: NEW_CR Ind with l3id:80001

I'm having trouble installing Beronet BN4S0 card. I have downloaded instructions from here http://www.beronet.com/download/card_installation_guide.pdf And when I download install-misdn-mqueue[1].tar.gz I untar it and execute "make" and "make install". This is the output that I get. [root@nbirma1 install-misdn-mqueue]# make install make -C app_bundle make[1]: Entering

Hello. Just installed the Beronet BN4S0 card. But i can't connect to my ISDN Line. misdnportinfo gives (what does ":Layer 4 protocol 0x04000001 is detected, but not allowed for TE lib" mean?): best regards and thanks t. asterix asterisk # misdnportinfo Port 1: TE-mode BRI S/T interface line (for phone lines) -> Protocol: DSS1 (Euro ISDN) -> Layer 4 protocol 0x04000001

Hi, I guess I'd need to run Beronet quad and octo bri cards under bristuff to get zaptel features (echo canceling, timing source).... Am I right or could I achieve this also with chan_misdn - their native driver ? Running bristuff on Beronet cards is unsupported. Has anyone succesfully run Beronet quad BRI cards under bristuff recently ? Do they work ? Regards, Rob.

Hi, I setup an asterisk system (asterisk 1.8-rc3, dahdi-linux-2.4.0 with dahdi-extra from Tzafrirs git, kernel 2.6.35.4). The hardware is an older pc system with Celeron CPU (2.5 GHz) with a Beronet BN4S0 ISDN card. The system starts without any errors. I discovered a severe issue. The kernel panics on a very small load. The first call normally gets through. If I start the second or third call

We have here a TandBerg "videoconferencing system" connected in asterisk with a Beronet card BN4S0 (4 BRI ports). I`m trying to make a videoconferece (video + audio) with this Tandberg to another Tandberg using the ISDN channels through the BN4S0 BRI Card. But, i'm only obtaining audio calls, the video not appears. When i try to make a 64K calls (data calls), the call does not

The Asterisk Development Team is pleased to announce the release of DAHDI-Linux and DAHDI-Tools version 2.5.0 DAHDI-Linux 2.5.0, DAHDI-Tools 2.5.0 and DAHDI-Linux-Complete 2.5.0+2.5.0 are available for immediate download at: http://downloads.asterisk.org/pub/telephony/dahdi-linux http://downloads.asterisk.org/pub/telephony/dahdi-tools

The Asterisk Development Team is pleased to announce the release of DAHDI-Linux and DAHDI-Tools version 2.5.0 DAHDI-Linux 2.5.0, DAHDI-Tools 2.5.0 and DAHDI-Linux-Complete 2.5.0+2.5.0 are available for immediate download at: http://downloads.asterisk.org/pub/telephony/dahdi-linux http://downloads.asterisk.org/pub/telephony/dahdi-tools

Good Evening, The company I work for is attempting to connect an Cisco ISDN Router to an OpenVOX B200P BRI Card so that we can get it to dial out across an existing ISDN PRI Line also installed in the Asterisk PBX Everything has compiled successfully and the BRI card has been detected when mISDN is started: # misdnportinfo Port 1: NT-mode BRI S/T interface port (for phones) -> Interface

Hi! In R 1.6.1. for Windows using RGui interface I try to use characters of Slovenian alphabet. Slovenia is a small Slavic country south of Austria with 3 characters which are not found in English alphabet, namely C, S and Z- all with caron. As S and Z are presented OK in both Console and Graphics window, this is not the case with C caron, which is shown as E acute- for an example please see:

Hi, I have a couple of questions about Quad-BRI solutions for Asterisk, and was hoping that I might get some feedback based on other people's experience. We currently use the Junghanns card, which is a pure Zaptel solution, which is fantastic, but they have no hardware EC solution, and their drivers are becoming increasingly un-stable with time (I back-port to a modified qozap driver from

Hi, we've purchased new Beronet Octobri card and have problems loading modules for stock Asterisk for Debian Sarge (it has bristuff patches in it). when loading qozap it says that no multibri card was found although lspci shows it... There were quite some rumours about bristuff not liking other than junghanns cards, but don't know if something happened.... Anyone recently used this

Hi, I've just installed a beronet BNS40 on Asterisk 1.2.9.1. Everything seems ok, asterisk gives no error (nothing inside logs) but the 4 led on the back of the card (which is NOT connected to an ISDN line) are red and flashing....what does it mean? Is it not properly working or it means the card is not connected to any ISDN line? The card handbook says the card has red led but not their

Hi list! Do anybody has success histories about using the Beronet app_saynumber application? For those that are hearing about for the first time, it?s a piece of software that enables the use of another language in say_number commands in asterisk dialplan or AGI scripts. Link to download: http://www.beronet.com/download/app_saynumber-beta-rc1.tar.gz I?m trying to compile it in

Hi, I'm currently using a beronet quadBRI and a Digium tdm400P card on a Poweredge SC420 DELL with mandriva 2005 LE (standard installation) but this particular configuration gives me a problem: sometime the 2 cards work well toghether, sometimes it is impossible to make/receive calls. Is there anybody out there who is currently using this configuration without problems? TIA Giorgio

Ciao, I have an Asterisk 1.2.9.1 box with a beronet dualBRI (install-misdn-queue) on a Debian distro. I'm experiencing problem with some Telecom Italia lines: some people cannot choose menu selections or extensions after hearing intro message. Is there anybody who knows if there is a particular parameter to set inside misdn.conf (or maybe some other configuration files) ? TIA Giorgio

Hi all, I have a problem with my beronet card with 2 isdn. I think drivers and Asterisk are ok but the red led on the card always blinking. The card is connected with PBX. I post some conf: [root@gateway ~]# misdnportinfo Port 1: TE-mode BRI S/T interface line (for phone lines) -> Protocol: DSS1 (Euro ISDN) -> Layer 4 protocol 0x04000001 is detected, but not allowed for TE lib. ->

Hi. I'm trying to get a Beronet QuadBRI card work with bristuff drivers. Though qozap module loads right, all card spans are in deactivated status. I'm quite sure my configuration is correct and using a single BRI card instead of the quadBRI the status is active and I can place and receive calls. On Beronet installation manual I read that Beronet and Junghanns cards are identical in

Hi, I did replace an old asterisk box by a new shiny one (2 BRI ports used on a quad port card - BeroNet PCI Express) I noticed a message in the logs that puzzles me: May 11 19:10:02 kernel: dahdi: Master changed to B4/0/1 May 11 19:10:08 kernel: wcb4xxp 0000:05:04.0: PCI INT A disabled May 11 19:10:08 kernel: wcb4xxp 0000:05:04.0: Driver unloaded. May 11 19:10:08 kernel: dahdi: Telephony

Hello. I have problems to integrate an isdn phone. I don't know why but the isdn phone rings only once and than it looses its connection to his base station. I can make a call from the isdn phone to an VoIP Phone inside my network but when i pick up the phone the isdn phone also crashes. misdn.conf: [ntport1] ports=5 context=isdn-telefon msns=* extensions.conf: exten =>